HARD PARTS

• Direct OEM replacement at a fraction of the cost
• Includes valve, hose, gaskets, screws, clamps and everything needed to replace the OEM petcock
• Viton rubber fuel resistant gaskets
• Includes OE style fuel line and clamps

Vertex valves follow high-end OE specifications, using steel or titanium with a pressurised hardness treatment.

• Follows high-end OE specifications.
• High-quality steel or titanium valves.

Rough riding calls for stronger axles and that’s where All Balls Racing excels. Machined for exact OEM fit, the shaft is made of chromoly steel with a larger diameter than most axles. The axle has 6 ball bearings in each CV joint. Laminate coating resists corrosion and rust, and protects axle from dirt, water, rocks and grease. Waterproof neoprene boots act as a first line of defense, shielding vulnerable joints and preventing leaks. High performance molybdenum grease reduces heat and friction.

• In static torsion trials, these axles were up to 30% stronger than OEM and aftermarket competition.
• Lasts approximately 50 percent longer than many aftermarket competitors.
• Typically runs almost 130,000 cycles versus 80,000 cycles for many axles.

Features:

• 40% stronger than OEM.
• Larger 4340 chrome-moly steel axle bar.
• Precision ground components.
• Low profile clamps.
• Neoprene boots.
• Engineered in the USA.
• Manufactured in an ISO facility.
• Assembled with 3% molybdenum grease.

Includes components necessary to complete a piston (top end) rebuild. Competitive pricing, made to meet and exceed OEM quality and designed as a direct OEM replacement.

Features:

• Designed for OEM replacement.
• Made from high-quality materials.
• Meet or exceed OEM specifications.
• Competitive pricing.

NOTE: This complete Vertex Gasket Set contains all parts as pictured.

Produced in the U.S.A. with the latest materials and technology in gasket production to Vertex specifications. Vertex gaskets ensure long-lasting performance and leak prevention for your rebuild needs. Vertex's replacement gaskets and seals are available as top-end kits, complete engine kits, or as an oil seal kit.

• One kit containing all of the gaskets, O-rings, and valve seals necessary to rebuild the entire engine and transmission.
• Includes transmission seals.

High-quality park hand brake cable from All Balls.

Features:

• Black PVC outer jacket for maximum flexibility and durability.
• Steel inner casing that is tightly coiled for low compression.
• A pre-lubricated nylon inner sleeve guarantees smooth operation and long life.
• All wire ends are bird caged prior to terminal casting for superior pull-out resistance.
• EPDM molded rubber components for high UV resistance and long life.
• Injected molded components are manufactured from high strength POM material.

Includes components necessary to complete a piston (top end) rebuild. Competitive pricing, made to meet and exceed OEM quality and designed as a direct OEM replacement.

Features:

• Designed for OEM replacement.
• Made from high-quality materials.
• Meet or exceed OEM specifications.
• Competitive pricing.

NOTE: This complete Vertex Gasket Set contains all parts as pictured.

Produced in the U.S.A. with the latest materials and technology in gasket production to Vertex specifications. Vertex gaskets ensure long-lasting performance and leak prevention for your rebuild needs. Vertex's replacement gaskets and seals are available as top-end kits, complete engine kits, or as an oil seal kit.

• One kit containing all of the gaskets, O-rings, and valve seals necessary to rebuild the entire engine and transmission.
• Includes transmission seals.

NOTE: This Vertex Top End Gasket Set contains all components pictured.

Produced in the U.S.A. with the latest materials and technology in gasket production to Vertex specifications. Vertex gaskets ensure long-lasting performance and leak prevention for your rebuild needs. Vertex's replacement gaskets and seals are available as top-end kits, complete engine kits, or as an oil seal kit.

• These sets include the head, base, and exhaust gaskets, valve seals, O-rings and other gaskets to complete a top-end rebuild.

For 100 years, Philips has been at the forefront of the automotive lighting industry, introducing technological innovations that have become standard on modern automobiles. Today, one in two cars in Europe and one in three worldwide is equipped with Philips lighting.

Nominal Voltage: 12 volts

NOTE: This Vertex Top End Gasket Set contains all components pictured.

Produced in the U.S.A. with the latest materials and technology in gasket production to Vertex specifications. Vertex gaskets ensure long-lasting performance and leak prevention for your rebuild needs. Vertex's replacement gaskets and seals are available as top-end kits, complete engine kits, or as an oil seal kit.

• These sets include the head, base, and exhaust gaskets, valve seals, O-rings and other gaskets to complete a top-end rebuild.

This convenient Denali lighting kit combines several high-quality Denali components including a wiring harness, light mount, and lights. It's designed to give you everything you need to equip your machine with an improved lighting setup and illuminate your riding experience.

Kit contains:

1x DENALI 2.0 PREMIUM WIRING HARNESS KIT (REV08) (SKU: DEDNLWHS10900)

1x DENALI ENG GUARD/CRASHBAR LIGHT MNT/ 21-29MM DIAM TUBES BLK (SKU: DELAH0010300B)

2x DENALI D4 LED LIGHT POD - DATADIM™ TECHNOLOGY - SINGLE (SKU: DEDNLD4050)

DENALI 2.0 PREMIUM WIRING HARNESS KIT (REV08) details:

This DENALI Premium Wiring Harness features high-quality waterproof components and is designed to power two DENALI LED Light Pods. It features low-profile, water-tight connectors and premium moulded wire to ensure moisture is kept out of the system. The harness includes a completely sealed, waterproof switch that was engineered from the ground up to withstand harsh out-door abuse on powersports vehicles. It’s clever design can be either flush or bar mounted.

What’s In The Box?

• (x1) Premium Wiring Harness
• (x1) Single-Intensity Relay
• (x1) DrySeal™ ON-OFF Waterproof Illuminated Switch
• (x1) 7/8 inch Handlebar Switch Mount
• (x1) 1 inch Handlebar Switch Mount
• (x2) Self Tapping Screw
• (x1) Adhesive Pad
• (x4) Zip Ties

DENALI ENG GUARD/CRASHBAR LIGHT MNT/ 21-29MM DIAM TUBES BLK details:

DENALI Universal Crashbar / Engine Guard Mount

This DENALI Bar Camp Light Mount Kit allows fitment of any DENALI LED Lights to engine guards, crash bars, or any tube 21mm-29mm (0.826in-1.125in) in diameter. These light mounts have a unique octagonal inner profile that allow the clamps to securely grip a wide range of tube diameters and include an optional, fully rotatable mounting shelf to create a super versatile and robust light mounting solution.

These clamps are intended for mounting lights to OEM or aftermarket crash bars, handlebars and frame tubes commonly found on adventure bikes, dual sport bikes, ATVs and snowmobiles. The clamps allow the lights to be positioned to the inside of the bars, ensuring they will be protected in a tip over.

Features

• Adjustable grip range (21mm-29mm) (0.826in-1.125in)
• Rotatable mounting shelf allows 4th axis of adjustability
• Lights can be mounted to shelf or directly to clamp
• Accepts M8 bolt from light pod
• Billet aluminum with black anodized finish
• Fits all standard SW-MOTECH, R&G, Givi, Kappa, Hepco-Becker, Krauser, Touratech, and BMW original crashbars
• Sold as pair

What's In The Box?

• (x2) Mounting clamps
• (x2) Rotatable mounting shelves
• (x1) Hardware Kit

DE NALI D4 LED LIGHT POD - DATADIM™ TECHNOLOGY - SINGLE details:

Simply put; the DENALI D4 is a beast. It is DENALI’s most powerful light packing the punch of 4380 lumens in an aggressively styled housing. The installed hybrid lens is equipped with two elliptical flood lenses and two spot beam lenses to create the ultimate hybrid beam pattern; a super wide close-range flood and a piercing spot beam in one housing. The included spot lens throws a massive beam of light and carries an official E-Mark certification.

D4 Pod Features

• High-Intensity Series Cree LEDs outputting 4380 lumens per pod
• DrySeal™ Submersible Waterproof light can withstand the most extreme environments
• LiveActive™ Thermal Management keeps the LEDs cool preventing the loss of light output from overheating
• Low profile mounting bracket with stainless steel hardware included
• Additional E-Mark Approved flood lens included
• Amber lenses available (sold separately) DNL.D4.10100

D4 Pod Specs

D4 Pod - What’s In The Box?

PH Series Brake Pad
SINTERED STREET BIKE PADS

NOT for Highway use

These long-lasting pads have a HH friction rating and are TUV tested and ECE R90 type approved.
Long- lasting and work well in either wet or dry riding.

Street Sport "Sintered"
High-performance HH friction-rated sintered metal pads made in the USA to an exclusive Premier formulation. The "PH" brake pads offer maximum durability and unbeatable performance under heavy braking and high-speed use.

For off-road use select the "PR" range for MX and ATV applications.

Reminder: one set of brake pads services one brake disc, if you are servicing multiple discs you will need multiple sets of brake pads.

Each pack of Premier CSK Clutch Springs contains a complete set of heavy-duty springs. Up to 15% stronger than the original.

Customer should be advised that after installation of a CSK kit the clutch lever will feel slightly ‘heavier’ than standard

Why use the SPLYT Technology?

As featured by Dirt Trax Television, RMSTATOR SPLYT Technology provides a reliable solution to well-known charging system failures. Using a dual output stator with two completely separate stator windings, this system splits the power generated by the stator into two separate voltage regulators. These regulators then each operate with only half of the load of the original system, allowing them to maintain a lower temperature and increase reliability.

SERIES Voltage Regulation

This system uses a new type of voltage regulator called a SERIES regulator. Rather than shunting excess power to ground like a typical regulator, it protects the battery from high voltage by disconnecting the stator coils from the regulator and preventing current from passing on. This type of voltage regulation generates less heat because current from the stator is prevented from flowing through the regulator.

Ultimate reliability

With a stock charging system, voltage regulators are consistently operating within 5% of their maximum capacity, leading to heat and stress related failure. With the RMSTATOR SPLYT system, both SERIES voltage regulators are operating with 40% overhead for long life and stable output.

Better design

Contrary to the original OEM stator that uses one three phase stator winding, the SPLYT stator contains two completely separate three-phase coil windings. Each of these two windings then produces half of the power of the stock stator lowering the temperature in each individual coil.

More available power

If you are installing a lot of accessories and electronics on your vehicle, like extra lighting, stereos or a winch,
the SPLYT kit is available with an improved flywheel designed to increase power output from 650 Watts to 900 Watts.

Easy to install

All parts use a Plug-and- Play design, just like the original OEM ones, so no special tool or knowledge is needed to install this system.

Harnesses included

Relocation wiring harnesses allow to relocate the regulators anywhere on your vehicle to get better air flow and easier access.

This kit includes:

• Dual output stator
• Two SERIES voltage regulators
• Improved high output flywheel
• Two automotive grade relocation wiring harnesses with OEM- quality heavy-duty connectors
• Gasket
• Complete instructions for voltage regulator relocation

Dual Output Stator Dimensions
Interior diameter : 53 mm
Exterior diameter : 125 mm
Thickness : 26 mm
Length of wires Stator to grommet : 125 mm
Length of wires grommet to plug : 290 mm & 550 mm

Other specifications :
Number of wires : 6
Number of plugs : 2
Number of pins : 6
Number of poles : 18

Wire to wire resistance :
Alternator: Yellow/Black to Yellow/Black = 0.5 ohms +- 20%

Regulator Dimensions
Width: 84 mm
Length: 90 mm
Height: 32 mm
Fixation holes center to center: 69 mm

Other specifications:
Number of plugs: 2
Number of pins: 5
Minimum Charging Voltage: 14.5 V +- 0.5 V
Maximum Charging Current: 50 A / 500 W
Open Circuit Voltage: < 15 V
Operation Temperature: -20º to 85º

Relocation Harness
Wires length : 3400 mm
Number of yellow wires : 3
Number of red wires : 1
Number of black wires : 1
Number of plugs : 2

Flywheel Dimensions
Exterior Diameter: 140.6 mm
Interior Diameter: 127.8 mm
Interior Diameter Center Housing: 22.4 mm
Exterior Diameter Center Housing: 50 mm
Thickness (exterior): 49.3 mm
Thickness (interior): 38.7 mm

Diameter of the Shaft largest to the narrowest:

• 37.4 mm
• 27.8 mm
• 22.4 mm

Each bike manufacturer uses different connectors for their indicators. This means that when fitting universal aftermarket indicators you need to cut the original connectors off and replace them with bullet fittings.

Not any more! Simply connect the IndyLeads between the original connector and the universal connector. Simple.

2 pack for front OR rear.

Oxford’s huge range of products encompasses everything that makes life on bikes better: from jackets, pants and boots to accessories, hard parts, locks, luggage and much more! Their market-leading products are designed in- house by a team of active enthusiasts and skilled technicians, based at the company’s 100,000 square-foot purpose-built headquarters in Oxfordshire, UK. With the support of the latest CAD technology, a 3D printing suite and a fully equipped test laboratory, Oxford innovate, analyse, test and develop unique products in pursuit of the best experience for two-wheel enthusiasts.

The Oxford Indicator Spacers cover holes left by standard-sized indicators in your motorcycle's fairing. Sold as a pair for both the left and right spacers, if requiring spacers for the front and rear you will need two packs. The indicator spacers are designed to ensure the perfect fit for Oxfords diverse range of indicators when replacing your broken, damaged or malfunctioning OEM indicators.

Yamaha Chain Slider bolts.

• 255g each.
• Cast carbon steel construction.
• Stylish gloss black design.
• Twin expanding TPR bungs for double damping and perfect balance.
• Fit handlebars from 13mm-18mm internal diameter.

• Direct OEM replacement at a fraction of the cost
• Includes valve, hose, gaskets, screws, clamps and everything needed to replace the OEM petcock
• Viton rubber fuel resistant gaskets
• Includes OE style fuel line and clamps

VERTEX TOP END ENGINE REBUILD KIT

Easing the repair process by saving time and money Vertex Pistons Top-End Piston Kits come with everything needed to replace your piston, top-end gaskets, and wrist pin bearing (for two-strokes) when the time comes. Included are the piston, rings, wrist pin, circlips, top end gaskets, and even wrist pin bearing (for two-stroke applications). Four-stroke kits include a free Camchain!

VERTEX Piston Features

Manufactured in Italy,Vertex, the premier brand of OEM replacement pistons, is the OEM supplier to KTM and numerous European motorcycle and go-kart manufacturers. Vertex offers enthusiasts state-of-the-art, high-quality pistons for nearly any powersport use from motorcycles and ATVs to marine and karting. Manufactured to the highest standards in Japan, Vertex’s piston rings are produced by the OEM suppliers so that they are direct OEM replacements. Vertex is the choice of those who truly seek the optimum in powersport performance in any application.

VERTEX Wrist Pin Features

Case hardened wrist pins are used with all Vertex pistons.Nitride coated pins are normally used for high performance four-stroke engines utilizing a bronze bushing or with engines using a steel connecting rod without bearings. This hardened surface is highly wear resistant and provides anti-galling properties. Nitriding is a highly specialized surface treatment that produces a highly wear resistant surface. The significant advantage of nitriding is that the surface hardness is developed without quenching and the attendant distortion problems with case hardening. Finishing operations can be eliminated or held to a minimum.

Features a black PVC outer jacket for maximum flexibility and durability, steel inner casing that is tightly coiled for low compression, pre-lubricated nylon inner sleeve, bird-caged wire ends, EPDM moulded rubber for high UV resistance and injection moulded components manufactured from high-strength POM material.

Features:

• Flexible and durable with steel inner casing that is tightly coiled for low compression.
• Pre-lubricated nylon inner sleeve.
• Bird caged wire ends.
• EPDM moulded rubber for high UV resistance and injection moulded components made from high-strength POM material.

Note: Kit contents may vary by fitment and are subject to change.

Replacing the fuel tank seal or gasket is a vital part of the fuel pump replacement process. Quantum tank seals are made exclusively from Viton, which are impervious to ethanol and other chemicals that degrade conventional rubber over time. These OE replacements are designed for fitment on specific vehicles.

Quality carburettor rebuild kit from All Balls.

• Kits include all of the necessary components to repair a carburettor. ATV models with two carburettors include components to repair two carburettors.
• Kit includes necessary all O-rings, gaskets, jets, needle, mixture screw, float bowl screws, float valve needles and seat. (Needle jet and other pressed-in jets are not included in the kit.)
• OEM jet sizes are included in the kit. NBR rubber material is used on all O-rings and rubber gaskets NBR has excellent resistance to the ethanol used in today’s fuels.
• Applications that use paper float bowl gaskets are upgraded to High-Performance Interface Gasket material.
• Components included in the kits are based on US models and discretion must be used when attempting to install the kit on a non-US model.
• Off-road use only.

NOTE: This complete Vertex Gasket Set contains all parts as pictured.

Produced in the U.S.A. with the latest materials and technology in gasket production to Vertex specifications. Vertex gaskets ensure long-lasting performance and leak prevention for your rebuild needs. Vertex's replacement gaskets and seals are available as top-end kits, complete engine kits, or as an oil seal kit.

• One kit containing all of the gaskets, O-rings, and valve seals necessary to rebuild the entire engine and transmission.
• Includes transmission seals.