New Arrivals

• Triple lip rubber seals keep the grease in and the water and dirt out., Chevron SRI 2 grease contains rust and oxidation inhibitors (-29° C-177° C)
• Double lip type TC seals with stainless steel garter springs.-Transmission seal kit-Double lip type TC seals with stainless steel garter springs

Kit Contents:

• (2) O'Ring
• (1) O'Ring
• (2) O'Ring
• (1) O'Ring
• (1) O'Ring
• (1) O'Ring
• (1) Seal
• (4) Seal

Replacing the fuel tank seal or gasket is a vital part of the fuel pump replacement process. Quantum tank seals are made exclusively from Viton, which are impervious to ethanol and other chemicals that degrade conventional rubber over time. These OE replacements are designed for fitment on specific vehicles.

High-quality crankshaft oil seals that are sold in a set.

Features:

• Replace OE originals exactly for proper fit and secure seal.
• Double lip seals with PTFE contact area tolerate dry start conditions with less crankshaft pin wear.

Notify: Verify part fitment before purchasing.

Wossner is Germany's finest aftermarket forged piston and rod manufacturer and have over 25 years of experience in the high- performance racing industry. Top European racers and FIM World Champions rely on Wossner for only the best pistons, rods and customer service.

Features:

• In-house designed and manufactured; all forgings are produced in Wossner's company-owned forging operation.
• 4-stroke pistons are made using a double-bridged forging design.
• Lightweight pistons with the tightest piston-wall clearances in the industry give you a quieter running engine.
• Wossner pistons are used by leading Supercross, Arenacross and MX GP teams.
• Made in Germany

Specifications:

• Pis ton Size: 87.97mm
• Oversize: Standard

NOTE: Wossner Piston Kits include the Piston, Wrist Pin, Circlips and Rings. Needle Bearings are not included.

Kit includes water pump cover gasket or o-ring, water pump shaft bearing(s) and seal(s) to repair a leaking water pump seal and/or a failed bearing.

Features:

• Precision micro bearings provide OE quality and durability.
• High pressure/temperature mechanical and rubber seals.

Quality carburettor rebuild kit from All Balls.

• Kits include all of the necessary components to repair a carburettor. ATV models with two carburettors include components to repair two carburettors.
• Kit includes necessary all O-rings, gaskets, jets, needle, mixture screw, float bowl screws, float valve needles and seat. (Needle jet and other pressed-in jets are not included in the kit.)
• OEM jet sizes are included in the kit. NBR rubber material is used on all O-rings and rubber gaskets NBR has excellent resistance to the ethanol used in today’s fuels.
• Applications that use paper float bowl gaskets are upgraded to High-Performance Interface Gasket material.
• Components included in the kits are based on US models and discretion must be used when attempting to install the kit on a non-US model.
• Off-road use only.

The S3 sintered compound is optimal for street bikes, dual sport, touring, cruisers. It's recommended on applications with rather larger engines or for people who ride harder than average and want the great stopping power of a sintered brake pad.

The S3 series is designed for low abrasive interaction with the rotor and quieter braking because the ceramic composite material. It has an HH friction rating and performs better at higher temperatures than our AD compound.

Friction materials contain metal-ceramic with a bronze-graphite and non-metallic friction additives are spread evenly on the base fine bronze body to achieve optimal friction properties.

Features:

• Very high static friction coefficient.
• Minimal difference between wet and dry braking performance.
• Good abrasive resistance.
• Thermal stability up to 450°C, and even up to 800°C over a short term.
• Low abrasive interaction with the brake rotor material.
• Longer life compared to organic and kevlar composite materials.

Application:

• Rec ommended for larger street bikes.
• For riders who demand a bit more than average from their bikes.
• Recommended on both front and rear brakes.
• Works well on both dry and wet conditions.
• Could also be used on the front brakes for off-road bikes and ATV.

Carburetor repair kits
• Kits include all of the necessary components to repair a carburetor. ATV models with two carburetors include components to repair two carburetors.
• Kit includes necessary all O-rings, gaskets, jets, needle, mixture screw, float bowl screws, float valve needle and seat. (Needle jet and other pressed in jets are not included in kit.)
• OEM jet sizes are included in the kit. NBR rubber material is used on all O-rings and rubber gaskets NBR has excellent resistance to the ethanol used in today’s fuels.
• Applications that use paper float bowl gaskets are upgraded to High Performance Interface Gasket material.
• Components included in the kits are based off of US models and discretion must be used when attempting to install the kit on a non US model.
• Off road use only.

Buy together and save! Our Disc and Pad kits include an MTX Brake Disc and GOLDfren Brake Pad set for your motorcycle or ATV.

The included discs are constructed using one complete segment of Japanese SUS 420 stainless steel, then heat-treated to HRC 36+-2. Meanwhile, the included pad is designed for low abrasive interaction with the rotor, long life and self-cleaning capabilities necessary in diverse riding conditions.

GOLDfren began manufacturing sintered disc brake pads for a wide range of off-road and road motorcycles in 1991, nearly three decades on from their first motorcycle brake pads GOLDfren has become one of the largest aftermarket manufacturers in the motorcycle brake disc pad industry. Their development of next-generation products has kept them at the technological forefront of Sintered Friction Braking providing you with confidence in the performance, durability and reliability of your brakes.

S3 Series:

The S3 sintered compound is optimal in dry and wet conditions for road & off-road motorcycles. For the road application, S3 pads are suitable for both the front and rear brake while on off-road applications the S3 is only recommended for the front brake. The S3 series is designed for low abrasive interaction with the rotor and quieter braking due to the ceramic composite material. It has an HH friction rating and performs better at higher temperatures than the AD compound. Friction materials contain metal-ceramic with a bronze-graphite and non-metallic friction additives are spread evenly on the base fine bronze body to achieve optimal friction properties.

Features:

• Very high static friction coefficient
• Minimal difference between wet and dry braking performance
• Good abrasive resistance
• Low abrasive interaction with the brake rotor material
• Longer life compared to organic and Kevlar composite materials

Application:

• For riders who demand a bit more than average from their bikes
• Recommended on both front and rear brakes (road application)
• Can also be used on the front brakes of off-road bikes and ATVs
• Works well on both dry and wet conditions

Operating Parameters:

• Specific pressure: 3.0 Mpa
• Sliding speed: 45 m/s
• Constant maximum temp: 450°C
• Short time maximum temp: 800°C
• Counter-surfaces: steel disks

What is a sintered brake pad?

GOLDfren only manufacturers sintered brake pads that contain metal-ceramic and ceramic-carbon friction materials, these materials allow for less brake dust and a quieter braking experience. Sintered brake pads are made by fusing together metallic particles under high temperature and pressure which enhances friction properties and pad life, resulting in longer life and stronger braking. Sintered brake pads experience no brake fade when operating at high temperatures and in wet conditions. They also last up to 5 times longer than organic pads and provide additional braking strength. All materials used are environmentally friendly and do not contain any lead, asbestos, fibreglass or formaldehyde.

Reminder: one set of brake pads services one brake disc, if you are servicing multiple discs you will need multiple sets of brake pads.

RMSTATOR is specialized in designing and manufacturing innovative electrical and electronic components for Powersports vehicles like motorcycles, ATV, SxS, UTV, snowmobiles, and PWC. Through unrelenting quality control, we ensure that each component meets or exceeds the OEM specs. With over 25 product families, rest assured that you will find the part you need.

STOP BURNING YOUR REGULATOR RECTIFIER! It is time to update or replace your voltage regulator with RM STATORS advanced MOSFET technology. RM STATORS MOSFET Regulators run cooler than all OEM diode style regulators. In addition, this rectifier has overheat protection, rather than burn up it will simply turn off for a while and cool off.

• Direct replacement to your original unit
• Plug-and-play, direct fit, easy installation
• The quality exceeds the OEM equipment
• Improved heat sink and charging capabilities
• Higher grade of electric components

What are the advantages of the MOSFET Technology?

• Runs much cooler than the traditional Shunt voltage regulator rectifier
• Less load on the stator, less work, less fuel is used and you save
• The power charging your battery is steadier and smooth
• Extends the battery’s life and cold-cranking capacity
• Removes stator load resulting in more engine power
• Optimize power delivery by switching the stator coils on or off

NOTE: Battery condition is extremely important. No voltage regulator can work correctly with a bad or weak battery. Always fully charge your battery before performing any charging system tests or replacing parts. If there is any doubt, have the battery load tested or replaced.

Please Note:

1. All electrical components must be fitted by a qualified technician.
2. Before fitting electrical components ensure the root cause of the original failure has been addressed.
3. The absence of either of points 1 or 2 above, will void any warranty.

Brand new aftermarket 2-Positions Ignition Key Switch.

• Direct replacement to your original unit
• Plug-and-play, direct fit, easy installation
• Two keys included
• Connectors included
• All products shipped are tested

Dimensions:

• Height: 46 mm
• Length: 46 mm
• Width: 30,29 mm
• Wires length: 300 mm

Other Specifications:

• Number of wires: 4
• Number of plugs: 1
• Number of keys: 2
• Number of positions: 2 (off, on)

Kit includes case-hardened bushing, replacement outer seal along with any O-rings, snap rings or lock washers required to complete the repair.

Features:

• Hardened bushings reduce wear and seal damage.
• Upgraded seal material reduces bushing wear and increases life.
• Brushing coating reduces corrosion.

Note: Verify fitment before purchasing.

All the bearings and seal required to refit a wheel in one convenient package.

Features:

• Premium high-speed bearings feature low drag.
• Double lip seals on both sides to provide superior exclusion of water and dirt
• Improved grease retention.

The HFP-181 is a replacement external (frame mounted) fuel pump for carbureted motorcycle applications.  This pump kit provides the exact pressure and volume as required by Honda, Kawasaki, KTM, Suzuki, and Yamaha motorcycle applications.

• OEM or better performance
• Polished corrosion-resistant case to help minimize seizing during non-operation
• Specifically designed for quiet operation
• Drop-in replacement
• Gradient density fuel strainer for superior contaminant filtration
• Patented check valve technology
• Compatible with modern ethanol-infused pump gasoline

A 4-wire direct replacement frame-mounted electric fuel pump for motorcycle and powersports applications. Quantum replacement fuel pumps are designed to meet or exceed OEM specifications, and feature upgrades that improve on the OEM design. Upgraded polymers, brushes, and commutators ensure long life and durability in multiple fuel blends.

Features:

• OEM or better performance.
• Gradient density fuel strainer for superior contaminant filtration.
• Polished corrosion-resistant case to help minimise seizing during non-operation.
• Specifically designed for quiet operation.
• Drop-in replacement.
• Patented check valve technology.
• Compatible with modern ethanol-infused pump gasoline.

K&N 99-0516 is a 12.25-ounce aerosol can of air filter oil. K&N Air Filter Oil is the only oil specially formulated to work in combination with the cotton fabric in K&N air filter elements, providing a superior air filtration system. When used as directed, it quickly penetrates the filter pleats, where it remains suspended in the cotton fabric. Saturation is maintained until the element is cleaned with K&N Air Filter Cleaner.

Features:

• The only oil designed specifically for K&N filters.
• Specially formulated to improve air filter performance.
• Quickly penetrates and saturates the filter pleats.
• 12.25-ounce (362ml) aerosol spray can for convenient spray-on use.

• Direct OEM replacement at a fraction of the cost
• Includes valve, hose, gaskets, screws, clamps and everything needed to replace the OEM petcock
• Viton rubber fuel resistant gaskets
• Includes OE style fuel line and clamps

PH SERIES – Street Sport Sintered

High-performance HH friction rated sintered metal pads made in the USA to an exclusive Premier formulation. PH brake pads offer maximum durability and unbeatable performance under heavy braking and high-speed use. PH series is no longer available for off-road applications following the formulation improvements of the PR range for Moto-X and ATV applications.

Rough riding calls for stronger axles and that’s where All Balls Racing excels. Machined for exact OEM fit, the shaft is made of chromoly steel with a larger diameter than most axles. The axle has 6 ball bearings in each CV joint. Laminate coating resists corrosion and rust and protects axles from dirt, water, rocks and grease. Waterproof neoprene boots act as a first line of defence, shielding vulnerable joints and preventing leaks. High-performance molybdenum grease reduces heat and friction.

In static torsion trials, these axles were up to 30% stronger than OEM and aftermarket competition.

Features:

• 40% stronger than OEM.
• Larger 4340 chrome-moly steel axle bar.
• Precision ground components.
• Low profile clamps.
• Lasts approximately 50 percent longer than many aftermarket competitors.
• Neoprene boots.
• Typically runs almost 130,000 cycles versus 80,000 cycles for many axles.
• Engineered in the USA.
• Manufactured in an ISO facility.Assembled with 3% molybdenum grease.

Each pack of Premier CSK Clutch Springs contains a complete set of heavy-duty springs. Up to 15% stronger than the original.

Customer should be advised that after installation of a CSK kit the clutch lever will feel slightly ‘heavier’ than standard

Wossner is Germany's finest aftermarket forged piston and rod manufacturer and have over 25 years of experience in the high-performance racing industry. Top European racers and FIM World Champions rely on Wossner for only the best pistons, rods, and customer service.

Diameter: 54mm

Note: This includes ONE Piston Ring and some fitments may require two rings.

Please Note:

1. All electrical components must be fitted by a qualified technician.
2. Before fitting electrical components ensure the root cause of the original failure has been addressed.
3. The absence of either of points 1 or 2 above, will void any warranty.

NOTE: This complete Vertex Gasket Set contains all parts as pictured.

Produced in the U.S.A. with the latest materials and technology in gasket production to Vertex specifications. Vertex gaskets ensure long-lasting performance and leak prevention for your rebuild needs. Vertex's replacement gaskets and seals are available as top-end kits, complete engine kits, or as an oil seal kit.

• One kit containing all of the gaskets, O-rings, and valve seals necessary to rebuild the entire engine and transmission.
• Includes transmission seals.

Each pack of Premier CSK Clutch Springs contains a complete set of heavy-duty springs. Up to 15% stronger than the original.

Customer should be advised that after installation of a CSK kit the clutch lever will feel slightly ‘heavier’ than standard

Upgrade your motorcycle's clutch system with the All Balls Racing Motorcycle Clutch Cable. Designed with precision and durability in mind, this clutch cable delivers exceptional performance and reliability on the road.

• Black PVC outer jacket for maximum flexibility and durability.
• Steel inner casing that is tightly coiled for low compression.
• A pre-lubricated nylon inner sleeve guarantees smooth operation and long life.
• All wire ends are bird-caged prior to terminal casting for superior pull-out resistance.
• EPDM-moulded rubber components for high UV resistance and long life.
• Injected moulded components are manufactured from high-strength POM material.

Please Note:

1. All electrical components must be fitted by a qualified technician.
2. Before fitting electrical components ensure the root cause of the original failure has been addressed.
3. The absence of either of points 1 or 2 above, will void any warranty.