STEERING & SUSPENSION

Rough riding calls for stronger axles and that’s where All Balls Racing excels. Machined for exact OEM fit, the shaft is made of chromoly steel with a larger diameter than most axles. The axle has 6 ball bearings in each CV joint. Laminate coating resists corrosion and rust and protects axles from dirt, water, rocks and grease. Waterproof neoprene boots act as a first line of defence, shielding vulnerable joints and preventing leaks. High-performance molybdenum grease reduces heat and friction.

In static torsion trials, these axles were up to 30% stronger than OEM and aftermarket competition.

Features:

• 40% stronger than OEM.
• Larger 4340 chrome-moly steel axle bar.
• Precision ground components.
• Low profile clamps.
• Lasts approximately 50 percent longer than many aftermarket competitors.
• Neoprene boots.
• Typically runs almost 130,000 cycles versus 80,000 cycles for many axles.
• Engineered in the USA.
• Manufactured in an ISO facility.Assembled with 3% molybdenum grease.

A Quality Swing Arm Repair Kit from All Balls Racing containing everything required to rebuild swing arm bearings. Confirm suitability for your year, make, model prior to purchase.

Bushings are case-hardened and plated to prevent wear and corrosion. POM composite washer bearings replace thrust needle washers for superior resistance to water and dirt and increase service life. Shafts are made from 52100 Bearing steel, through hardened and precision ground. Needle Bearings are made from 52100 bearing steel and ARC61-65 heat treated ST13 steel shell.

Kit Contents:

• 2x Washers
• 4x Seals
• 2x Needle Bearing Shaft
• 2x Needle Bearings
• 4x Bushings

Modern bikes are built to withstand extreme conditions, but suspension linkage bearings are often the first to wear out. Constant exposure to dust, mud, and moisture, followed by wet storage, accelerates wear and causes suspension slop. Restore your rear suspension's full performance with a high-quality All Balls Racing swingarm linkage bearing set.

Features:

• Replacement bearing kit for swingarm linkages.
• OEM quality parts at a fraction of the price.
• Kit includes bearings, seals and spacers needed for a full rebuild.

Quality design and construction of every All Balls piece meets the toughest standards and conditions - from daily commuting to full-on racing, all older bearing and seal designs are upgraded to the best and latest specs and designs.

Available individually in left-hand and right-hand thread or sold in pairs one L/H and one R/H thread.

KoubaLink specialises in motorcycle lowering and performance linkages for off-road and dual-sport rear suspension systems. Compromise is not an option at KoubaLink. Listening to riders from all over the world explain where and how they use their off-road and dual-sport bikes. With their input, Koubalink manufacture products that add to your motorcycling experience and make it a little more enjoyable.

• Provides better front-end stability by lowering rear suspension geometry
• Machined from billet aluminium
• Stronger than OEM
• Assembled using OE bearings and seals
• Replace linkage like its OEM
• Includes all required bearings and seals for assembly (Excluding Dog Bone styled linkages that do not include bearings and seals from factory)

Lowering amount varies by application:

• KAWASAKI KLX 300R 2020-2022 - 50.8mm
• KAWASAKI KLX 250R 1994-2022 - 57.15mm
• KAWASAKI KLX 300R 1994-2019 - 57.15mm

A quality Steering Head Bearing kit from All Balls. Make your bike handle like new!

Features:

• Upgrade ball-type steering bearings to Heavy-Duty Tapered Bearings
• Higher torque load and better wear than OEM ball-style steering bearings.
• Each kit is complete with upper and lower bearing sets and seals.

Quality design and construction of every All Balls piece meets the toughest standards and conditions - from daily commuting to full-on racing, all older bearing and seal designs are upgraded to the best and latest specs and designs.

Available individually in left-hand and right-hand thread or sold in pairs one L/H and one R/H thread.

A quality pair of fork oil and dust seals from All Balls Racing.

Features:

• Dyno tested to last 3 to 4 times longer than OEM seals.
• Directional ribs outside of the seal allow easy installation.
• Dual-sealing lips guarantee oil stays in and dirt stays out.

Kits contain components for greater suspension travel and performance.

Features:

• Needle bearing shafts are made with 52100 bearing steel that has been hardened and precision ground.
• Self lubricating Acetal nylon bushings for better wear and performance.
• All metal bushings are case-hardened and plated to prevent wear and corrosion.

• Dynamically balanced and phased as complete 2-piece (where applicable) assemblies by the manufacturer
• The complete driveline is balanced to reduce noise and vibration while extending its life
• Carrier bearing included (where applicable) – including the carrier bearing reduces cost, eases assembly, and provides a complete ready to install driveline
• Designed with the same dimensions as an OEM drive shaft for guaranteed fitment
• Greaseable u-joints allow maintenance of the driveshaft

The All Balls CV Boot material is compounded from an OEM grade DCR66 rubber that is formulated specifically for the demanding requirements of today’s ATVs and UTVs.

• 40% higher tensile strength than conventional CV boot material, suitable for the high joint angles of modern ATVs and UTVs.
• 50% more abrasion-resistant than conventional CV boot material to ensure a long life in harsh off-road environments.
• Rubber compound is tested to -40° F to ensure good performance and long life at low temperatures.
• Lithium-based Molybdenum Grease insures good lubrication for long CV joint life. Easier to install than most OEM and aftermarket boots. Sold each. Does not require the use of a "Banding Tool".

Kits include:

• Two stainless steel clamps that are designed to be tightened without the use of special tools.

A Quality Fork Bush from All Balls Racing. 

*This is just a single bush

Quality design and construction of every All Balls piece meets the toughest standards and conditions - from daily commuting to full-on racing, all older bearing and seal designs are upgraded to the best and latest specs and designs.

One kit does it all! All of the bearings, seals, shafts*, bushings, and thrust bearings (if required) in one all-inclusive kit to do the job correctly and completely.

• All bearing shafts manufactured with 52100 bearing steel that is hardened and centerless ground for a precision fit and extended wear life.
• Steel spacers are case-hardened and plated for resistance to wear and corrosion.
• No more hunting around for missing pieces costing you time and extra money.
• Needle thrust bearings have been replaced with Teflon bearings. Designed to live longer in water and dirt.

* Not included in all kits.

Note: A limited number of kits only available with bearings and seals.

KoubaLink specialises in motorcycle lowering and performance linkages for off-road and dual-sport rear suspension systems. Compromise is not an option at KoubaLink. Listening to riders from all over the world explain where and how they use their off-road and dual-sport bikes. With their input, Koubalink manufacture products that add to your motorcycling experience and make it a little more enjoyable.

Features:

• Provides better front-end stability by lowering rear suspension geometry.
• Machined from billet aluminium.
• Stronger than OEM.
• Pre-installed OE style bearings included.
• Replace linkage like its OEM.
• Includes all required bearings and seals for assembly (Excluding Dog Bone styled linkages that do not include bearings and seals from factory).

Quality design and construction of every All Balls piece meets the toughest standards and conditions - from daily commuting to full-on racing, all older bearing and seal designs are upgraded to the best and latest specs and designs.

One kit does it all! All of the bearings, seals, shafts*, bushings, and thrust bearings (if required) in one all-inclusive kit to do the job correctly and completely.

• All bearing shafts manufactured with 52100 bearing steel that is hardened and centerless ground for a precision fit and extended wear life.
• Steel spacers are case-hardened and plated for resistance to wear and corrosion.
• No more hunting around for missing pieces costing you time and extra money.
• Needle thrust bearings have been replaced with Teflon bearings. Designed to live longer in water and dirt.

* Not included in all kits.

Note: A limited number of kits only available with bearings and seals.

Designed to keep your differential in top condition, this kit includes high-quality seals that prevent leaks and protect against dirt, water, and debris. Easy to install and compatible with a wide range of ATV and UTV models, this differential seal kit provides a cost-effective solution to prevent costly repairs and downtime. Fit these and have peace of mind.

Features:

• Double lip type TC seals.
• Front or rear position sold separately.

Note: Contains seals only. Verify fitment before purchasing.

Rough riding calls for stronger axles and that’s where All Balls Racing excels. Machined for exact OEM fit, the shaft is made of chromoly steel with a larger diameter than most axles. The axle has 6 ball bearings in each CV joint. Laminate coating resists corrosion and rust and protects axles from dirt, water, rocks and grease. Waterproof neoprene boots act as a first line of defence, shielding vulnerable joints and preventing leaks. High-performance molybdenum grease reduces heat and friction.

In static torsion trials, these axles were up to 30% stronger than OEM and aftermarket competition.

Features:

• 40% stronger than OEM.
• Larger 4340 chrome-moly steel axle bar.
• Precision ground components.
• Low profile clamps.
• Lasts approximately 50 percent longer than many aftermarket competitors.
• Neoprene boots.
• Typically runs almost 130,000 cycles versus 80,000 cycles for many axles.
• Engineered in the USA.
• Manufactured in an ISO facility.Assembled with 3% molybdenum grease.

Up to 40% stronger than OE axles, these complete axles feature enlarged CV joints, bearing cages, and chromoly axle shafts. All internal components are precision ground and utilize molybdenum grease.

Features:

• 40% stronger than OEM.
• Larger 4340 chrome-moly steel axle bar.
• Precision ground components.
• Low profile clamps.
• Neoprene boots.
• Engineered in the USA.
• Manufactured in an ISO facility.
• Assembled with 3% moly grease.
• Black oxide coating to resist rust and corrosion.

Rough riding calls for stronger axles and that’s where All Balls Racing excels. Machined for exact OEM fit, the shaft is made of chromoly steel with a larger diameter than most axles. The axle has 6 ball bearings in each CV joint. Laminate coating resists corrosion and rust and protects axles from dirt, water, rocks and grease. Waterproof neoprene boots act as a first line of defence, shielding vulnerable joints and preventing leaks. High-performance molybdenum grease reduces heat and friction.

In static torsion trials, these axles were up to 30% stronger than OEM and aftermarket competition.

Features:

• 40% stronger than OEM.
• Larger 4340 chrome-moly steel axle bar.
• Precision ground components.
• Low profile clamps.
• Lasts approximately 50 percent longer than many aftermarket competitors.
• Neoprene boots.
• Typically runs almost 130,000 cycles versus 80,000 cycles for many axles.
• Engineered in the USA.
• Manufactured in an ISO facility.Assembled with 3% molybdenum grease.

A quality pair of fork oil and dust seals from All Balls Racing.

Features:

• Dyno tested to last 3 to 4 times longer than OEM seals.
• Directional ribs outside of the seal allow easy installation.
• Dual-sealing lips guarantee oil stays in and dirt stays out.

This heavy-duty ball joint kit is engineered for those who demand reliability and strength in their vehicle's components.

Features:

• Heavy-duty steel housing.
• POM-M90 bearing cup to isolate the ball end from the steel housing for longer life.
• Steel-on-steel design with an adjustable cap and a grease zerk.
• Adjustable end cap allows slop to be taken up as the ball joint wears.

Up to 40% stronger than OE axles, these complete axles feature enlarged CV joints, bearing cages, and chromoly axle shafts. All internal components are precision ground and utilize molybdenum grease.

Features:

• 40% stronger than OEM.
• Larger 4340 chrome-moly steel axle bar.
• Precision ground components.
• Low profile clamps.
• Neoprene boots.
• Engineered in the USA.
• Manufactured in an ISO facility.
• Assembled with 3% moly grease.
• Black oxide coating to resist rust and corrosion.

Rough riding calls for stronger axles and that’s where All Balls Racing excels. Machined for exact OEM fit, the shaft is made of chromoly steel with a larger diameter than most axles. The axle has 6 ball bearings in each CV joint. Laminate coating resists corrosion and rust and protects axles from dirt, water, rocks and grease. Waterproof neoprene boots act as a first line of defence, shielding vulnerable joints and preventing leaks. High-performance molybdenum grease reduces heat and friction.

In static torsion trials, these axles were up to 30% stronger than OEM and aftermarket competition.

Features:

• 40% stronger than OEM.
• Larger 4340 chrome-moly steel axle bar.
• Precision ground components.
• Low profile clamps.
• Lasts approximately 50 percent longer than many aftermarket competitors.
• Neoprene boots.
• Typically runs almost 130,000 cycles versus 80,000 cycles for many axles.
• Engineered in the USA.
• Manufactured in an ISO facility.Assembled with 3% molybdenum grease.

Upgrade rubber bushings found in Utility ATV A-Arms to AB's redesigned HD Delrin bushings.

This kit is designed to replace worn-out rubber bushings and provides greater suspension travel and performance.

Quality design and construction of every All Balls piece meet the toughest standards and conditions - from daily commuting to full-on racing, all older bearing and seal designs are upgraded to the best and latest specs and designs.

A quality Steering Head Bearing kit from All Balls. Make your bike handle like new!

Features:

• Upgrade ball-type steering bearings to Heavy-Duty Tapered Bearings
• Higher torque load and better wear than OEM ball-style steering bearings.
• Each kit is complete with upper and lower bearing sets and seals.