STEERING & SUSPENSION

Rough riding calls for stronger axles and that’s where All Balls Racing excels. Machined for exact OEM fit, the shaft is made of chromoly steel with a larger diameter than most axles. The axle has 6 ball bearings in each CV joint. Laminate coating resists corrosion and rust and protects axles from dirt, water, rocks and grease. Waterproof neoprene boots act as a first line of defence, shielding vulnerable joints and preventing leaks. High-performance molybdenum grease reduces heat and friction.

In static torsion trials, these axles were up to 30% stronger than OEM and aftermarket competition.

Features:

• 40% stronger than OEM.
• Larger 4340 chrome-moly steel axle bar.
• Precision ground components.
• Low profile clamps.
• Lasts approximately 50 percent longer than many aftermarket competitors.
• Neoprene boots.
• Typically runs almost 130,000 cycles versus 80,000 cycles for many axles.
• Engineered in the USA.
• Manufactured in an ISO facility.Assembled with 3% molybdenum grease.

Upgrade rubber bushings found in Utility ATV A-Arms to AB's redesigned HD Delrin bushings.
This kit is designed to replace worn out rubber bushings and provides greater suspension travel and performance.
Quality design and construction of every All Balls piece meets the toughest standards and conditions - from daily commuting to full-on racing, all older bearing and seal designs are upgraded to the best and latest specs and designs.

Constructed from heat-treated steel for maximum durability and strength while designed to be compatible with your stock components. The solid axle design gives consistent, relatively unchanging ground clearance with a lower rolling centre which decreases the likelihood of rolling. Fewer moving parts reduce the chance of a breakdown, while also making an easier job out of routine maintenance.

• Direct bolt in replacement for OEM axle.
• Meets or exceeds oem specifications.
• Quality heavy duty construction.

A quality Steering Head Bearing kit from All Balls. Make your bike handle like new!

Features:

• Upgrade ball-type steering bearings to Heavy-Duty Tapered Bearings
• Higher torque load and better wear than OEM ball-style steering bearings.
• Each kit is complete with upper and lower bearing sets and seals.

These fork seal kits are manufactured to OEM specifications and tolerances to guarantee quality and superior durability. Dust seals feature external garter springs to keep the fork tubes clean from dust and grime.

Features:

• Dyno tested to last 3 to 4 times longer than OEM seals.
• Directional ribs on outside of seal allow seal to be installed easily.
• Dual sealing lips guarantee oil stays in and dirt stays out.

Quality design and construction of every All Balls piece meets the toughest standards and conditions - from daily commuting to full-on racing, all older bearing and seal designs are upgraded to the best and latest specs and designs.

Available individually in left-hand and right-hand thread or sold in pairs one L/H and one R/H thread.

Kit contains direct OEM replacement bearing assembly with all the required components.

• Shock-bearing assemblies are sold individually for the upper or lower position.
• Plastic moulded bushings upgraded to machined Delrin.
• Mild steel pins upgraded to case hardened and precision ground SCM415/42 bearing steel.
• Many times, OEM manufacturers do not sell the components separately from the shock absorber.
• Where possible and applicable, we have added an o-ring to the ID of Delrin machined bushings for superior water and dirt exclusion.

Trusted by riders and dealers in the automotive market, the Whites CV Axle proves its durability against the industry's top manufacturers. With oversized outer joints accommodating up to a 45° swing angle, it enhances suspension travel and robustness. Through the latest CNC manufacturing technologies, the inner joints allow up to 45° of movement. Enhanced by high-strength TPE boots, OTK clamps, and moly grease, it delivers optimal performance in harsh conditions, significantly extending axle lifespan.

• Up to 45° swing angle.
• Up to 45° travel on inner joints.
• Best quality OTK clamps.
• Longer lasting, higher strength TPE boots.
• Moly grease for reliable performance.

Please refer to our online fitment guide for regular additions to the range and specific fit for your model.

Proven to perform in the extremes of our local terrain, Whites CV Axles are produced alongside the world's biggest brands in the ATV/UTV market.

Our hard-wearing axles feature oversized outer joints that allow generous levels of swing angle, providing increased suspension travel and strength. The latest CNC manufacturing processes are utilised to allow excellent levels of travel on the inner joints.

The higher strength and longer lasting TPE boots, OTK clamps and moly grease provide the best performance in extreme conditions and extend the life of your axle.

Features:

• Generous levels of swing angle.
• Excellent levels of travel on the inner joints.
• Best quality OTK clamps.
• Longer lasting, higher strength TPE boots.
• Moly grease for reliable performance.

Note:

• Axle boots are available to suit this axle:
  • Inner: WPAXCVB013
  • Outer: WPAXCVB014
• Please confirm suitability for your year, make, and model prior to purchase.

Rough riding calls for stronger axles and that’s where All Balls Racing excels. Machined for exact OEM fit, the shaft is made of chromoly steel with a larger diameter than most axles. The axle has 6 ball bearings in each CV joint. Laminate coating resists corrosion and rust and protects axles from dirt, water, rocks and grease. Waterproof neoprene boots act as a first line of defence, shielding vulnerable joints and preventing leaks. High-performance molybdenum grease reduces heat and friction.

In static torsion trials, these axles were up to 30% stronger than OEM and aftermarket competition.

Features:

• 40% stronger than OEM.
• Larger 4340 chrome-moly steel axle bar.
• Precision ground components.
• Low profile clamps.
• Lasts approximately 50 percent longer than many aftermarket competitors.
• Neoprene boots.
• Typically runs almost 130,000 cycles versus 80,000 cycles for many axles.
• Engineered in the USA.
• Manufactured in an ISO facility.Assembled with 3% molybdenum grease.

7-blade radiator fan wheel from All Balls.

Specifications:

• Wheel outside diameter (OD): 208 mm (8.189")
• Wheel thickness: 32.2 mm (1.268")

Quality design and construction of every All Balls piece meets the toughest standards and conditions - from daily commuting to full-on racing, all older bearing and seal designs are upgraded to the best and latest specs and designs.

One kit does it all! All of the bearings, seals, shafts*, bushings, and thrust bearings (if required) in one all-inclusive kit to do the job correctly and completely.

• All bearing shafts manufactured with 52100 bearing steel that is hardened and centerless ground for a precision fit and extended wear life.
• Steel spacers are case-hardened and plated for resistance to wear and corrosion.
• No more hunting around for missing pieces costing you time and extra money.
• Needle thrust bearings have been replaced with Teflon bearings. Designed to live longer in water and dirt.

* Not included in all kits.

Note: A limited number of kits only available with bearings and seals.

Rough riding calls for stronger axles and that’s where All Balls Racing excels. Machined for exact OEM fit, the shaft is made of chromoly steel with a larger diameter than most axles. The axle has 6 ball bearings in each CV joint. Laminate coating resists corrosion and rust, and protects axle from dirt, water, rocks and grease. Waterproof neoprene boots act as a first line of defense, shielding vulnerable joints and preventing leaks. High-performance molybdenum grease reduces heat and friction.

• In static torsion trials, these axles were up to 30% stronger than OEM and aftermarket competition.
• Lasts approximately 50 percent longer than many aftermarket competitors.
• Typically runs almost 130,000 cycles versus 80,000 cycles for many axles.

Features:

• 40% stronger than OEM.
• Larger 4340 chrome-moly steel axle bar.
• Precision ground components.
• Low profile clamps.
• Neoprene boots.
• Engineered in the USA.
• Manufactured in an ISO facility.
• Assembled with 3% molybdenum grease.

Designed to keep your differential in top condition, this kit includes high-quality seals that prevent leaks and protect against dirt, water, and debris. Easy to install and compatible with a wide range of ATV and UTV models, this differential seal kit provides a cost-effective solution to prevent costly repairs and downtime. Fit these and have peace of mind.

Features:

• Double lip type TC seals.
• Front or rear position sold separately.

Note: Contains seals only. Verify fitment before purchasing.

Quality design and construction of every All Balls piece meets the toughest standards and conditions - from daily commuting to full-on racing, all older bearing and seal designs are upgraded to the best and latest specs and designs.

Available individually in left-hand and right-hand thread or sold in pairs one L/H and one R/H thread.

The All Balls CV Boot material is compounded from an OEM grade DCR66 rubber that is formulated specifically for the demanding requirements of today’s ATVs and UTVs.

• 40% higher tensile strength than conventional CV boo material, suitable for the high joint angles of modern ATVs and UTVs.
• 50% more abrasion-resistant than conventional CV boot material to ensure a long life in harsh off-road environments.
• Rubber compound is tested to -40° F to ensure good performance and long life at low temperatures.
• Lithium-based Molybdenum Grease insures good lubrication for long CV joint life. Easier to install than most OEM and aftermarket boots. Sold each. Does not require the use of a ""Banding Tool"".

Specifications:

• H: 94mm
• SD: 17mm
• LD: 65.5mm
• Shaft I.D.: 17
• CV Body I.D.: 65.5
• Leng 94

Kits include:

• Two stainless steel clamps that are designed to be tightened without the use of special tools.

Upgrade rubber bushings found in Utility ATV A-Arms to AB's redesigned HD Delrin bushings.
This kit is designed to replace worn out rubber bushings and provides greater suspension travel and performance.
Quality design and construction of every All Balls piece meets the toughest standards and conditions - from daily commuting to full-on racing, all older bearing and seal designs are upgraded to the best and latest specs and designs.

The All Balls CV Boot material is compounded from an OEM grade DCR66 rubber that is formulated specifically for the demanding requirements of today’s ATVs and UTVs.

• 40% higher tensile strength than conventional CV boo material, suitable for the high joint angles of modern ATVs and UTVs.
• 50% more abrasion-resistant than conventional CV boot material to ensure a long life in harsh off-road environments.
• Rubber compound is tested to -40° F to ensure good performance and long life at low temperatures.
• Lithium-based Molybdenum Grease insures good lubrication for long CV joint life. Easier to install than most OEM and aftermarket boots. Sold each. Does not require the use of a ""Banding Tool"".

Specifications:

• H: 84mm
• SD: 17mm
• LD: 54.5mm
• Shaft I.D.: 17
• CV Body I.D.: 54.5
• Leng 84

Kits include:

• Two stainless steel clamps that are designed to be tightened without the use of special tools.

Hands down, the most complete line of swing arm bearing and seal kits!

Kit contains all of the components required to properly rebuild the swing arm bearing assembly.

Needle bearing shafts are made with SCM415/42 bearing steel that has been hardened and precision ground.

All metal bushings are case-hardened and plated to prevent wear and corrosion.

Includes:

• Needle Bearing Shaft (4x)
• Needle Bearing (4x)

Proven to perform in the extremes of our local terrain, Whites CV Axles are produced alongside the world's biggest brands in the ATV/UTV market.

Our hard-wearing axles feature oversized outer joints that allow generous levels of swing angle, providing increased suspension travel and strength. The latest CNC manufacturing processes are utilised to allow excellent levels of travel on the inner joints.

The higher strength and longer lasting TPE boots, OTK clamps and moly grease provide the best performance in extreme conditions and extend the life of your axle.

Features:

• Generous levels of swing angle.
• Excellent levels of travel on the inner joints.
• Best quality OTK clamps.
• Longer lasting, higher strength TPE boots.
• Moly grease for reliable performance.

NB: Please confirm suitability for your year, make, model prior to purchase.

Rough riding calls for stronger axles and that’s where All Balls Racing excels. Machined for exact OEM fit, the shaft is made of chromoly steel with a larger diameter than most axles. The axle has 6 ball bearings in each CV joint. Laminate coating resists corrosion and rust, and protects axle from dirt, water, rocks and grease. Waterproof neoprene boots act as a first line of defense, shielding vulnerable joints and preventing leaks. High performance molybdenum grease reduces heat and friction.

• In static torsion trials, these axles were up to 30% stronger than OEM and aftermarket competition.
• Lasts approximately 50 percent longer than many aftermarket competitors.
• Typically runs almost 130,000 cycles versus 80,000 cycles for many axles.

Features:

• 40% stronger than OEM.
• Larger 4340 chrome-moly steel axle bar.
• Precision ground components.
• Low profile clamps.
• Neoprene boots.
• Engineered in the USA.
• Manufactured in an ISO facility.
• Assembled with 3% molybdenum grease.

High-quality Steering Rack to suit Can-Am models.

Please refer to Fitment Guide for specific fit for your model.

Upgrade rubber bushings found in Utility ATV A-Arms to AB's redesigned HD Delrin bushings.
This kit is designed to replace worn out rubber bushings and provides greater suspension travel and performance.
Quality design and construction of every All Balls piece meets the toughest standards and conditions - from daily commuting to full-on racing, all older bearing and seal designs are upgraded to the best and latest specs and designs.

Upgrade rubber bushings found in Utility ATV A-Arms to AB's redesigned HD Delrin bushings.
This kit is designed to replace worn out rubber bushings and provides greater suspension travel and performance.
Quality design and construction of every All Balls piece meets the toughest standards and conditions - from daily commuting to full-on racing, all older bearing and seal designs are upgraded to the best and latest specs and designs.

Having the ability to turn corners is pretty important, so tie rod ends play a large role in any vehicle's safety. Whites Tie Rod End Kits are the perfect replacement for your old and worn out OE parts, or an excellent upgrade to your steering system.

To ensure a great fit we recommend using our fitments search, or referencing the fitments tab above.

Steel and aluminium construciton strengthened in critical areas for durability
Affordable OEM replacement
Mounts to your OEM Tie Rods

Kit Includes:
1 left-hand threaded tie rod end
1 jam nut
1 jam nut clip

Up to 40% stronger than OE axles, these complete axles feature enlarged CV joints, bearing cages, and chromoly axle shafts. All internal components are precision ground and utilize molybdenum grease.

Features:

• 40% stronger than OEM.
• Larger 4340 chrome-moly steel axle bar.
• Precision ground components.
• Low profile clamps.
• Neoprene boots.
• Engineered in the USA.
• Manufactured in an ISO facility.
• Assembled with 3% moly grease.
• Black oxide coating to resist rust and corrosion.