HARD PARTS

Rough riding calls for stronger axles and that’s where All Balls Racing excels. Machined for exact OEM fit, the shaft is made of chromoly steel with a larger diameter than most axles. The axle has 6 ball bearings in each CV joint. Laminate coating resists corrosion and rust and protects axles from dirt, water, rocks and grease. Waterproof neoprene boots act as a first line of defence, shielding vulnerable joints and preventing leaks. High-performance molybdenum grease reduces heat and friction.

In static torsion trials, these axles were up to 30% stronger than OEM and aftermarket competition.

Features:

• 40% stronger than OEM.
• Larger 4340 chrome-moly steel axle bar.
• Precision ground components.
• Low profile clamps.
• Lasts approximately 50 percent longer than many aftermarket competitors.
• Neoprene boots.
• Typically runs almost 130,000 cycles versus 80,000 cycles for many axles.
• Engineered in the USA.
• Manufactured in an ISO facility.Assembled with 3% molybdenum grease.

OEM spacers typically wear out within a year of hard riding. The wheel spacers should be checked and replaced as needed with every bearing service. Water and dirt act as a grinding compound between the seal face and the mating surface of the spacer. Once the grooves are deep enough, the sealing surface is lost, allowing water and dirt to pass through and contaminate the bearing.

Wheel Spacer Kits are designed to restore the proper sealing surface between the wheel seal and spacer, helping protect wheel bearings from premature wear and failure. Manufactured to precise tolerances for a direct replacement fit, All Balls spacers provide a smooth, durable surface for the seal to run against, reducing the risk of contamination and extending bearing life. Ideal for routine maintenance or during wheel bearing replacement, a quality wheel spacer kit ensures reliable wheel performance in harsh riding conditions.

P SERIES - Street Bikes

Premier's most successful general use material, our P series pads, are a tough Kevlar based organic material giving superb brake effect on all sportbikes and cruisers. This material is preselected by the catalogue when you order P prefix disc pads.

P SERIES - Off-Road

Part numbers relating to off-road machines are supplied in carbon graphite compound for medium durability, good brake effect and minimum heat generation.

Quality pair of fork oil seals from All Balls Racing.

Features:

• Dyno tested to last 3 to 4 times longer than OEM seals.
• Directional ribs on outside of seal allow seal to be installed easily.
• Dual-sealing lips guarantee oil stays in and dirt stays out.

P SERIES - Street Bikes

Premier's most successful general use material, our P series pads, are a tough Kevlar based organic material giving superb brake effect on all sportbikes and cruisers. This material is preselected by the catalogue when you order P prefix disc pads.

P SERIES - Off-Road

Part numbers relating to off-road machines are supplied in carbon graphite compound for medium durability, good brake effect and minimum heat generation.

High Quality Steering Rack from All Balls Racing.

Confirm suitability for year, make, model prior to purchase.

NOTE: This Vertex Oil Seal Set contains all components pictured.

Produced in the U.S.A. with the latest materials and technology in gasket production to Vertex specifications. Vertex gaskets ensure long-lasting performance and leak prevention for your rebuild needs. Vertex's replacement gaskets and seals are available as top-end kits, complete engine kits, or as an oil seal kit.

• These sets include all oil seals necessary to rebuild the engine and transmission including crankshaft, output shaft, water pump, clutch, and shifter seals.

Produced in the U.S.A. with the latest materials and technology in gasket production to Vertex specifications. Vertex gaskets ensure long-lasting performance and leak prevention for your rebuild needs.

• Ignition cover gasket
• Designed to fit O.E.M. cover

NOTE: This complete Vertex Gasket Set contains all parts as pictured.

Produced in the U.S.A. with the latest materials and technology in gasket production to Vertex specifications. Vertex gaskets ensure long-lasting performance and leak prevention for your rebuild needs. Vertex's replacement gaskets and seals are available as top-end kits, complete engine kits, or as an oil seal kit.

• One kit containing all of the gaskets, O-rings, and valve seals necessary to rebuild the entire engine and transmission.
• Includes transmission seals.

The  HFP-389-AP is a direct replacement intank fuel pump for EFI Aprilia motorcycle applications.  This is a direct fit pump, that requires no wiring modifications, and contains the correct OEM sized strainer which is not offered by other sellers and is essential to do the job correctly.  Cleaning and reusing your OEM strainer will lead to premature failure, as strainers become varnished internally, which makes the pump work harder.

HFP replacement fuel pumps, modules, assemblies, and kit components are designed to meet or exceed OEM specifications, and feature upgrades that improve on the OEM design. Upgraded polymers, brushes, and commutators ensure long life and durability in multiple fuel blends.

• OEM or better performance
• Polished corrosion-resistant case to help minimize seizing during non-operation
• Specifically designed for quiet operation
• Drop-in replacement
• Gradient density fuel strainer for superior contaminant filtration
• Patented check valve technology
• Compatible with modern ethanol-infused pump gasoline

NOTE: This complete Vertex Gasket Set contains all parts as pictured.

Produced in the U.S.A. with the latest materials and technology in gasket production to Vertex specifications. Vertex gaskets ensure long-lasting performance and leak prevention for your rebuild needs. Vertex's replacement gaskets and seals are available as top-end kits, complete engine kits, or as an oil seal kit.

• One kit containing all of the gaskets, O-rings, and valve seals necessary to rebuild the entire engine and transmission.
• Includes transmission seals.

Premier PR Series Brake Pad - SINTERED PADS FOR OFF-ROAD USE

Off-Road "Sintered" Premier "PR" pads have been upgraded to a HIGH DENSITY sintered metal compound suitable for all types of MX and ATV use.

Not for highway use.

Note: One set of brake pads services one brake disc, if you are servicing multiple discs you will need multiple sets of brake pads.

NOTE: This Vertex Top End Gasket Set contains all components pictured.

Produced in the U.S.A. with the latest materials and technology in gasket production to Vertex specifications. Vertex gaskets ensure long-lasting performance and leak prevention for your rebuild needs. Vertex's replacement gaskets and seals are available as top-end kits, complete engine kits, or as an oil seal kit.

• These sets include the head, base, and exhaust gaskets, valve seals, O-rings and other gaskets to complete a top-end rebuild.

PH SERIES – Street Sport “Sintered”

High-performance HH friction rated sintered metal pads made in the USA to an exclusive Premier formulation. PH brake pads offer maximum durability and unbeatable performance under heavy braking and high-speed use. Available for part numbers shown below - prefix with “PH to specify. PH series is no longer available for off-road applications following the formulation improvements of the PR range for Moto-X and ATV applications.

K&N's high-flow air filters are available as a replacement for your stock motorcycle air filter element. They are custom-engineered to fit your specific application and are designed to provide low restriction and increased performance while providing excellent engine protection for your motorcycle.

Features:

• Designed to provide increased horsepower and torque.
• Pleated media provides a large filtration area, offering long service intervals.
• Multiple layers of woven cotton gauze media offer excellent filtration.
• Application-specific base seal and sealing bead.
• Made in the USA for over 40 years.
• Washable and reusable, pre-oiled and ready to ride!

Specifications:

• Filter Material: Cotton Gauze
• Height: 3in (76mm)
• Inside Length: 4.25in (108mm)
• Inside Width: 3in (76mm)
• Washable: Yes
• Base Outside Length: 6.25in (159mm)
• Base Outside Width: 4.938in (125mm)
• Top Outside Length: 5.75in (146mm)
• Top Outside Width: 4.438in (113mm)
• Filter Re-Oiling Amount: 0.57oz (17ml)

NOTE: This Vertex Top End Gasket Set contains all components pictured.

Produced in the U.S.A. with the latest materials and technology in gasket production to Vertex specifications. Vertex gaskets ensure long-lasting performance and leak prevention for your rebuild needs. Vertex's replacement gaskets and seals are available as top-end kits, complete engine kits, or as an oil seal kit.

• These sets include the head, base, and exhaust gaskets, valve seals, O-rings and other gaskets to complete a top-end rebuild.

Use with any type of gasoline. Not for use with fuel injection systems.

Features:

• Resists swelling and hardening.
• Resistant to direct sunlight, hardening and/or cracking.
• Flexible in temperatures from -35F to +165F.
• Fuel line stretches easily over fittings or petcocks.
• Sold in 25-foot rolls.

• Kit contains direct OEM replacement shock bladder.
• The bladder is made from high-quality NBR rubber to ensure a leak-free pliable wall.

Re-install your original connector and grommet. Once your connector and grommet is re-installed, our part becomes a plug-and-play unit, direct fit, and very easy to install.

Features:

• Higher grade of electric components.
• Highest grade of copper winding, resistant to 200 degrees Celsius.
• All shipped products are tested.

Dimensions - Stator:

• Interior diameter: 28mm
• Exterior diameter: 57mm
• Thickness: 15mm
• Length of wires (stator to terminals): 600mm

Other Specifications:

• Number of wires: 4
• Number of plugs: 0
• Number of terminals: 4

Wire-to-Wire Resistance:

• Source 1: Red to White = 28 ohms ± 20%
• Source 2: Yellow to Yellow = 0.4 ohms ± 20%

Dimensions - Pickup Pulsar Coil:

• Height: 25mm
• Length: 22mm
• Width: 18mm
• Bracket (centre to centre): 35mm
• Wires length: 90mm

Other Specifications:

• Number of wires: 2
• Number of pins: 2

Wire-to-Wire Resistance:

• Pink/Red to White: 100 ohms ± 20%

GOLDfren began manufacturing sintered disc brake pads for a wide range of off-road and road motorcycles in 1991, nearly three decades on from their first motorcycle brake pads GOLDfren has become one of the largest aftermarket manufacturers in the motorcycle brake disc pad industry. Their development of next-generation products has kept them at the technological forefront of Sintered Friction Braking providing you with confidence in the performance, durability and reliability of your brakes.

S3 Series:

The S3 sintered compound is optimal in dry and wet conditions for road & off-road motorcycles. For the road application, S3 pads are suitable for both the front and rear brake while on off-road applications the S3 is only recommended for the front brake. The S3 series is designed for low abrasive interaction with the rotor and quieter braking due to the ceramic composite material. It has an HH friction rating and performs better at higher temperatures than the AD compound. Friction materials contain metal-ceramic with a bronze-graphite and non-metallic friction additives are spread evenly on the base fine bronze body to achieve optimal friction properties.

Features:

• Very high static friction coefficient
• Minimal difference between wet and dry braking performance
• Good abrasive resistance
• Low abrasive interaction with the brake rotor material
• Longer life compared to organic and Kevlar composite materials

Application:

• For riders who demand a bit more than average from their bikes
• Recommended on both front and rear brakes (road application)
• Can also be used on the front brakes of off-road bikes and ATVs
• Works well on both dry and wet conditions

Operating Parameters:

• Specific pressure: 3.0 Mpa
• Sliding speed: 45 m/s
• Constant maximum temp: 450°C
• Short time maximum temp: 800°C
• Counter-surfaces: steel disks

What is a sintered brake pad?

GOLDfren only manufacturers sintered brake pads that contain metal-ceramic and ceramic-carbon friction materials, these materials allow for less brake dust and a quieter braking experience. Sintered brake pads are made by fusing together metallic particles under high temperature and pressure which enhances friction properties and pad life, resulting in longer life and stronger braking. Sintered brake pads experience no brake fade when operating at high temperatures and in wet conditions. They also last up to 5 times longer than organic pads and provide additional braking strength. All materials used are environmentally friendly and do not contain any lead, asbestos, fibreglass or formaldehyde.

Reminder: one set of brake pads services one brake disc, if you are servicing multiple discs you will need multiple sets of brake pads.

All Balls Counter Shaft Washer Kit is made from premium products.

Kit includes 10x replacement counter shaft washers.

Wossner

For more than 35 years, Wössner successfully design and produce high-performance pistons and connecting rods.

In order to offer their customers the best of Wössner Power, their products are produced by using state-of-the-art technology and are subject to continuous quality control.

Performance, quality and longevity - this is what Wössner stands for with high-quality products.

Needle Bearings (Little End Bearings)

Please use our Fitments Tool to ensure the correct part is ordered.

Crafted from military-spec certified TI3Al titanium alloy, Vertex Titanium Valves are made to endure the harshest racing conditions. Forged from a single blank, grain flow is improved to enhance the mechanical characteristics of the valve without having to resort to welding. Special PVD, CVD, and CrN coatings are used to provide low-friction surfaces that reduce heat generation and resist carbon build-up; coatings allow alloys like titanium to become ultra-smooth while reaching hardness levels 5x that of high-speed steel.

• Military-spec certified TI3Al titanium alloy
• Forged from a single blank
• PVD, CVD, and CrN coatings
• Reduces heat generation
• Resists carbon build-up
• Significantly stronger than steel

Includes components necessary to complete a piston (top end) rebuild. Competitive pricing, made to meet and exceed OEM quality and designed as a direct OEM replacement.

Features:

• Designed for OEM replacement.
• Made from high-quality materials.
• Meet or exceed OEM specifications.
• Competitive pricing.

A quality caliper rebuild kit from All Balls. Contains everything needed to rebuild your caliper to like new condition.

Perfect for protecting your bars and grips or simply adding some additional style to your ride. The Oxford Bar Ends are CNC machined from lightweight, durable aluminium and complete with an anodised finish for a great look. Oxford's bar ends are compatible with all 7/8" (22mm) handlebars with an 18mm internal diameter.

Features:

• Essential anodised bar-ends.
• Colour matches with the motorcycle and adds style.
• Available in five high-quality anodised colours.
• Fits handlebars with 18mm internal diameters.
• Fits 7/8" (22mm) handlebars.
• 5mm hex key included.

Please Note:

1. All electrical components must be fitted by a qualified technician.
2. Before fitting electrical components ensure the root cause of the original failure has been addressed.
3. The absence of either of points 1 or 2 above, will void any warranty.