HARD PARTS

All Balls Counter Shaft Washer Kit is made from premium products.

Kit includes 10x replacement counter shaft washers.

All the bearings and seal required to refit a wheel in one convenient package.

Features:

• Premium high-speed bearings feature low drag.
• Double lip seals on both sides to provide superior exclusion of water and dirt
• Improved grease retention.

PH SERIES – Street Sport Sintered

High-performance HH friction rated sintered metal pads made in the USA to an exclusive Premier formulation. PH brake pads offer maximum durability and unbeatable performance under heavy braking and high-speed use. PH series is no longer available for off-road applications following the formulation improvements of the PR range for Moto-X and ATV applications.

Kit contains all of the components required to rebuild the shock bearing assembly properly.

Features:

• Needle bearing shafts are made with SCM415/42 bearing steel that has been hardened and precision ground.
• All metal bushings are case-hardened and plated to prevent wear and corrosion.
• POM composite washer bearings replace thru needle washers and increase service life and superb resistance to water and dirt.

Wossner

For more than 35 years, Wössner successfully design and produce high-performance pistons and connecting rods.

In order to offer their customers the best of Wössner Power, their products are produced by using state-of-the-art technology and are subject to continuous quality control.

Performance, quality and longevity - this is what Wössner stands for with high-quality products.

Con Rod Kits

The Wössner 2-stroke connecting rods are always supplied with lifting pins, needle bearings, connecting rod bearings and spacers.
The Wössner 4-stroke connecting rods include crank pins and connecting rod bearings.
Please use our Fitments Tool to ensure the correct part is ordered.

Each pack of Premier CSK Clutch Springs contains a complete set of heavy-duty springs. Up to 15% stronger than the original.

Customer should be advised that after installation of a CSK kit the clutch lever will feel slightly ‘heavier’ than standard

When it comes to quality, All Balls knows no compromises. All the products made under stringent quality control conditions. The latest manufacturing methods coupled with the use of the highest-grade materials ensure the closest tolerances are adhered to.

• Nut: 4
• Screw: 4

Crafted from military-spec certified TI3Al titanium alloy, Vertex Titanium Valves are made to endure the harshest racing conditions. Forged from a single blank, grain flow is improved to enhance the mechanical characteristics of the valve without having to resort to welding. Special PVD, CVD, and CrN coatings are used to provide low-friction surfaces that reduce heat generation and resist carbon build-up; coatings allow alloys like titanium to become ultra-smooth while reaching hardness levels 5x that of high-speed steel.

• Military-spec certified TI3Al titanium alloy
• Forged from a single blank
• PVD, CVD, and CrN coatings
• Reduces heat generation
• Resists carbon build-up
• Significantly stronger than steel

• Direct OEM replacement fuel line clamp kit
• This ultimate fuel line clamp kit is an absolute necessity for any shop, technician, or DIY mechanic
• Kit contains 4 of each Fuel Star fuel line OEM replica clamps, available in sizes from 7-17mm I.D.
• Each clamp is an exact replica of the major OEM's fuel line clamps and is manufactured to meet or exceed OEM performance, aesthetics, and fit
• 4-packs also available to refill the kit

Brand new aftermarket Voltage Regulator Rectifier

• Direct replacement to your original unit
• Plug-and-play, direct fit, easy installation
• No assembly required
• Higher grade of electric components
• The quality exceeds the OEM equipment
• All products shipped are tested

We have even included the opposite connector (main harness side) as we know these are often melted corroded defective and a major cause for repetitive electrical issues.

Specifications:

Dimensions: p>

• Width: 73 mm
• Length: 46 mm
• Height: 30 mm

Other specifications:

• Number of plugs: 1
• Number of pins: 5
• Minimum Charging Voltage: 14.5 V +- 0.5 V
• Maximum Charging Current: 50 A / 500 W
• Open Circuit Voltage: < 15 V
• Operation Temperature: -20°C to 85°C

P SERIES - Street Bikes

Premier's most successful general use material, our P series pads, are a tough Kevlar based organic material giving superb brake effect on all sportbikes and cruisers. This material is preselected by the catalogue when you order P prefix disc pads.

P SERIES - Off-Road

Part numbers relating to off-road machines are supplied in carbon graphite compound for medium durability, good brake effect and minimum heat generation.

K&N's high-flow air filters are available as a replacement for your stock motorcycle air filter element. They are custom-engineered to fit your specific application and are designed to provide low restriction and increased performance, while providing excellent engine protection for your motorcycle.

Features:

• Designed to provide increased horsepower and torque.
• Pleated media provides a large filtration area, offering long service intervals.
• Multiple layers of woven cotton gauze media offer excellent filtration.
• Application-specific base seal and sealing bead.
• Made in the USA for over 40 years.
• Washable and reusable, pre-oiled and ready to ride!

Specifications:

• Washa ble: Yes
• Filter Material: Cotton Gauze
• Height: 102mm
• Base Outside Diameter: 127mm
• Top Outside Diameter: 89mm
• Flange Inside Diameter: 89mm
• Flange Length: 16mm

Fitting a set of after market indicators is now a straight forward task. The Oxford Indicator Spacers neatly fills the holes in the fairing left by the standard Indicators.

Any set of Oxford Indicator Spacers can now be fitted without leaving unsightly gaps or holes at the mounting point.

Features:

• Fits both front and rear.
• A set of 4 will secure 2 indicators.
• Requires no modification to fairings.
• Made of high quality and durable plastic.
• Comes with an 8mm hole in each spacer.

RMSTATOR is specialized in designing and manufacturing innovative electrical and electronic components for Powersports vehicles like motorcycles, ATV, SxS, UTV, snowmobiles, and PWC. Through unrelenting quality control, we ensure that each component meets or exceeds the OEM specs. With over 25 product families, rest assured that you will find the part you need.

• Direct replacement to your original unit
• Plug-and-play, direct fit, easy installation
• Highest grade of lamination materials
• Highest grade of copper winding, resistant to 200 degrees Celsius
• Connector included

Battery condition is extremely important. No stator can work correctly with a bad or weak battery. Always fully charge your battery before performing any charging system tests or replacing parts. If there is any doubt, have the battery load tested or replaced.

Please Note:

1. All electrical components must be fitted by a qualified technician.
2. Before fitting electrical components ensure the root cause of the original failure has been addressed.
3. The absence of either of points 1 or 2 above, will void any warranty.

Air Cut Off Valve Rebuild Kits

Poor running conditions or popping on deceleration are signs that you may need to rebuild the air cut off valve.

All of the necessary parts to rebuild the air cut off valve circuit are included. Kits for vehicles with multiple carburetors include all components for all carburetors.

Please Note:

1. All electrical components must be fitted by a qualified technician.
2. Before fitting electrical components ensure the root cause of the original failure has been addressed.
3. The absence of either of points 1 or 2 above, will void any warranty.

Quality carburettor rebuild kit from All Balls.

• Kits include all of the necessary components to repair a carburettor. ATV models with two carburettors include components to repair two carburettors.
• Kit includes necessary all O-rings, gaskets, jets, needle, mixture screw, float bowl screws, float valve needles and seat. (Needle jet and other pressed-in jets are not included in the kit.)
• OEM jet sizes are included in the kit. NBR rubber material is used on all O-rings and rubber gaskets NBR has excellent resistance to the ethanol used in today’s fuels.
• Applications that use paper float bowl gaskets are upgraded to High-Performance Interface Gasket material.
• Components included in the kits are based on US models and discretion must be used when attempting to install the kit on a non-US model.
• Off-road use only.

No-Toil Air Filters are built with the highest quality materials to ensure that they are long-lasting. Made with the finest dual-stage, flame-laminated foam to effectively stop dirt, and a high strength glue.

Features:

• No Toil manufactures the world's best 2-stage foam air filters.
• Using only the best flame-laminated dual-layer foam bonded with the highest quality glue, they hand-make each foam filter to stand up to the roughest and toughest of any style of riding or terrain.
• These filters, used with No-Toil foam filter oil, provide the best air filtration system in the world!

Please Note:

1. All electrical components must be fitted by a qualified technician.
2. Before fitting electrical components ensure the root cause of the original failure has been addressed.
3. The absence of either of points 1 or 2 above, will void any warranty.

A quality CV Boot Kit from All Balls. Comes complete with CV Boot, clamps and grease.

REGULATOR YAM YZF600, YZFR1/R6, VMAX, FZR - H/DUTY

Quality replacement Regulator/Rectifiers.

Please Note:

1. All electrical components must be fitted by a qualified technician.
2. Before fitting electrical components ensure the root cause of the original failure has been addressed.
3. The absence of either of points 1 or 2 above, will void any warranty.

HFP replacement fuel pumps, modules, assemblies, and kit components are designed to meet or exceed OEM specifications, and feature upgrades that improve on the OEM design. Upgraded polymers, brushes, and commutators ensure long life and durability in multiple fuel blends.

• OEM or better performance
• Polished corrosion-resistant case to help minimize seizing during non-operation
• Specifically designed for quiet operation
• Drop-in replacement
• Gradient density fuel strainer for superior contaminant filtration

Master Cylinder Repair Kits

• Kits contain all of the components to re-seal leaking master cylinders.
• Kits contain copper washers, replacement screws where applicable, cup seals, o-rings and replacement piston.

Replaces leaky seals and bushings behind countershaft sprockets. Competitively priced against OEM parts. Quick solution to repairing a leaking counter shaft seal in one complete kit.

Includes:

• Hot Rods countershaft seal
• Countershaft bushing
• O-rings
• Sprocket nut washer (where applicable)

Note:

Does not include water pump bearings or transmission bearings.

Versatile and high-performance tyre for Junior Motocross and Enduro, perfect for usage on a variety of terrains when training, racing or simply having fun.

Features:

• Off-road dedicated compound, increasing traction on medium to hard surfaces with greatly reduced knobs consumption.
• Synthetic fibers x-ply structure improving support when leaning, climbing up and down obstacles, and shifting weights between wheels.
• Knobs layout and shape enhancing off-road traction when leaning, braking and accelerating.
• Knobs symmetrical geometry allows reversing the tyre when a side is worn, increasing its durability.

NOTE: This complete Vertex Gasket Set contains all parts as pictured.

Produced in the U.S.A. with the latest materials and technology in gasket production to Vertex specifications. Vertex gaskets ensure long-lasting performance and leak prevention for your rebuild needs. Vertex's replacement gaskets and seals are available as top-end kits, complete engine kits, or as an oil seal kit.

• One kit containing all of the gaskets, O-rings, and valve seals necessary to rebuild the entire engine and transmission.
• Includes transmission seals.

All necessary parts to replace the fuel pump module.

Features:

• Includes complete module, retaining nut and gasket.
• Restores lost performance or non-functioning fuel pump with this economical solution.
• Pump draws less current than OEM counterpart while maintaining the same flow rate at working pressure, which reduces working temperatures and increases the life of the unit.

Note: Specific parts vary from kit to kit depending on the needs of your vehicle model.

Crafted from military-spec certified TI3Al titanium alloy, Hot Cams Titanium Valves are made to endure the harshest racing conditions. Forged from a single blank, grain flow is improved to enhance the mechanical characteristics of the valve without having to resort to welding. Special PVD, CVD, and CrN coatings are used to provide low-friction surfaces that reduce heat generation and resist carbon build-up; coatings allow alloys like titanium to become ultra-smooth while reaching hardness levels 5x that of high-speed steel.

• Military-spec certified TI3Al titanium alloy
• Forged from a single blank
• PVD, CVD, and CrN coatings
• Reduces heat generation
• Resists carbon build-up
• Significantly stronger than steel

Specifications:

• Material: Titanium
• Valve Head Outer Diameter: 36mm
• Valve Length: 85mm
• Valve Stem Outer Diameter: 5.480mm