HARD PARTS

Whites Oil Filters are designed to trap harmful contaminants while still allowing a high oil flow rate.

Features:

• Designed for great filtration.
• Oil filter design provides for a high rate of oil flow.
• Filters available for almost all makes and models.

Kit includes case-hardened bushing, replacement outer seal along with any O-rings, snap rings or lock washers required to complete the repair.

Features:

• Hardened bushings reduce wear and seal damage.
• Upgraded seal material reduces bushing wear and increases life.
• Brushing coating reduces corrosion.

Note: Verify fitment before purchasing.

Maximise your motorcycles engine cleaning system with Whites Magnetic Oil Drain Plugs, available for almost every make and model of motorcycle these anodised aluminium plugs include a magnetic core that is designed to catch any metal shavings in your motorcycles oil. Extra protection can't hurt, a simple inexpensive magnetic sump plug could prevent a costly engine rebuild or prevent permanent damage to your engine.

• Thread Size: M12 x 12mm
• Thread Pitch: 1.25mm
• Colour: Gold
• Pre-drilled hole in the head for use with safety wire
• Aluminium crush washer prevents leaks
• Anodised aluminium for a great look and durability

NOTE: All Aluminium Magnetic Drain Plugs should be tightened to the OEM specifications found in your owners/service manual.

• Dynamically balanced and phased as complete 2-piece (where applicable) assemblies by the manufacturer
• The complete driveline is balanced to reduce noise and vibration while extending its life
• Carrier bearing included (where applicable) – including the carrier bearing reduces cost, eases assembly, and provides a complete ready to install driveline
• Designed with the same dimensions as an OEM drive shaft for guaranteed fitment
• Greaseable u-joints allow maintenance of the driveshaft

The Whites OEM replacement cast levers provide an economical alternative to original levers. The perfect spare to have ready in your workshop in case of race day disaster. Available in black and OEM silver finish (model dependent).

Features:

• Direct OEM replacement cast levers.
• Designed to exceed OEM specifications.
• Built to resist breakage.
• Designed to fit OEM perch.
• Made from die-cast aluminum for maximum durability and affordability.

Ideal replacement for dirt bikes.

Features:

• Anti-swell alloy impregnated heavy-duty cork-based facings.
• Smooth clutch take up compared to paper clutches, which can ‘snatch’.
• Steel separator plates increase flywheel effect of the engine and improve performance.

Produced in the U.S.A. with the latest materials and technology in gasket production to Vertex specifications. Vertex gaskets ensure long-lasting performance and leak prevention for your rebuild needs.

• Inner clutch cover gasket
• Designed to fit O.E.M. cover

A quality pair of fork oil and dust seals from All Balls Racing.

Features:

• Dyno tested to last 3 to 4 times longer than OEM seals.
• Directional ribs outside of the seal allow easy installation.
• Dual-sealing lips guarantee oil stays in and dirt stays out.

High-quality crankshaft oil seals that are sold in a set.

Features:

• Replace OE originals exactly for proper fit and secure seal.
• Double lip seals with PTFE contact area tolerate dry start conditions with less crankshaft pin wear.

Notify: Verify part fitment before purchasing.

NOTE: This complete Vertex Gasket Set contains all parts as pictured.

Produced in the U.S.A. with the latest materials and technology in gasket production to Vertex specifications. Vertex gaskets ensure long-lasting performance and leak prevention for your rebuild needs. Vertex's replacement gaskets and seals are available as top-end kits, complete engine kits, or as an oil seal kit.

• One kit containing all of the gaskets, O-rings, and valve seals necessary to rebuild the entire engine and transmission.
• Includes transmission seals.

RPHX SERIES – Sintered Metal Pads for Road Race Use

This sintered range provides the very latest in sintered friction pad technology to deliver more stopping power, totally silent braking and longer life.

A quality pair of fork oil and dust seals from All Balls Racing.

Features:

• Dyno tested to last 3 to 4 times longer than OEM seals.
• Directional ribs outside of the seal allow easy installation.
• Dual-sealing lips guarantee oil stays in and dirt stays out.

NOTE: This complete Vertex Gasket Set contains all parts as pictured.

Produced in the U.S.A. with the latest materials and technology in gasket production to Vertex specifications. Vertex gaskets ensure long-lasting performance and leak prevention for your rebuild needs. Vertex's replacement gaskets and seals are available as top-end kits, complete engine kits, or as an oil seal kit.

• One kit containing all of the gaskets, O-rings, and valve seals necessary to rebuild the entire engine and transmission.
• Includes transmission seals.

K&N's Universal Air Filters are designed and manufactured for a wide variety of applications, including racing vehicles, radio-controlled cars, generators, snowmobiles, tractors, and other applications. Regardless of the angle or offset diameter of the air intake, there is probably a K&N Universal air filter for your equipment. All filters are constructed with ultra-strong moulded pliable rubber flanges which absorb vibration and allow for secure attachment and can also be stretched for up to 1/16 of an inch (1.5mm) to fit in-between sizes. K&N universal air filters are washable and reusable.

Features:

• Designed to increase horsepower and acceleration.
• Hundreds of sizes and shapes for most applications.
• High airflow with excellent filtration.
• Clamp-on washable and reusable air filter.
• Malleable flanges.

Specifications:

• Fi lter Material: Cotton Gauze
• Outside Diameter: 95mm
• Height: 152mm
• Flange Inside Diameter: 62mm
• Flange Length: 51mm
• Flange Type: Angled
• Flange Angle: 20 degrees

All Balls Master Cylinder Rebuild Kit

- Kits contain all of the components to re-seal leaking master cylinders.
- Kits contain copper washers, replacement screws where applicable, cup seals, o-rings and replacement piston.

P SERIES - Street Bikes

Premier's most successful general use material, our P series pads, are a tough Kevlar based organic material giving superb brake effect on all sportbikes and cruisers. This material is preselected by the catalogue when you order P prefix disc pads.

P SERIES - Off-Road

Part numbers relating to off-road machines are supplied in carbon graphite compound for medium durability, good brake effect and minimum heat generation.

KoubaLink specialises in motorcycle lowering and performance linkages for off-road and dual-sport rear suspension systems. Compromise is not an option at KoubaLink. Listening to riders from all over the world explain where and how they use their off-road and dual-sport bikes. With their input, Koubalink manufacture products that add to your motorcycling experience and make it a little more enjoyable.

• Provides better front-end stability by lowering rear suspension geometry
• Machined from billet aluminium
• Stronger than OEM
• Pre-installed OE style bearings included
• Replace linkage like its OEM
• Includes all required bearings and seals for assembly (Excluding Dog Bone styled linkages that do not include bearings and seals from factory)

Rough riding calls for stronger axles and that’s where All Balls Racing excels. Machined for exact OEM fit, the shaft is made of chromoly steel with a larger diameter than most axles. The axle has 6 ball bearings in each CV joint. Laminate coating resists corrosion and rust and protects axles from dirt, water, rocks and grease. Waterproof neoprene boots act as a first line of defence, shielding vulnerable joints and preventing leaks. High-performance molybdenum grease reduces heat and friction.

In static torsion trials, these axles were up to 30% stronger than OEM and aftermarket competition.

Features:

• 40% stronger than OEM.
• Larger 4340 chrome-moly steel axle bar.
• Precision ground components.
• Low profile clamps.
• Lasts approximately 50 percent longer than many aftermarket competitors.
• Neoprene boots.
• Typically runs almost 130,000 cycles versus 80,000 cycles for many axles.
• Engineered in the USA.
• Manufactured in an ISO facility.Assembled with 3% molybdenum grease.

KoubaLink specialises in motorcycle lowering and performance linkages for off-road and dual-sport rear suspension systems. Compromise is not an option at KoubaLink. Listening to riders from all over the world explain where and how they use their off-road and dual-sport bikes. With their input, Koubalink manufacture products that add to your motorcycling experience and make it a little more enjoyable.

Features:

• Provides better front-end stability by lowering rear suspension geometry.
• Machined from billet aluminium.
• Stronger than OEM.
• Pre-installed OE style bearings included.
• Replace linkage like its OEM.
• Includes all required bearings and seals for assembly (Excluding Dog Bone styled linkages that do not include bearings and seals from factory).

NOTE: This complete Vertex Gasket Set contains all parts as pictured.

Produced in the U.S.A. with the latest materials and technology in gasket production to Vertex specifications. Vertex gaskets ensure long-lasting performance and leak prevention for your rebuild needs. Vertex's replacement gaskets and seals are available as top-end kits, complete engine kits, or as an oil seal kit.

• One kit containing all of the gaskets, O-rings, and valve seals necessary to rebuild the entire engine and transmission.
• Includes transmission seals.

Premium OEM Quality. Replaces complete steering rack. Fraction of the price of OEM.

Please Note:

1. All electrical components must be fitted by a qualified technician.
2. Before fitting electrical components ensure the root cause of the original failure has been addressed.
3. The absence of either of points 1 or 2 above, will void any warranty.

NOTE: This Vertex Top End Gasket Set contains all components pictured.

Produced in the U.S.A. with the latest materials and technology in gasket production to Vertex specifications. Vertex gaskets ensure long-lasting performance and leak prevention for your rebuild needs. Vertex's replacement gaskets and seals are available as top-end kits, complete engine kits, or as an oil seal kit.

• These sets include the head, base, and exhaust gaskets, valve seals, O-rings and other gaskets to complete a top-end rebuild.

A quality ATV IRS knuckle kit from All Balls Racing containing everything required to rebuild an ATV IRS knuckle. Confirm suitability for your year, make, model prior to purchase.

Quality design and construction of every All Balls piece meets the toughest standards and conditions — from daily commuting to full-on racing, all older bearing and seal designs are upgraded to the best and latest specs and designs.

Upgrades rubber bushings found in Utility ATV A-Arms to ABs redesigned HD Delrin bushings. Designed to replace worn-out rubber bushings and provide greater suspension travel and performance.

Kit includes water pump cover gasket or o-ring, water pump shaft bearing(s) and seal(s) to repair a leaking water pump seal and/or a failed bearing.

Features:

• Precision micro bearings provide OE quality and durability.
• High pressure/temperature mechanical and rubber seals.

Includes all gaskets and o-rings necessary to complete a piston (top end) rebuild. Competitive pricing, made to meet and exceed OEM quality and designed as a direct OEM replacement the Whites Complete Gasket Set if your one stop shop for engine rebuilds.

Designed for OEM replacement
Made from high quality materials
Meet or exceed OEM specifications
Competitive pricing

Quality carburettor rebuild kit from All Balls.

• Kits include all of the necessary components to repair a carburettor. ATV models with two carburettors include components to repair two carburettors.
• Kit includes necessary all O-rings, gaskets, jets, needle, mixture screw, float bowl screws, float valve needles and seat. (Needle jet and other pressed-in jets are not included in the kit.)
• OEM jet sizes are included in the kit. NBR rubber material is used on all O-rings and rubber gaskets NBR has excellent resistance to the ethanol used in today’s fuels.
• Applications that use paper float bowl gaskets are upgraded to High-Performance Interface Gasket material.
• Components included in the kits are based on US models and discretion must be used when attempting to install the kit on a non-US model.
• Off-road use only.

WHITES REPLACEMENT BRAKE SHOES

• OE quality replacement brake shoes
• Edge trimmed and radius ground to ensure these brake shoes fit exactly into the drum
• Linings are bonded and chamfered on the ends
• Made from high-pressure die-cast aluminium

Quality carburettor rebuild kit from All Balls.

• Kits include all of the necessary components to repair a carburettor. ATV models with two carburettors include components to repair two carburettors.
• Kit includes necessary all O-rings, gaskets, jets, needle, mixture screw, float bowl screws, float valve needles and seat. (Needle jet and other pressed-in jets are not included in the kit.)
• OEM jet sizes are included in the kit. NBR rubber material is used on all O-rings and rubber gaskets NBR has excellent resistance to the ethanol used in today’s fuels.
• Applications that use paper float bowl gaskets are upgraded to High-Performance Interface Gasket material.
• Components included in the kits are based on US models and discretion must be used when attempting to install the kit on a non-US model.
• Off-road use only.