HARD PARTS

The Oxford Products Racing Lever guards are designed to help avoid the accidental engagement of the front brake lever during close wheel-to-wheel racing. These offer a universal fitment as they fit all 22mm handlebars using 12-18-inch expansion bolts. They are made from highly durable reinforced Delrin acetal 100ST composite.

Features:

• Designed to help avoid the accidental engagement of the front brake lever during close wheel-to-wheel racing.
• Very easy to install.
• Fit all 22mm handlebars using 12-18-inch expansion bolts.
• Highly durable reinforced Delrin acetal 100ST composite.
• Left only.

All necessary parts to replace the fuel pump module.

Features:

• Includes complete module, retaining nut and gasket.
• Restores lost performance or non-functioning fuel pump with this economical solution.
• Pump draws less current than OEM counterpart while maintaining the same flow rate at working pressure, which reduces working temperatures and increases the life of the unit.

Note: Specific parts vary from kit to kit depending on the needs of your vehicle model.

NOTE: This Vertex Top End Gasket Set contains all components pictured.

Produced in the U.S.A. with the latest materials and technology in gasket production to Vertex specifications. Vertex gaskets ensure long-lasting performance and leak prevention for your rebuild needs. Vertex's replacement gaskets and seals are available as top-end kits, complete engine kits, or as an oil seal kit.

• These sets include the head, base, and exhaust gaskets, valve seals, O-rings and other gaskets to complete a top-end rebuild.

The Whites OEM replacement cast levers provide an economical alternative to original levers. The perfect spare to have ready in your workshop in case of race day disaster. Available in black and OEM silver finish (model dependent).

Features:

• Direct OEM replacement cast levers.
• Designed to exceed OEM specifications.
• Built to resist breakage.
• Designed to fit OEM perch.
• Made from die-cast aluminum for maximum durability and affordability.

• Direct replacement to your original unit.
• Plug-and-play, direct fit, easy installation.
• No assembly required
• The Quality exceeds the OEM equipment
• Improved heat sink and charging capabilities
• Higher grade of electric components.
• All products shipped are tested

We have even included the opposite connector (main harness side) as we know these are often melted/corroded/defective and a major cause for repetitive electrical issues.

*All item pictures are accurate, if in doubt do not hesitate and compare our item to your original part.

Specifications:

• Dimensions:

  • Width: 80mm
  • Length: 103mm
  • Height: 32mm
  • Fixation holes centre to centre: 75mm
  • Wires length: 120mm

• Other Specifications:

  • Number of plugs: 1
  • Number of pins: 5
  • Minimum Charging Voltage: 14.5V ± 0.5V
  • Maximum Charging Current: 25A-35A/300W-500W
  • Open Circuit Voltage: <15V
  • Operating Temperature: -20°C to 85°C

Kit contains the necessary seals to repair oil leaks and rebuild the transaxle. Direct OEM replacement at a fraction of the cost.

Note: Verify fitment before purchasing.

The K&N Airforce Pre-Cleaner is a specially designed foam filter wrap made to extend the service interval of your K&N air filter when used in very dusty conditions. The Airforce Pre-Cleaner is designed to be cleaned with K&N Cleaner or soap & water. Airforce pre-cleaners are oiled with K&N air filter oil after they are cleaned. They are made from large, open-cell foam.

Features:

• Extends service interval of your filter in very dusty conditions.
• Large open cell foam construction stops 90% of dirt with very low air restriction.
• Cleanable with K&N Filter Cleaner or soap and water.
• This product wraps your air filter with an additional pre-filter.

Specifications:

• Wrap Material: Foam
• Inside Diameter: 95mm
• Height: 152mm

All new assembly sold complete with Hot Rods connecting rod.

• The Hot Rods complete crankshaft includes their famed connecting rod; durability at a level OEM rods can only dream of.
• Factory assembled and trued to O.E.M. specifications, Hot Rods cranks will meet or surpass the OEM in performance. Hot Rods makes installing the complete crankshaft simple and easy.
• Crankshaft is completely rebuildable with genuine Hot Rods connecting rods.

Note: Crank bearings and seals sold separately.

All the bearings and seal required to refit a wheel in one convenient package.

Features:

• Premium high-speed bearings feature low drag.
• Double lip seals on both sides to provide superior exclusion of water and dirt
• Improved grease retention.

PR SERIES – Off-Road Sintered

Premier PR pads have been upgraded to a new HIGH DENSITY sintered metal compound suitable for all types of moto-x and ATV use.

GOLDfren began manufacturing sintered disc brake pads for a wide range of off-road and road motorcycles in 1991, nearly three decades on from their first motorcycle brake pads GOLDfren has become one of the largest aftermarket manufacturers in the motorcycle brake disc pad industry. Their development of next-generation products has kept them at the technological forefront of Sintered Friction Braking providing you with confidence in the performance, durability and reliability of your brakes.

K5 Series:

The K5 sintered compound is optimal for off-road motorcycles and ATVs. It is recommended for riders who demand great off-road stopping power and brake pad durability when riding on tough off-road terrains. The K5 series is designed for low abrasive interaction with the rotor, long life and self-cleaning capabilities necessary in off-road riding conditions. Friction materials contain metal-ceramic with a sophisticated bronze-graphite and full-metal mixture formulation with fine friction particles to achieve optimal friction properties.

Features:

• High static friction coefficient
• Good abrasive resistance
• Self-cleaning capability
• Low abrasive interaction with the brake rotor material
• Up to 3 times longer operational life compared to organic and Kevlar composite materials

Application:

• Developed specifically for off-road motorcycles & ATVs
• Can be used on both front and rear brakes
• Could be used on the rear brake of road racing motorcycles

Operating Parameters:

• Specific pressure: 2.0 Mpa
• Sliding velocity: 20 m/s
• Constant maximum temp: 500°C
• Short time maximum temp: 750°C
• Counter-surfaces: steel disks

What is a sintered brake pad?

GOLDfren only manufacturers sintered brake pads that contain metal-ceramic and ceramic-carbon friction materials, these materials allow for less brake dust and a quieter braking experience. Sintered brake pads are made by fusing together metallic particles under high temperature and pressure which enhances friction properties and pad life, resulting in longer life and stronger braking. Sintered brake pads experience no brake fade when operating at high temperatures and in wet conditions. They also last up to 5 times longer than organic pads and provide additional braking strength. All materials used are environmentally friendly and do not contain any lead, asbestos, fibreglass or formaldehyde.

Reminder: one set of brake pads services one brake disc, if you are servicing multiple discs you will need multiple sets of brake pads.

A quality caliper rebuild kit from All Balls. Contains everything needed to rebuild your caliper to like new condition.

PH SERIES – Street Sport Sintered

High-performance HH friction rated sintered metal pads made in the USA to an exclusive Premier formulation. PH brake pads offer maximum durability and unbeatable performance under heavy braking and high-speed use. PH series is no longer available for off-road applications following the formulation improvements of the PR range for Moto-X and ATV applications.

Master Cylinder Repair Kits

• Kits contain all of the components to re-seal leaking master cylinders.
• Kits contain copper washers, replacement screws where applicable, cup seals, o-rings and replacement piston.

A quality pair of fork oil and dust seals from All Balls Racing.

Features:

• Dyno tested to last 3 to 4 times longer than OEM seals.
• Directional ribs outside of the seal allow easy installation.
• Dual-sealing lips guarantee oil stays in and dirt stays out.

If you have a broken tie rod or just want some extra protection against breakage, take the opportunity to beef up the tie rods on your ATV with the All Balls Tie Rod Upgrade Kit.

The tie rods and ends included with this kit have improved resistance against bending and breaking, thanks to thicker 12mm ends compared to the 10mm stock ends. The kit gets even better when you consider the entire kit from All Balls retails for less than the cost of replacing 4 OEM tie rod ends.

This kit comes with 2 tie rods, 4 tie rod ends, and all the parts you’ll need to replace your old tie rods with the upgraded parts in the Tie Rod Upgrade Kit from All Balls.

Features:

• Upgrade 10mm tie rod ends to heavy-duty 12mm ends.
• Kit includes parts for conversion, 2 tie rods, and 4 rod ends.
• Retails for less than the cost of replacing 4 OEM 10mm tie rod ends.

Stop burning your regulator rectifier! It is time to update or replace your voltage regulator with the advanced MOSFET type.

This product is an advanced design that lowers operating temperatures for extended longevity and better performance than the OEM part.

It runs cooler than all OEM diode-style regulators. In addition, this rectifier has overheat protection, rather than burn up it will simply turn off for a while and cool off.

• Direct replacement to your original unit
• Plug-and-play, direct fit, easy installation
• The quality exceeds the OEM equipment
• Higher grade of electric components
• All shipped products are tested

Specifications:

Dimensions:

• Width: 62 mm
• Length: 65 mm
• Height: 25 mm
• Fixation holes centre to centre: 67 mm
• Wires Length: 158 mm and 198 mm

Other specifications:

• Number of plugs: 4
• Number of pins: 5
• Number of wires: 5
• Minimum Charging Voltage: 14.5 V +/- 0.5 V
• Maximum Charging Current: 50 A / 500 W
• Open Circuit Voltage: 15 V
• Operating Temperature: -20° to 85°

Wrench Rabbit Rebuild Kits have been rebranded to Vertex Rebuild Kits; all components remain unchanged however you may receive a kit that is boxed differently to the one pictured.

Vertex Complete Engine Rebuild Kits are a simple and cost-effective way to complete a top-to-bottom professional rebuild for your 2 or 4-stroke motorcycle or ATV/UTV. The one easy to order kit will not only save you time by offering a one-stop-shop in a box, but they also save you money when compared to purchasing all items individually.

Vertex kits include quality components from Vertex, Hot Rods & Hot Cams.*

All parts are manufactured in the USA from the highest quality material.

Features:

• Crafted to deliver unbeatable levels of quality
• High-grade materials for exceptional performance
• Superior in durability and reliability
• Kits available for many 2 & 4-stroke motorcycles, ATVs & UTVs
• Cost-effective solution
• Saves time sourcing individual components
• Vertex pistons & gaskets*
• Hot Rods crank & bearing kits*
• Hot Cams cam chain*

Includes:

• Crankshaft
• Piston Kit
• Complete Engine Gasket Kit
• Oil Seal Kit
• Main Bearing and Seal Kit
• Water Pump Rebuild Kit
• Transmission Bearing Kit
• Countershaft Bushing/Seal Kit
• Cam Chain

*Specific parts vary by kit (see included parts above).

Quality design and construction of every All Balls piece meets the toughest standards and conditions - from daily commuting to full-on racing, all older bearing and seal designs are upgraded to the best and latest specs and designs.

Available individually in left-hand and right-hand thread or sold in pairs one L/H and one R/H thread.

Brand new generator stator

• Direct replacement to your original unit
• Plug-and-play, direct fit, easy installation.
• Highest grade lamination materials
• Highest grade copper windings, resistant to 200 degrees Celsius.
• Pick up pulsar coil included
• Connector included
• Rubber grommet included
• All products shipped are tested

Dimensions:

• Interior diameter: 42mm
• Exterior diameter: 106mm
• Thickness: 20mm
• Length of wires stator to grommet: 100mm
• Length of wires grommet to plug: 250mm
• Length of pickup coil's wire to grommet: 80mm
  
  

Other specifications:

• Number of wires: 5
• Number of plugs: 1
• Number of pins: 5

Wire to wire resistance:

• Alternator: Yellow between each Yellow = 0.4ohms +/-20%
• Pickup: Blue to Green = 115ohms +/-20%

Battery condition is extremely important. No stator can work correctly with a bad or weak battery. Always fully charge your battery before performing any charging system tests or replacing parts. If there is any doubt, have the battery load tested or replaced.

Please Note:

1. All electrical components must be fitted by a qualified technician.
2. Before fitting electrical components ensure the root cause of the original failure has been addressed.
3. The absence of either of points 1 or 2 above, will void any warranty.

GOLDfren began manufacturing sintered disc brake pads for a wide range of off-road and road motorcycles in 1991, nearly three decades on from their first motorcycle brake pads GOLDfren has become one of the largest aftermarket manufacturers in the motorcycle brake disc pad industry. Their development of next-generation products has kept them at the technological forefront of Sintered Friction Braking providing you with confidence in the performance, durability and reliability of your brakes.

S3 Series:

The S3 sintered compound is optimal in dry and wet conditions for road & off-road motorcycles. For the road application, S3 pads are suitable for both the front and rear brake while on off-road applications the S3 is only recommended for the front brake. The S3 series is designed for low abrasive interaction with the rotor and quieter braking due to the ceramic composite material. It has an HH friction rating and performs better at higher temperatures than the AD compound. Friction materials contain metal-ceramic with a bronze-graphite and non-metallic friction additives are spread evenly on the base fine bronze body to achieve optimal friction properties.

Features:

• Very high static friction coefficient
• Minimal difference between wet and dry braking performance
• Good abrasive resistance
• Low abrasive interaction with the brake rotor material
• Longer life compared to organic and Kevlar composite materials

Application:

• For riders who demand a bit more than average from their bikes
• Recommended on both front and rear brakes (road application)
• Can also be used on the front brakes of off-road bikes and ATVs
• Works well on both dry and wet conditions

Operating Parameters:

• Specific pressure: 3.0 Mpa
• Sliding speed: 45 m/s
• Constant maximum temp: 450°C
• Short time maximum temp: 800°C
• Counter-surfaces: steel disks

What is a sintered brake pad?

GOLDfren only manufacturers sintered brake pads that contain metal-ceramic and ceramic-carbon friction materials, these materials allow for less brake dust and a quieter braking experience. Sintered brake pads are made by fusing together metallic particles under high temperature and pressure which enhances friction properties and pad life, resulting in longer life and stronger braking. Sintered brake pads experience no brake fade when operating at high temperatures and in wet conditions. They also last up to 5 times longer than organic pads and provide additional braking strength. All materials used are environmentally friendly and do not contain any lead, asbestos, fibreglass or formaldehyde.

Reminder: one set of brake pads services one brake disc, if you are servicing multiple discs you will need multiple sets of brake pads.

RMSTATOR is specialized in designing and manufacturing innovative electrical and electronic components for Powersports vehicles like motorcycles, ATV, SxS, UTV, snowmobiles, and PWC. Through unrelenting quality control, we ensure that each component meets or exceeds the OEM specs. With over 25 product families, rest assured that you will find the part you need.

• Direct replacement to your original unit
• Plug-and-play, direct fit, easy installation
• Highest grade of lamination materials
• Highest grade of copper winding, resistant to 200 degrees Celsius
• Connector included
• Includes a two-year warranty

Battery condition is extremely important. No stator can work correctly with a bad or weak battery. Always fully charge your battery before performing any charging system tests or replacing parts. If there is any doubt, have the battery load tested or replaced.

Please Note:

1. All electrical components must be fitted by a qualified technician.
2. Before fitting electrical components ensure the root cause of the original failure has been addressed.
3. The absence of either of points 1 or 2 above, will void any warranty.

MTX solid discs are constructed using one complete segment of Japanese SUS 420 stainless steel, then heat-treated to HRC 36+-2. Lightening and drill hole patterns are as per OEM designs to improve braking performance and reduce the temperature of the disc.

MTX Discs provide amazing braking control for your motorcycle. All MTX discs are designed and manufactured with world-leading, cutting edge technologies:

• Precision CNC machined and laser-cut technology
• Japanese SUS 420 Stainless Steel
• Replacement for Original Equipment
• OEM Design; lightening & drill hole patterns

Specifications:

• O.D: 275mm
• I.D: 56mm
• Minimum Thickness: 4.5mm
• Disc Position: Front Right