HARD PARTS

Each pack of Premier CSK Clutch Springs contains a complete set of heavy-duty springs. Up to 15% stronger than the original.

Customer should be advised that after installation of a CSK kit the clutch lever will feel slightly ‘heavier’ than standard

A Quality Swing Arm Repair Kit from All Balls Racing containing everything required to rebuild swing arm bearings. Confirm suitability for your year, make, model prior to purchase.

Bushings are case-hardened and plated to prevent wear and corrosion. POM composite washer bearings replace thrust needle washers for superior resistance to water and dirt and increase service life. Shafts are made from 52100 Bearing steel, through hardened and precision ground. Needle Bearings are made from 52100 bearing steel and ARC61-65 heat treated ST13 steel shell.

Kit Contents:

• 2x Seals
• 2x Needle Bearings

Please Note:

1. All electrical components must be fitted by a qualified technician.
2. Before fitting electrical components ensure the root cause of the original failure has been addressed.
3. The absence of either of points 1 or 2 above, will void any warranty.

Hands down, the most complete line of linkage bearing and seal kits!

Kit contains all of the components required to properly rebuild the linkage bearing assembly. Needle bearing shafts are made with SCM415/42 bearing steel that has been hardened and precision ground.

All metal bushings are case-hardened and plated to prevent wear and corrosion.

POM composite washer bearings replace thru needle washers, increase service life, and add superb resistance to water and dirt.

The most convenient one-stop-shop for maintaining your motorcycle. Kits include front brake pads/shoes, rear brake pads/shoes, an air filter with 1L of filter oil and an oil filter where applicable.

This kit includes:

GF041S3 - BRAKE PADS GOLDFREN GF041-S3
GF346K5 - BRAKE PADS GOLDFREN GF346-K5
PUTAFBE8144 - PUTOLINE AIR FILTER BE8144
PTAAFO1L - PUTOLINE ACTION AIR FILTER OIL 1LT (70005) *12
MFO631 - MOTO-FILTER OIL FILTER (HF631) SINGLE

Quantum replacement fuel pumps, regulators, tank seals and strainers are designed to meet or exceed OEM specifications, and feature upgrades that improve on the OEM design. Upgraded polymers, brushes, and commutators ensure long life and durability in multiple fuel blends.

Features & Benefits

• OEM or better performance
• Polished corrosion-resistant case to help minimize seizing during non-operation
• Specifically designed for quiet operation
• Drop-in replacement
• Gradient density fuel strainer for superior contaminant filtration
• Patented check valve technology
• Compatible with modern ethanol-infused pump gasoline

Wossner

For more than 35 years, Wössner successfully design and produce high-performance pistons and connecting rods.

In order to offer their customers the best of Wössner Power, their products are produced by using state-of-the-art technology and are subject to continuous quality control.

Performance, quality and longevity - this is what Wössner stands for with high-quality products.

Con Rod Kits

The Wössner 2-stroke connecting rods are always supplied with lifting pins, needle bearings, connecting rod bearings and spacers.
The Wössner 4-stroke connecting rods include crank pins and connecting rod bearings.
Please use our Fitments Tool to ensure the correct part is ordered.

The All Balls CV Boot material is compounded from an OEM grade DCR66 rubber that is formulated specifically for the demanding requirements of today’s ATVs and UTVs.

• 40% higher tensile strength than conventional CV boo material, suitable for the high joint angles of modern ATVs and UTVs.
• 50% more abrasion-resistant than conventional CV boot material to ensure a long life in harsh off-road environments.
• Rubber compound is tested to -40° F to ensure good performance and long life at low temperatures.
• Lithium-based Molybdenum Grease insures good lubrication for long CV joint life. Easier to install than most OEM and aftermarket boots. Sold each. Does not require the use of a ""Banding Tool"".

Specifications:

• H: 97mm
• SD: 18mm
• LD: 64mm
• Shaft I.D.: 18
• CV Body I.D.: 64
• Length: 97

Kits include:

• Two stainless steel clamps that are designed to be tightened without the use of special tools.

Up to 40% stronger than OE axles, these complete axles feature enlarged CV joints, bearing cages, and chromoly axle shafts. All internal components are precision ground and utilize molybdenum grease.

Features:

• 40% stronger than OEM.
• Larger 4340 chrome-moly steel axle bar.
• Precision ground components.
• Low profile clamps.
• Neoprene boots.
• Engineered in the USA.
• Manufactured in an ISO facility.
• Assembled with 3% moly grease.
• Black oxide coating to resist rust and corrosion.

The All Balls CV Boot material is compounded from an OEM grade DCR66 rubber that is formulated specifically for the demanding requirements of today’s ATVs and UTVs.

• 40% higher tensile strength than conventional CV boo material, suitable for the high joint angles of modern ATVs and UTVs.
• 50% more abrasion-resistant than conventional CV boot material to ensure a long life in harsh off-road environments.
• Rubber compound is tested to -40° F to ensure good performance and long life at low temperatures.
• Lithium-based Molybdenum Grease insures good lubrication for long CV joint life. Easier to install than most OEM and aftermarket boots. Sold each. Does not require the use of a ""Banding Tool"".

Specifications:

• H: 92mm
• SD: 19mm
• LD: 66mm
• Shaft I.D.: 19
• CV Body I.D.: 66
• Length: 92

Kits include:

• Two stainless steel clamps that are designed to be tightened without the use of special tools.

Quality replacement components to rebuild one fuel tap. Improves service life and resistance to water and dirt.

Includes:

• Face screws
• Face gasket
• Wave washer
• Tank bolts
• Tank gasket
• O-rings

• Precision machined from high-grade 304 Stainless Steel.
• Stainless steel reduces thermal conductivity by up to 93% compared to aluminium.
• Plastic composite pistons are prone to damage and become brittle with age.
• OEM chrome-plated steel and aluminium pistons are prone to corrosion.
• Eliminates failure prone ceramic inserts found on some KTM models.
• Each kit contains piston or pistons to rebuild one caliper.

K&N's high-flow air filters are available as a replacement for your stock motorcycle air filter element. They are custom-engineered to fit your specific application and are designed to provide low restriction and increased performance while providing excellent engine protection for your motorcycle.

Features:

• Designed to provide increased horsepower and torque.
• Pleated media provides a large filtration area, offering long service intervals.
• Multiple layers of woven cotton gauze media offer excellent filtration.
• Application-specific base seal and sealing bead.
• Made in the USA for over 40 years.
• Washable and reusable, pre-oiled and ready to ride!

Specifications:

• Filte r Material: Cotton Gauze
• Washable: Yes
• Height: 41mm
• Filter Re-Oiling Amount: 8ml

P SERIES - Street Bikes

Premier's most successful general use material, our P series pads, are a tough Kevlar based organic material giving superb brake effect on all sportbikes and cruisers. This material is preselected by the catalogue when you order P prefix disc pads.

P SERIES - Off-Road

Part numbers relating to off-road machines are supplied in carbon graphite compound for medium durability, good brake effect and minimum heat generation.

Hex head flange bolts are made from zinc-plated 8.8 steel. Sold individually or in bags of 10.

Please Note:

1. All electrical components must be fitted by a qualified technician.
2. Before fitting electrical components ensure the root cause of the original failure has been addressed.
3. The absence of either of points 1 or 2 above, will void any warranty.

Quality carburettor rebuild kit from All Balls.

• Kits include all of the necessary components to repair a carburettor. ATV models with two carburettors include components to repair two carburettors.
• Kit includes necessary all O-rings, gaskets, jets, needle, mixture screw, float bowl screws, float valve needles and seat. (Needle jet and other pressed-in jets are not included in the kit.)
• OEM jet sizes are included in the kit. NBR rubber material is used on all O-rings and rubber gaskets NBR has excellent resistance to the ethanol used in today’s fuels.
• Applications that use paper float bowl gaskets are upgraded to High-Performance Interface Gasket material.
• Components included in the kits are based on US models and discretion must be used when attempting to install the kit on a non-US model.
• Off-road use only.

Bolt brand bolts, nuts and washers meet all OEM standards. Designed with precision, each bolt comes in a convenient pack of 10.

New from All Balls comes High Quality Carburetor Rebuild Kits. These kits contains everything required to rebuild your carburetor including seals, jets, needles, screws and other parts depending on model. These kits are a great solution as they contain all the parts you require in a quick and cost effective solution.

• Kits include all of the necessary components to repair a carburetor. ATV models with two carburetors include components to repair two carburetors.
• Kit includes necessary all O-rings, gaskets, jets, needle, mixture screw, float bowl screws, float valve needle and seat. (Needle jet and other pressed in jets are not included in kit.)
• OEM jet sizes are included in the kit. NBR rubber material is used on all O-rings and rubber gaskets NBR has excellent resistance to the ethanol used in today’s fuels.
• Applications that use paper float bowl gaskets are upgraded to High Performance Interface Gasket material.
• Components included in the kits are based off of US models and discretion must be used when attempting to install the kit on a non US model.
• Off road use only.

Please Note:

1. All electrical components must be fitted by a qualified technician.
2. Before fitting electrical components ensure the root cause of the original failure has been addressed.
3. The absence of either of points 1 or 2 above, will void any warranty.

Brand new ignition cap coil.

Features:

• Direct replacement to your original unit.
• Quality exceeds the OEM equipment.
• All shipped products are tested.
• Bracket centre to centre: 100 mm

Please Note:

1. All electrical components must be fitted by a qualified technician.
2. Before fitting electrical components ensure the root cause of the original failure has been addressed.
3. The absence of either of points 1 or 2 above, will void any warranty.

DUST SEAL KIT

A Quality Pair of Fork Dust Seals from All Balls Racing.

Use these Fork Dust Seals to keep dirt away from your Fork Oil Seals, making them last longer.

A short section of Nitromousse that increases the PSI feel and extend the lifetime of your Nitro Mousse. Available for multiple sizes of Platinum and Soft Nitro Mousse.

Kit includes water pump cover gasket or o-ring, water pump shaft bearing(s) and seal(s) to repair a leaking water pump seal and/or a failed bearing.

Features:

• Precision micro bearings provide OE quality and durability.
• High pressure/temperature mechanical and rubber seals.

RMSTATOR is specialized in designing and manufacturing innovative electrical and electronic components for Powersports vehicles like motorcycles, ATV, SxS, UTV, snowmobiles, and PWC. Through unrelenting quality control, we ensure that each component meets or exceeds the OEM specs. With over 25 product families, rest assured that you will find the part you need.

Features:

• RM STATOR's PeakRPM technology provid a more aggressive timing curve for increased throttle response.
• Ride at full throttle with our application-specific CDI box that raises the rev limiter by 1000 RPM.
• Enjoy fast and easy installation with our plug and play design and included dielectric connector grease.
• OEM-grade electronic components and printed circuit boards for long-term reliability and performance.
• 90% of ignition issues are caused by a faulty stator. Full test ignition components before buying.

Please Note:

1. All electrical components must be fitted by a qualified technician.
2. Before fitting electrical components ensure the root cause of the original failure has been addressed.
3. The absence of either of points 1 or 2 above, will void any warranty.