All Products

The Torque Mighty 15 Folding Multi-Tool includes 15 chrome vanadium tools. It has laser-etched graphics and lightweight 6061 aluminium sides.

Key Features:

• 2, 2.5, 3, 4, 5, 6, 8mm Hex keys.
  
  
• T25 Torx key.
  
  
• No.2 Cross head screwdriver.
  
  
• No.5 Flat head screwdriver.
  
  
• Chain tool.
  
  
• 14G, 15G, 16G, Mavic M7 spoke keys.

High-quality park hand brake cable from All Balls.

Features:

• Black PVC outer jacket for maximum flexibility and durability.
• Steel inner casing that is tightly coiled for low compression.
• A pre-lubricated nylon inner sleeve guarantees smooth operation and long life.
• All wire ends are bird caged prior to terminal casting for superior pull-out resistance.
• EPDM molded rubber components for high UV resistance and long life.
• Injected molded components are manufactured from high strength POM material.

Kit includes quantities required to replace all OEM seals.

The ultimate in cool kit!

When activated, the indicator dynamically sweeps across from the inside to the outside of the indicator strip.

Features

• Universal Fit
• Waterproof design
• E-mark approved, suitable for road use
• Sequential LED indicators
• Contains 7 LEDs behind a smoked lens, housed in a tough, matt black case
• Voltage 12V Power 2.4W
• M8 bolt - thread pitch 1.25

Size: 103mm (L) x 15mm (W) x 12mm (D)

Includes

• A right and left indicator (for front or rear use)
• 2 resistors to regulate the flash rate

Upgrade your motorcycle's clutch system with the All Balls Racing Motorcycle Clutch Cable. Designed with precision and durability in mind, this clutch cable delivers exceptional performance and reliability on the road.

• Black PVC outer jacket for maximum flexibility and durability.
• Steel inner casing that is tightly coiled for low compression.
• A pre-lubricated nylon inner sleeve guarantees smooth operation and long life.
• All wire ends are bird-caged prior to terminal casting for superior pull-out resistance.
• EPDM-moulded rubber components for high UV resistance and long life.
• Injected moulded components are manufactured from high-strength POM material.

Please Note:

1. All electrical components must be fitted by a qualified technician.
2. Before fitting electrical components ensure the root cause of the original failure has been addressed.
3. The absence of either of points 1 or 2 above, will void any warranty.

Quality Starter Brushes from J&N Electrical. Replace your worn-out starter motor brushes with these and get your starter motor running again.

Manufactured following strict OE standards to work like the original component.

Features:

• Engineered using the latest technology to ensure the product lasts longer in service.
• Engineered with a factory-like design for effortless installation, ensuring a perfect match with your vehicle.
• Made of high-quality components for durability, reliability, and performance.
• Designed specifically for trucks, trailers, and buses.

Note:

1. All electrical components must be fitted by a qualified technician.
2. Before fitting electrical components ensure the root cause of the original failure has been addressed.
3. The absence of either of points 1 or 2 above, will void any warranty.

Comprehensive kit for transmission rebuild, includes bearings, seals, o-rings, and shims.

• Affordable alternative to OEM replacement parts.
• Utilizes high-quality ABEC 3 precision ball bearings for durability and performance.
• Sourced components, including ball bearings, needle bearings, tapered bearings, PTFE lined bearings, seals, and o-rings, from reputable manufacturers worldwide.
• Kits with tapered bearings come with a selection of shims for customization.

Includes components necessary to complete a piston (top end) rebuild. Competitive pricing, made to meet and exceed OEM quality and designed as a direct OEM replacement.

Features:

• Designed for OEM replacement.
• Made from high-quality materials.
• Meet or exceed OEM specifications.
• Competitive pricing.

A quality caliper rebuild kit from All Balls. Contains everything needed to rebuild your caliper to like new condition.

Founded in 2008, Motobatt is a manufacturer of premium Powersports batteries, battery chargers and battery related accessories. Motobatt is the creator and holds patents all over the world for the Motobatt 4 terminal battery that facilitates flexible battery installation across a wide variety of vehicles while maintaining an OE like fit.

Features:

• Self Sensing Microprocessor
• 3 Step Algorithm
• Fully Automatic Charging & Maintaining
• Overcharge Protection
• Reverse Polarity Protection
• Short Circuit Protection
• Maintains Full Charge

Specifications:

• Application: 6V & 12V AGM, Lead-Acid, Calcium & Gel Batteries
• Input: Auto-switching 120-240VAC 50/60 Hz
• Output: Select 6V/12VDC 500mA
• Max Charge Current: 500mA
• Max Voltage: 7.4V (6V Battery), 14.7V (12V Battery)
• Battery Capacity: 2-20Ah (Charging), up to 50Ah (Maintenance)

Produced in the U.S.A. with the latest materials and technology in seal production to Vertex specifications. Vertex seals ensure long-lasting performance and leak prevention for your rebuild needs.

Features:

• OEM replacement mechanical water pump seal.
• High-quality seal face material seals better and lasts longer.
• Corrosion and chemical-resistant materials keep your engine clean, safe and cool.
• Meets or exceeds OEM quality.

NOTE: This complete Vertex Gasket Set contains all parts as pictured.

Produced in the U.S.A. with the latest materials and technology in gasket production to Vertex specifications. Vertex gaskets ensure long-lasting performance and leak prevention for your rebuild needs. Vertex's replacement gaskets and seals are available as top-end kits, complete engine kits, or as an oil seal kit.

• One kit containing all of the gaskets, O-rings, and valve seals necessary to rebuild the entire engine and transmission.
• Includes transmission seals.

Rack kit contains tie rod end and shaft that connect to the steering rack as well as the outer tie rod end, boot and the required hardware for one side.\

Applications:

• 2020 Polaris Ranger 1000 EPS
• 2020 Polaris Ranger Crew 1000 EPS
• 2020 Polaris Ranger Crew XP 1000 EPS Northstar HVAC Edition
• 2020 Polaris Ranger Crew XP 1000 EPS Texas Edition
• 2019 Polaris Ranger Crew XP 1000 EPS
• 2019 Polaris Ranger Crew XP 1000 EPS Northstar HVAC Edition
• 2018 Polaris Ranger Crew XP 1000 EPS Northstar HVAC Edition
• 2020 Polaris Ranger XP 1000 EPS Northstar HVAC Edition
• 2020 Polaris Ranger XP 1000 EPS Texas Edition

Replacing the fuel tank seal or gasket is a vital part of the fuel pump replacement process. Quantum tank seals are made exclusively from Viton, which are impervious to ethanol and other chemicals that degrade conventional rubber over time. These OE replacements are designed for fitment on specific vehicles.

Upgrade rubber bushings found in Utility ATV A-Arms to AB's redesigned HD Delrin bushings.

This kit is designed to replace worn-out rubber bushings and provides greater suspension travel and performance.

Quality design and construction of every All Balls piece meet the toughest standards and conditions - from daily commuting to full-on racing, all older bearing and seal designs are upgraded to the best and latest specs and designs.

NOTE: This Vertex Top End Gasket Set contains all components pictured.

Produced in the U.S.A. with the latest materials and technology in gasket production to Vertex specifications. Vertex gaskets ensure long-lasting performance and leak prevention for your rebuild needs. Vertex's replacement gaskets and seals are available as top-end kits, complete engine kits, or as an oil seal kit.

• These sets include the head, base, and exhaust gaskets, valve seals, O-rings and other gaskets to complete a top-end rebuild.

Ideal replacement for dirt bikes.

Features:

• Anti-swell alloy impregnated heavy-duty cork-based facings.
• Smooth clutch take up compared to paper clutches, which can ‘snatch’.
• Steel separator plates increase flywheel effect of the engine and improve performance.

Street Triple Standard

This part will only fit Street Triple Standard with a VIN HIGHER than 560477 and an engine number BETWEEN 616233 and 624372 or HIGHER than 626867. If your vehicle has a VIN HIGHER than 560477 and with an engine number LOWER than 616232 or BETWEEN 624373 and 626866, refer to RMS010-106948. If your vehicle has a VIN LOWER than 354281, please refer to RM01348. If your vehicle has a VIN BETWEEN 354282 and 560476, please refer to RM01389.

Street Triple R 2008 to 2020

This part will only fit Street Triple R with a VIN HIGHER than 560477 and an engine number BETWEEN 616233 and 624372 or HIGHER than 626867. If your vehicle does not correspond to the requirements above, refer to part # RMS010- 106948.

Battery condition is important. No stator can make up for a bad or weak battery. If in doubt charge your battery and have it load tested, or simply replace it. ALWAYS START WITH A FULLY CHARGED BATTERY!

This special regulator bypasses the vehicle’s failure-prone wiring harness between the regulator and battery, and instead connects directly to the battery with ring terminals for the best possible connection. For Triumph fitments please check your stator to regulator connector as there were 2 versions used and select the correct one. Our possible part numbers are :

• RMS022-106222

• RM S022-107616

Battery condition is extremely important. No voltage regulator can work correctly with a bad or weak battery. Always fully charge your battery before performing any charging system tests or replacing parts. If there is any doubt, have the battery load tested or replaced.

Specifications:

Stator:

• Dimensions:
  • Interior diameter: 42 mm
  • Exterior diameter: 115 mm
  • Thickness: 18 mm
  • Length of wires stator to grommet: 100 mm
  • Length of wires grommet to plug: 200 mm
• Other specifications:
  • Number of wires: 3
  • Number of plugs: 1
  • Number of pins: 3
  • Number of poles: 18
  • Wire to wire resistance:
    • Alternator: Black to Black = 0.6 ohms +-20%
    • Alternator to ground = O.L

RMSTATOR Red Machined Aluminum Mosfet Voltage Regulator Rectifier:

• Dimensions:
  • Width: 95 mm
  • Length: 90 mm
  • Height: 30 mm
  • Wires length: 1010 mm & 350 mm
  • Fixation holes centre to centre: 75 mm
• Other specifications:
  • Number of plugs: 2
  • Number of pins: 5
  • Number of wires: 5
  • Minimum Charging Voltage: 14.5 V +/- 0.5 V
  • Maximum Charging Current: 50 A / 500 W
  • Open Circuit Voltage: < 15 V
  • Operation Temperature: -20° to 85°

The right tools always help to get the job done quicker and the Brush and Scrub Set does just that.

From cleaning delicate paintwork to tackling grime-clad, hard-to-reach areas this set has a solution for every challenge. Use in combination with our Mint Cleaning and Detailing range to keep your bike minty clean and 'best in show'.

The Big Softie is a large, soft cleaning brush, angled for easy use. Its big head gently loosens dirt and rubberised impact zones protect paintwork, so you can blitz your bike in no time at all.

For cleaning wheels, rims and spokes there are two differently shaped brushes: Wheely Clean is long, wide and soft, while the Double Stubble has short high density bristles. Together dirt stands no chance of staying put.

There's no escape from the Prong Brush as it tackles dirty parts from both sides at once, dislodging hard-to-reach debris with its twin- headed design.

Features:

• Includes: Big Softie, Wheely Clean, Double Stubble and Prong Brush
• Durable nylon bristles
• Rubberised safety tips
• Long reach brush head
• Tough impact-resistant handles

Brand new aftermarket Stator + Crankcase Cover Gasket + Mosfet Voltage Regulator Kit

• Direct replacement to your original unit
• Plug-and-play, direct fit, easy installation
• All products shipped are tested

We have even included the opposite connector (main harness side) as we know these are often melted / corroded / defective and a major cause of repetitive electrical issues.

All item pictures are accurate; if in doubt do not hesitate to compare our item to your original part.

Stator:

• Highest-grade lamination materials
• Highest-grade copper windings, resistant to 200 degrees Celsius.
• Stator crankcase cover gasket included
• Connector included
• Rubber grommet included

Brand new RMSTATOR Red Machined Aluminum Mosfet Regulator

Our new RMSTATOR machined aluminum Mosfet voltage regulator is a great upgrade for heat dissipation in any powersports charging system. After 10 minutes of use, our billet aluminum heatsink runs cooler by 33% than standard cast regulator housings. Our new RMSTATOR red regulator, equipped with the renowned Mosfet regulation technology, is an added value to any three- phase permanent magnet charging system.

STOP BURNING YOUR REGULATOR RECTIFIER!

It is time to update or replace your voltage regulator with the advanced MOSFET type.

It runs cooler than all OEM diode style regulators. In addition, this rectifier has overheat protection, rather than burn up, it will simply turn off for a while and cool off.

• The quality exceeds the OEM equipment
• Improved heat sink and charging capabilities
• Higher grade of electric components

Why use Mosfet Enhanced technology?

• Runs cooler: Runs much cooler than the traditional Shunt voltage regulator rectifier.
• Saves gas: Less load on the stator, less work, less fuel is used and you save.
• Regulated energy: The power charging your battery is steadier and smooth.
• Extended battery life: Extends the battery’s life and cold cranking capacity.
• More engine power: Removes stator load resulting in more engine power.
• Optimized power: Optimize power delivery by switching the stator coils on or off.

With Enhanced Technology Design

This product is an advanced design that lowers operating temperatures for extended longevity and better performance than the OEM part.

Specifications:

• Dim ensions Stator:
• Interior diameter: 38 mm
• Exterior diameter: 107 mm
• Thickness: 12 mm
• Length of wires stator to grommet: 160 mm
• Length of wires grommet to plug: 330 mm
• Other specifications:
• Number of wires: 3
• Number of plugs: 1
• Number of pins: 3
• Wire-to-wire resistance:
• Alternator: Yellow to Yellow = 0.5 ohms +/-20%
• Regulator dimension:
• Width: 92 mm
• Length: 92 mm
• Height: 30 mm
• Fixation holes center to center: 75 mm
• Wires length: 300 mm
• Other specifications:
• Number of plugs: 2
• Number of pins: 7
• Number of wires: 7
• Minimum Charging Voltage: 14.5 V +/- 0.5 V
• Maximum Charging Current: 50 A / 500 W
• Open Circuit Voltage: < 15 V
• Operation Temperature: -20° C to 85° C

Note: Battery condition is extremely important. No stator can work correctly with a bad or weak battery. Always fully charge your battery before performing any charging system tests or replacing parts. If there is any doubt, have the battery load tested or replaced.

Celebrate being part of the coolest family on earth with our collection of biker signs.

Whether you commute to work on a sensible 125, cross continents on a metal mule or tear up the weekend streets on your pride and joy... you belong.

With pre-drilled holes for mounting, Oxford's Garage Signs are also the perfect gift for the biker who's got it all!

Features:

• Indoor use only.
• Made from high quality coated metal tin plate with rolled edges.
• 4 x 3.2mm pre-drilled holes for attachment.
• Dimensions - 30 x 20cm x 0.25mm thick.
• Weight - 124g
• Different styles and mottos available.

Up to 40% stronger than OE axles, these complete axles feature enlarged CV joints, bearing cages, and chromoly axle shafts. All internal components are precision ground and utilize molybdenum grease.

Features:

• 40% stronger than OEM.
• Larger 4340 chrome-moly steel axle bar.
• Precision ground components.
• Low profile clamps.
• Neoprene boots.
• Engineered in the USA.
• Manufactured in an ISO facility.
• Assembled with 3% moly grease.
• Black oxide coating to resist rust and corrosion.

RMSTATOR is specialized in designing and manufacturing innovative electrical and electronic components for Powersports vehicles like motorcycles, ATV, SxS, UTV, snowmobiles, and PWC. Through unrelenting quality control, we ensure that each component meets or exceeds the OEM specs. With over 25 product families, rest assured that you will find the part you need.

• Direct replacement to your original unit
• Plug-and-play, direct fit, easy installation
• Highest grade of lamination materials
• Highest grade of copper winding, resistant to 200 degrees Celsius
• Connector included

Battery condition is extremely important. No stator can work correctly with a bad or weak battery. Always fully charge your battery before performing any charging system tests or replacing parts. If there is any doubt, have the battery load tested or replaced.

Please Note:

1. All electrical components must be fitted by a qualified technician.
2. Before fitting electrical components ensure the root cause of the original failure has been addressed.
3. The absence of either of points 1 or 2 above, will void any warranty.

Oblong key blank for the following Oxford locks.

• OF161 HD Mini / OF157>LK146 HD Chain Locks
• OF163 Barrier Chain
• OF172/173 Magnum U-lock
• Old Monster/Enigma
• LK340-4 Shackle14
• LK337-9 Sentinel
• LK143 ScootChain
• LK140 Chain8
• LK144 Chain10

Dimensions:

32 x 2.76 x 6.5 x 1.9mm

The Oxford 3 metre extension lead is suitable for up to 5amps.