All Products

HFP replacement fuel pumps, modules, assemblies, and kit components are designed to meet or exceed OEM specifications, and feature upgrades that improve on the OEM design. Upgraded polymers, brushes, and commutators ensure long life and durability in multiple fuel blends.

• OEM or better performance
• Polished corrosion-resistant case to help minimize seizing during non-operation
• Specifically designed for quiet operation
• Drop-in replacement
• Gradient density fuel strainer for superior contaminant filtration
• Patented check valve technology
• Compatible with modern ethanol-infused pump gasoline

With certain BMW motorcycle models, the spark plug caps and coils are combined to reduce the number of parts used in order to improve efficiency. However, when the spark plug cap wears out, the cost of the replacement becomes more expensive. If you are experiencing ignition problems, this could mean the ignition cap coil needs to be replaced. Simple, easy to install, affordable, and improves engine performance.

Features:

• Direct replacement to your original unit.
• Quality exceeds the OEM equipment.
• All products shipped are tested.

Specifications:

• Len gth: 121 mm
• Number of pins: 3
• Number of terminals: 1
• Resistance: 1.4 ohm

Note: All item pictures are accurate. If in doubt, do not hesitate and compare our item to your original part.

K&N's high-flow air filters are available as a replacement for your stock motorcycle air filter element. They are custom-engineered to fit your specific application and are designed to provide low restriction and increased performance, while providing excellent engine protection for your motorcycle.

Features:

• Designed to provide increased horsepower and torque.
• Pleated media provides a large filtration area, offering long service intervals.
• Multiple layers of woven cotton gauze media offer excellent filtration.
• Application-specific base seal and sealing bead.
• Made in the USA for over 40 years.
• Washable and reusable, pre-oiled and ready to ride!

Specifications:

• Washa ble: Yes
• Filter Material: Cotton Gauze
• Height: 149mm
• Inside Diameter: 52mm
• Outside Diameter: 102mm
• Filter Re-Oiling Amount: 34ml

Rough riding calls for stronger axles and that’s where All Balls Racing excels. Machined for exact OEM fit, the shaft is made of chromoly steel with a larger diameter than most axles. The axle has 6 ball bearings in each CV joint. Laminate coating resists corrosion and rust, and protects axle from dirt, water, rocks and grease. Waterproof neoprene boots act as a first line of defense, shielding vulnerable joints and preventing leaks. High performance molybdenum grease reduces heat and friction.

• In static torsion trials, these axles were up to 30% stronger than OEM and aftermarket competition.
• Lasts approximately 50 percent longer than many aftermarket competitors.
• Typically runs almost 130,000 cycles versus 80,000 cycles for many axles.

Features:

• 40% stronger than OEM.
• Larger 4340 chrome-moly steel axle bar.
• Precision ground components.
• Low profile clamps.
• Neoprene boots.
• Engineered in the USA.
• Manufactured in an ISO facility.
• Assembled with 3% molybdenum grease.

Wrench Rabbit Rebuild Kits have been rebranded to Vertex Rebuild Kits; all components remain unchanged however you may receive a kit that is boxed differently to the one pictured.

Vertex Complete Engine Rebuild Kits are a simple and cost-effective way to complete a top-to-bottom professional rebuild for your 2 or 4-stroke motorcycle or ATV/UTV. The one easy to order kit will not only save you time by offering a one-stop-shop in a box, but they also save you money when compared to purchasing all items individually.

Vertex kits include quality components from Vertex, Hot Rods & Hot Cams.*

All parts are manufactured in the USA from the highest quality material.

Features:

• Crafted to deliver unbeatable levels of quality
• High-grade materials for exceptional performance
• Superior in durability and reliability
• Kits available for many 2 & 4-stroke motorcycles, ATVs & UTVs
• Cost-effective solution
• Saves time sourcing individual components
• Vertex pistons & gaskets*
• Hot Rods crank & bearing kits*
• Hot Cams cam chain*

Includes:

• Crankshaft
• Piston Kit
• Complete Engine Gasket Kit
• Oil Seal Kit
• Main Bearing and Seal Kit
• Water Pump Rebuild Kit
• Transmission Bearing Kit
• Countershaft Bushing/Seal Kit
• Cam Chain

*Specific parts vary by kit (see included parts above).

Please Note:

1. All electrical components must be fitted by a qualified technician.
2. Before fitting electrical components ensure the root cause of the original failure has been addressed.
3. The absence of either of points 1 or 2 above, will void any warranty.

Quality pair of fork oil seals from All Balls Racing.

Features:

• Dyno tested to last 3 to 4 times longer than OEM seals.
• Directional ribs on outside of seal allow seal to be installed easily.
• Dual-sealing lips guarantee oil stays in and dirt stays out.

All Balls Choke Plunger Kit

- Choke plunger rebuild kits are intended to be used as a repair kit only.
- Kit contents will vary and may include o-rings, springs, retaining nuts, boots and cable guides as necessary.
- Choke plungers can seize or can easily be lost during a carburetor rebuild.
- Improperly functioning parts can cause hard starting or poor running conditions.
- Models with multiple carburetors include components to repair each choke plunger.

Iridium BLUE visor for LS2 FF805 helmet.

Anti-scratch, optically correct, and uses a quick removable tool-less shield system.

Upgrade your motorcycle's clutch system with the All Balls Racing Motorcycle Clutch Cable. Designed with precision and durability in mind, this clutch cable delivers exceptional performance and reliability on the road.

• Black PVC outer jacket for maximum flexibility and durability.
• Steel inner casing that is tightly coiled for low compression.
• A pre-lubricated nylon inner sleeve guarantees smooth operation and long life.
• All wire ends are bird-caged prior to terminal casting for superior pull-out resistance.
• EPDM-moulded rubber components for high UV resistance and long life.
• Injected moulded components are manufactured from high-strength POM material.

P SERIES - Street Bikes

Premier's most successful general use material, our P series pads, are a tough Kevlar based organic material giving superb brake effect on all sportbikes and cruisers. This material is preselected by the catalogue when you order P prefix disc pads.

P SERIES - Off-Road

Part numbers relating to off-road machines are supplied in carbon graphite compound for medium durability, good brake effect and minimum heat generation.

GOLDfren began manufacturing sintered disc brake pads for a wide range of off-road and road motorcycles in 1991, nearly three decades on from their first motorcycle brake pads GOLDfren has become one of the largest aftermarket manufacturers in the motorcycle brake disc pad industry. Their development of next-generation products has kept them at the technological forefront of Sintered Friction Braking providing you with confidence in the performance, durability and reliability of your brakes.

S3 Series:

The S3 sintered compound is optimal in dry and wet conditions for road & off-road motorcycles. For the road application, S3 pads are suitable for both the front and rear brake while on off-road applications the S3 is only recommended for the front brake. The S3 series is designed for low abrasive interaction with the rotor and quieter braking due to the ceramic composite material. It has an HH friction rating and performs better at higher temperatures than the AD compound. Friction materials contain metal-ceramic with a bronze-graphite and non-metallic friction additives are spread evenly on the base fine bronze body to achieve optimal friction properties.

Features:

• Very high static friction coefficient
• Minimal difference between wet and dry braking performance
• Good abrasive resistance
• Low abrasive interaction with the brake rotor material
• Longer life compared to organic and Kevlar composite materials

Application:

• For riders who demand a bit more than average from their bikes
• Recommended on both front and rear brakes (road application)
• Can also be used on the front brakes of off-road bikes and ATVs
• Works well on both dry and wet conditions

Operating Parameters:

• Specific pressure: 3.0 Mpa
• Sliding speed: 45 m/s
• Constant maximum temp: 450°C
• Short time maximum temp: 800°C
• Counter-surfaces: steel disks

What is a sintered brake pad?

GOLDfren only manufacturers sintered brake pads that contain metal-ceramic and ceramic-carbon friction materials, these materials allow for less brake dust and a quieter braking experience. Sintered brake pads are made by fusing together metallic particles under high temperature and pressure which enhances friction properties and pad life, resulting in longer life and stronger braking. Sintered brake pads experience no brake fade when operating at high temperatures and in wet conditions. They also last up to 5 times longer than organic pads and provide additional braking strength. All materials used are environmentally friendly and do not contain any lead, asbestos, fibreglass or formaldehyde.

Reminder: one set of brake pads services one brake disc, if you are servicing multiple discs you will need multiple sets of brake pads.

This heavy-duty ball joint kit is engineered for those who demand reliability and strength in their vehicle's components.

Features:

• Heavy-duty steel housing.
• POM-M90 bearing cup to isolate the ball end from the steel housing for longer life.
• Steel-on-steel design with an adjustable cap and a grease zerk.
• Adjustable end cap allows slop to be taken up as the ball joint wears.

Each bike manufacturer uses different connectors for their indicators. This means that when fitting universal aftermarket indicators you need to cut the original connectors off and replace them with bullet fittings.

Not any more! Simply connect the IndyLeads between the original connector and the universal connector. Simple.

2 pack for front OR rear.

Quality carburettor rebuild kit from All Balls.

• Kits include all of the necessary components to repair a carburettor. ATV models with two carburettors include components to repair two carburettors.
• Kit includes necessary all O-rings, gaskets, jets, needle, mixture screw, float bowl screws, float valve needles and seat. (Needle jet and other pressed-in jets are not included in the kit.)
• OEM jet sizes are included in the kit. NBR rubber material is used on all O-rings and rubber gaskets NBR has excellent resistance to the ethanol used in today’s fuels.
• Applications that use paper float bowl gaskets are upgraded to High-Performance Interface Gasket material.
• Components included in the kits are based on US models and discretion must be used when attempting to install the kit on a non-US model.
• Off-road use only.

A premium single bar end mirror machined from billet aluminium. Easily adjustable and featuring anti-glare convex glass this mirror is designed to fit 22mm / 7/8" handlebars.

Features:

• Can be fitted above or below handlebar
• Suitable for all motorcycle types
• Machined from billet aluminium
• Anti-glare convex glass
• 70mm diameter mirror
• 12 - 18mm expansion bushes
• Easily adjustable
• Universal fitting
• To be used in conjunction with original-fit mirrors.

Vertex valves follow high-end OE specifications, using steel or titanium with a pressurised hardness treatment.

• Follows high-end OE specifications.
• High-quality steel or titanium valves.

Kit contains bearings, seals, and o-rings required to rebuild the transaxle.

Features:

• Direct OEM replacement at a fraction of the cost.
• High-quality ABEC 3 precision ball bearings used throughout.

Stronger and much safer than a bungee, Oxford's Atlas Straps are adjustable self-tensioning straps. Their extra strong, flat webbed design is easy to adjust to the desired length and the quick-release B-clip makes them simple to detach. The strap has an elasticated section which keeps the strap under constant tension providing a safer and more secure hold compared to regular solid straps.

With a multitude of uses, your gear will stay safe and secure with Atlas Straps.

Features:

• Extra strong construction.
• Durable elasticated straps.
• Quick-release premium buckle for extra durability.
• Adjustable length.
• Safe and secure.
• Anti-rust, anti-scratch, no sharp bungee hooks.
• Easy to use: attach, clip, tighten.
• Multiple uses: motorcycling, cycling, and outdoor leisure activities.
• Size options: 17mm or 26mm widths and 1.2m or 2.0m lengths.
• Available colourways: black, asphalt, lichen.
• 2 x straps per pack.

Warning:

DO NOT overstretch. Maximum stretch 50%. Always keep out of recoil path. Do not use if strap has any signs of damage. Check for damage before each use.

NOTE: This Vertex Top End Gasket Set contains all components pictured.

Produced in the U.S.A. with the latest materials and technology in gasket production to Vertex specifications. Vertex gaskets ensure long-lasting performance and leak prevention for your rebuild needs. Vertex's replacement gaskets and seals are available as top-end kits, complete engine kits, or as an oil seal kit.

• These sets include the head, base, and exhaust gaskets, valve seals, O-rings and other gaskets to complete a top-end rebuild.

All the bearings and seal required to refit a wheel in one convenient package.

Features:

• Premium high-speed bearings feature low drag.
• Double lip seals on both sides to provide superior exclusion of water and dirt
• Improved grease retention.

Oxford Hot Grips are the perfect accessory for maintaining warm hands all year round, perfect for using your summer gloves throughout winter or providing some additional warmth in summer. Oxford's new EVO Hot Grips include the all-new Thermistor controller, providing a clean and easy-to-read display with an upgraded 6-core over-moulded entry for additional strength and durability. Waterproof screw connectors are IP67 rated while a new wiring layout provides consistent heating throughout the grip. The Hot Grips have 5 heat levels ranging from 35°C to 45°C, allowing you to dial in the perfect temperature for every condition and setup. All Oxford Hot Grips have a battery-saving mode that automatically turns off the grips if you forget to, preventing permanent battery damage.

Features:

• Grip length can be trimmed if required.
• Intelligent Thermistor heat controller included.
• 5 heat settings give the perfect operating temperature.
• Battery saving mode prevents permanent battery damage.
• Sealed for life double bonded rainproof switch that draws under 4A.
• Soft, ultra-grippy diamond tread is inspired by race grips for comfort and feedback.
• 123mm grip length can be cleanly cut down to 114mm.

Note:

Oxford recommends plugging in and heating the Hot Grips BEFORE installation. This allows the grips to fit over the throttle tube more easily.

Quality pair of fork oil seals from All Balls Racing.

Features:

• Dyno tested to last 3 to 4 times longer than OEM seals.
• Directional ribs on outside of seal allow seal to be installed easily.
• Dual-sealing lips guarantee oil stays in and dirt stays out.

The WMP Swing Arm Kit includes all bearings seals, shafts, bushings and thrust bearings to completely replace and repair your swingarm bearings. All bearing shafts are constructed from hardened 52100 bearing steel, while all steel spacers are case-hardened and plated for durability and corrosion resistance.

Features:

• Complete OEM replacement bearing kit.
• Bearing shafts are constructed from hardened 52100 bearing steel.
• Steel spacers are case-hardened and plated.
• Includes all components for complete replacement.

Kit includes case-hardened bushing, replacement outer seal along with any O-rings, snap rings or lock washers required to complete the repair.

Features:

• Hardened bushings reduce wear and seal damage.
• Upgraded seal material reduces bushing wear and increases life.
• Brushing coating reduces corrosion.

Note: Verify fitment before purchasing.