HARD PARTS

Oxford Premium LED Turn Signals are compact, bright and sold with resistors (in case you need to adjust your flash rate).

Features:

• LED array.
• Matte black finish.
• Waterproof.
• Short stem.
• Includes resistors (optional, if needed).
• Sold as a pair.

Rough riding calls for stronger axles and that’s where All Balls Racing excels. Machined for exact OEM fit, the shaft is made of chromoly steel with a larger diameter than most axles. The axle has 6 ball bearings in each CV joint. Laminate coating resists corrosion and rust and protects axles from dirt, water, rocks and grease. Waterproof neoprene boots act as a first line of defence, shielding vulnerable joints and preventing leaks. High-performance molybdenum grease reduces heat and friction.

In static torsion trials, these axles were up to 30% stronger than OEM and aftermarket competition.

Features:

• 40% stronger than OEM.
• Larger 4340 chrome-moly steel axle bar.
• Precision ground components.
• Low profile clamps.
• Lasts approximately 50 percent longer than many aftermarket competitors.
• Neoprene boots.
• Typically runs almost 130,000 cycles versus 80,000 cycles for many axles.
• Engineered in the USA.
• Manufactured in an ISO facility.Assembled with 3% molybdenum grease.

These piston kits ease the repair process by saving time and money. They come with everything needed to replace your piston, top-end gaskets, and wrist pin bearing (for two strokes) when the time comes.

Features:

• Included are the piston, rings, wrist pin, circlips, top end gaskets, and even wrist pin bearing (for two-stroke applications).
• Four-stroke kits include a free camchain.
• Case-hardened and highly wear-resistant wrist pins have anti-galling properties.

Quality replacement components to rebuild one fuel tap. Improves service life and resistance to water and dirt.

Includes:

• Face screws
• Face gasket
• Wave washer
• Tank bolts
• Tank gasket
• O-rings

Quantum OEM replacement fuel pressure regulators restore OE pressure to your fuel system. Built to last and backed by a lifetime warranty.

Features:

• 50 PSI.
• OEM or better performance.
• Drop-in replacement.
• Compatible with modern ethanol-infused pump gasoline.

Vertex valves follow high-end OE specifications, using steel or titanium with a pressurised hardness treatment.

• Follows high-end OE specifications.
• High-quality steel or titanium valves.

Quality design and construction of every All Balls piece meets the toughest standards and conditions - from daily commuting to full-on racing, all older bearing and seal designs are upgraded to the best and latest specs and designs.

Available individually in left-hand and right-hand thread or sold in pairs one L/H and one R/H thread.

The HFP-181 is a replacement external (frame mounted) fuel pump for carbureted motorcycle applications.  This pump kit provides the exact pressure and volume as required by Honda, Kawasaki, KTM, Suzuki, and Yamaha motorcycle applications.

• OEM or better performance
• Polished corrosion-resistant case to help minimize seizing during non-operation
• Specifically designed for quiet operation
• Drop-in replacement
• Gradient density fuel strainer for superior contaminant filtration
• Patented check valve technology
• Compatible with modern ethanol-infused pump gasoline

A 2-wire replacement external (frame-mounted) fuel pump for carbureted motorcycle applications. This pump kit provides the exact pressure and volume as required by OEM motorcycle applications. Quantum replacement fuel pumps are designed to meet or exceed OEM specifications, and feature upgrades that improve on the OEM design. Upgraded polymers, brushes, and commutators ensure long life and durability in multiple fuel blends.

Features:

• OEM or better performance.
• Polished corrosion-resistant case to help minimise seizing during non-operation.
• Specifically designed for quiet operation.
• Drop-in replacement.
• Patented check valve technology.
• Compatible with modern ethanol-infused pump gasoline.

GOLDfren began manufacturing sintered disc brake pads for a wide range of off-road and road motorcycles in 1991, nearly three decades on from their first motorcycle brake pads GOLDfren has become one of the largest aftermarket manufacturers in the motorcycle brake disc pad industry. Their development of next-generation products has kept them at the technological forefront of Sintered Friction Braking providing you with confidence in the performance, durability and reliability of your brakes.

K5 Series:

The K5 sintered compound is optimal for off-road motorcycles and ATVs. It is recommended for riders who demand great off-road stopping power and brake pad durability when riding on tough off-road terrains. The K5 series is designed for low abrasive interaction with the rotor, long life and self-cleaning capabilities necessary in off-road riding conditions. Friction materials contain metal-ceramic with a sophisticated bronze-graphite and full-metal mixture formulation with fine friction particles to achieve optimal friction properties.

Features:

• High static friction coefficient
• Good abrasive resistance
• Self-cleaning capability
• Low abrasive interaction with the brake rotor material
• Up to 3 times longer operational life compared to organic and Kevlar composite materials

Application:

• Developed specifically for off-road motorcycles & ATVs
• Can be used on both front and rear brakes
• Could be used on the rear brake of road racing motorcycles

Operating Parameters:

• Specific pressure: 2.0 Mpa
• Sliding velocity: 20 m/s
• Constant maximum temp: 500°C
• Short time maximum temp: 750°C
• Counter-surfaces: steel disks

What is a sintered brake pad?

GOLDfren only manufacturers sintered brake pads that contain metal-ceramic and ceramic-carbon friction materials, these materials allow for less brake dust and a quieter braking experience. Sintered brake pads are made by fusing together metallic particles under high temperature and pressure which enhances friction properties and pad life, resulting in longer life and stronger braking. Sintered brake pads experience no brake fade when operating at high temperatures and in wet conditions. They also last up to 5 times longer than organic pads and provide additional braking strength. All materials used are environmentally friendly and do not contain any lead, asbestos, fibreglass or formaldehyde.

Reminder: one set of brake pads services one brake disc, if you are servicing multiple discs you will need multiple sets of brake pads.

NOTE: This Vertex Oil Seal Set contains all components pictured.

Produced in the U.S.A. with the latest materials and technology in gasket production to Vertex specifications. Vertex gaskets ensure long-lasting performance and leak prevention for your rebuild needs. Vertex's replacement gaskets and seals are available as top-end kits, complete engine kits, or as an oil seal kit.

• These sets include all oil seals necessary to rebuild the engine and transmission including crankshaft, output shaft, water pump, clutch, and shifter seals.

High-quality park hand brake cable from All Balls.

Features:

• Black PVC outer jacket for maximum flexibility and durability.
• Steel inner casing that is tightly coiled for low compression.
• A pre-lubricated nylon inner sleeve guarantees smooth operation and long life.
• All wire ends are bird caged prior to terminal casting for superior pull-out resistance.
• EPDM molded rubber components for high UV resistance and long life.
• Injected molded components are manufactured from high strength POM material.

Upgrade your motorcycle's clutch system with the All Balls Racing Motorcycle Clutch Cable. Designed with precision and durability in mind, this clutch cable delivers exceptional performance and reliability on the road.

• Black PVC outer jacket for maximum flexibility and durability.
• Steel inner casing that is tightly coiled for low compression.
• A pre-lubricated nylon inner sleeve guarantees smooth operation and long life.
• All wire ends are bird-caged prior to terminal casting for superior pull-out resistance.
• EPDM-moulded rubber components for high UV resistance and long life.
• Injected moulded components are manufactured from high-strength POM material.

GOLDfren began manufacturing sintered disc brake pads for a wide range of off-road and road motorcycles in 1991, nearly three decades on from their first motorcycle brake pads GOLDfren has become one of the largest aftermarket manufacturers in the motorcycle brake disc pad industry. Their development of next-generation products has kept them at the technological forefront of Sintered Friction Braking providing you with confidence in the performance, durability and reliability of your brakes.

S3 Series:

The S3 sintered compound is optimal in dry and wet conditions for road & off-road motorcycles. For the road application, S3 pads are suitable for both the front and rear brake while on off-road applications the S3 is only recommended for the front brake. The S3 series is designed for low abrasive interaction with the rotor and quieter braking due to the ceramic composite material. It has an HH friction rating and performs better at higher temperatures than the AD compound. Friction materials contain metal-ceramic with a bronze-graphite and non-metallic friction additives are spread evenly on the base fine bronze body to achieve optimal friction properties.

Features:

• Very high static friction coefficient
• Minimal difference between wet and dry braking performance
• Good abrasive resistance
• Low abrasive interaction with the brake rotor material
• Longer life compared to organic and Kevlar composite materials

Application:

• For riders who demand a bit more than average from their bikes
• Recommended on both front and rear brakes (road application)
• Can also be used on the front brakes of off-road bikes and ATVs
• Works well on both dry and wet conditions

Operating Parameters:

• Specific pressure: 3.0 Mpa
• Sliding speed: 45 m/s
• Constant maximum temp: 450°C
• Short time maximum temp: 800°C
• Counter-surfaces: steel disks

What is a sintered brake pad?

GOLDfren only manufacturers sintered brake pads that contain metal-ceramic and ceramic-carbon friction materials, these materials allow for less brake dust and a quieter braking experience. Sintered brake pads are made by fusing together metallic particles under high temperature and pressure which enhances friction properties and pad life, resulting in longer life and stronger braking. Sintered brake pads experience no brake fade when operating at high temperatures and in wet conditions. They also last up to 5 times longer than organic pads and provide additional braking strength. All materials used are environmentally friendly and do not contain any lead, asbestos, fibreglass or formaldehyde.

Reminder: one set of brake pads services one brake disc, if you are servicing multiple discs you will need multiple sets of brake pads.

PH SERIES – Street Sport “Sintered”

High-performance HH friction rated sintered metal pads made in the USA to an exclusive Premier formulation. PH brake pads offer maximum durability and unbeatable performance under heavy braking and high-speed use. Available for part numbers shown below - prefix with “PH to specify. PH series is no longer available for off-road applications following the formulation improvements of the PR range for Moto-X and ATV applications.

The surface mounted TTO Digital tach-hour Gauge allows you to easily monitor RPM and hours of use.

Specifications:

• Large readable display allows you to easily monitor your engine's running hours up to 99,999 total hours ensuring that you perform proper maintenance on your engine.
• The LCD display lets you to easily view all gauge readings regardless of the angle or lighting conditions.
• Tachometer from 0-19999 rpms
• Non-resetable hour meter from 0-99999 Hours
• Surface mount for easy install, comes with double sided VHB tape or can be bolted on
• Max RPM features
• Black case, orange version sold separate

What's in the box:

• TTO Tach Hour
• Screw Caps and VHB Tape, Use when not mounting with bolts

GOLDfren began manufacturing sintered disc brake pads for a wide range of off-road and road motorcycles in 1991, nearly three decades on from their first motorcycle brake pads GOLDfren has become one of the largest aftermarket manufacturers in the motorcycle brake disc pad industry. Their development of next-generation products has kept them at the technological forefront of Sintered Friction Braking providing you with confidence in the performance, durability and reliability of your brakes.

K5 Series:

The K5 sintered compound is optimal for off-road motorcycles and ATVs. It is recommended for riders who demand great off-road stopping power and brake pad durability when riding on tough off-road terrains. The K5 series is designed for low abrasive interaction with the rotor, long life and self-cleaning capabilities necessary in off-road riding conditions. Friction materials contain metal-ceramic with a sophisticated bronze-graphite and full-metal mixture formulation with fine friction particles to achieve optimal friction properties.

Features:

• High static friction coefficient
• Good abrasive resistance
• Self-cleaning capability
• Low abrasive interaction with the brake rotor material
• Up to 3 times longer operational life compared to organic and Kevlar composite materials

Application:

• Developed specifically for off-road motorcycles & ATVs
• Can be used on both front and rear brakes
• Could be used on the rear brake of road racing motorcycles

Operating Parameters:

• Specific pressure: 2.0 Mpa
• Sliding velocity: 20 m/s
• Constant maximum temp: 500°C
• Short time maximum temp: 750°C
• Counter-surfaces: steel disks

What is a sintered brake pad?

GOLDfren only manufacturers sintered brake pads that contain metal-ceramic and ceramic-carbon friction materials, these materials allow for less brake dust and a quieter braking experience. Sintered brake pads are made by fusing together metallic particles under high temperature and pressure which enhances friction properties and pad life, resulting in longer life and stronger braking. Sintered brake pads experience no brake fade when operating at high temperatures and in wet conditions. They also last up to 5 times longer than organic pads and provide additional braking strength. All materials used are environmentally friendly and do not contain any lead, asbestos, fibreglass or formaldehyde.

Reminder: one set of brake pads services one brake disc, if you are servicing multiple discs you will need multiple sets of brake pads.

P SERIES - Street Bikes

Premier's most successful general use material, our P series pads, are a tough Kevlar based organic material giving superb brake effect on all sportbikes and cruisers. This material is preselected by the catalogue when you order P prefix disc pads.

P SERIES - Off-Road

Part numbers relating to off-road machines are supplied in carbon graphite compound for medium durability, good brake effect and minimum heat generation.

Includes components necessary to complete a piston (top end) rebuild. Competitive pricing, made to meet and exceed OEM quality and designed as a direct OEM replacement.

Features:

• Designed for OEM replacement.
• Made from high-quality materials.
• Meet or exceed OEM specifications.
• Competitive pricing.

This DENALI Premium Wiring Harness features high-quality waterproof components and is designed to power two DENALI LED Light Pods. It features low- profile, water-tight connectors and premium moulded wire to ensure moisture is kept out of the system. The harness includes a completely sealed, waterproof switch that was engineered from the ground up to withstand harsh out-door abuse on powersports vehicles. It’s clever design can be either flush or bar mounted.

What’s In The Box?

• (x1) Premium Wiring Harness
• (x1) Single-Intensity Relay
• (x1) DrySeal™ ON-OFF Waterproof Illuminated Switch
• (x1) 7/8 inch Handlebar Switch Mount
• (x1) 1 inch Handlebar Switch Mount
• (x2) Self Tapping Screw
• (x1) Adhesive Pad
• (x4) Zip Ties

Ideal replacement for dirt bikes.

Features:

• Anti-swell alloy impregnated heavy-duty cork-based facings.
• Smooth clutch take up compared to paper clutches, which can ‘snatch’.
• Steel separator plates increase flywheel effect of the engine and improve performance.

Up to 40% stronger than OE axles, these complete axles feature enlarged CV joints, bearing cages, and chromoly axle shafts. All internal components are precision ground and utilize molybdenum grease.

Features:

• 40% stronger than OEM.
• Larger 4340 chrome-moly steel axle bar.
• Precision ground components.
• Low profile clamps.
• Neoprene boots.
• Engineered in the USA.
• Manufactured in an ISO facility.
• Assembled with 3% moly grease.
• Black oxide coating to resist rust and corrosion.

Carburetor repair kits
• Kits include all of the necessary components to repair a carburetor. ATV models with two carburetors include components to repair two carburetors.
• Kit includes necessary all O-rings, gaskets, jets, needle, mixture screw, float bowl screws, float valve needle and seat. (Needle jet and other pressed in jets are not included in kit.)
• OEM jet sizes are included in the kit. NBR rubber material is used on all O-rings and rubber gaskets NBR has excellent resistance to the ethanol used in today’s fuels.
• Applications that use paper float bowl gaskets are upgraded to High Performance Interface Gasket material.
• Components included in the kits are based off of US models and discretion must be used when attempting to install the kit on a non US model.
• Off road use only.

Ideal replacement for dirt bikes.

Features:

• Anti-swell alloy impregnated heavy-duty cork-based facings.
• Smooth clutch take up compared to paper clutches, which can ‘snatch’.
• Steel separator plates increase flywheel effect of the engine and improve performance.

PV SERIES – Semi-Sintered Pads

New high durability semi-sintered pads that have the brake response of an organic but the durability of a sintered pad. For sport bike use only.

Quality replacement components to rebuild one fuel tap. Improves service life and resistance to water and dirt.

Includes:

• Face screws
• Face gasket
• Wave washer
• Tank bolts
• Tank gasket
• O-rings

Crafted from military-spec certified TI3Al titanium alloy, Vertex Titanium Valves are made to endure the harshest racing conditions. Forged from a single blank, grain flow is improved to enhance the mechanical characteristics of the valve without having to resort to welding. Special PVD, CVD, and CrN coatings are used to provide low-friction surfaces that reduce heat generation and resist carbon build-up; coatings allow alloys like titanium to become ultra-smooth while reaching hardness levels 5x that of high-speed steel.

• Military-spec certified TI3Al titanium alloy
• Forged from a single blank
• PVD, CVD, and CrN coatings
• Reduces heat generation
• Resists carbon build-up
• Significantly stronger than steel

P SERIES - Street Bikes

Premier's most successful general use material, our P series pads, are a tough Kevlar based organic material giving superb brake effect on all sportbikes and cruisers. This material is preselected by the catalogue when you order P prefix disc pads.

P SERIES - Off-Road

Part numbers relating to off-road machines are supplied in carbon graphite compound for medium durability, good brake effect and minimum heat generation.

NOTE: This Vertex Top End Gasket Set contains all components pictured.

Produced in the U.S.A. with the latest materials and technology in gasket production to Vertex specifications. Vertex gaskets ensure long-lasting performance and leak prevention for your rebuild needs. Vertex's replacement gaskets and seals are available as top-end kits, complete engine kits, or as an oil seal kit.

• These sets include the head, base, and exhaust gaskets, valve seals, O-rings and other gaskets to complete a top-end rebuild.