HARD PARTS

These sets include all gaskets necessary to rebuild the engine and transmission.

Features:

• Restore performance and reliability.
• Produce more power, strength, and durability.
• Surpasses OE quality.

NOTE: This Vertex Top End Gasket Set contains all components pictured.

Produced in the U.S.A. with the latest materials and technology in gasket production to Vertex specifications. Vertex gaskets ensure long-lasting performance and leak prevention for your rebuild needs. Vertex's replacement gaskets and seals are available as top-end kits, complete engine kits, or as an oil seal kit.

• These sets include the head, base, and exhaust gaskets, valve seals, O-rings and other gaskets to complete a top-end rebuild.

Rough riding calls for stronger axles and that’s where All Balls Racing excels. Machined for exact OEM fit, the shaft is made of chromoly steel with a larger diameter than most axles. The axle has 6 ball bearings in each CV joint. Laminate coating resists corrosion and rust, and protects axle from dirt, water, rocks and grease. Waterproof neoprene boots act as a first line of defense, shielding vulnerable joints and preventing leaks. High performance molybdenum grease reduces heat and friction.

• In static torsion trials, these axles were up to 30% stronger than OEM and aftermarket competition.
• Lasts approximately 50 percent longer than many aftermarket competitors.
• Typically runs almost 130,000 cycles versus 80,000 cycles for many axles.

Features:

• 40% stronger than OEM.
• Larger 4340 chrome-moly steel axle bar.
• Precision ground components.
• Low profile clamps.
• Neoprene boots.
• Engineered in the USA.
• Manufactured in an ISO facility.
• Assembled with 3% molybdenum grease.

Features a black PVC outer jacket for maximum flexibility and durability, steel inner casing that is tightly coiled for low compression, pre-lubricated nylon inner sleeve, bird-caged wire ends, EPDM moulded rubber for high UV resistance and injection moulded components manufactured from high-strength POM material.

Features:

• Flexible and durable with steel inner casing that is tightly coiled for low compression.
• Pre-lubricated nylon inner sleeve.
• Bird caged wire ends.
• EPDM moulded rubber for high UV resistance and injection moulded components made from high-strength POM material.

Note: Kit contents may vary by fitment and are subject to change.

All Balls now offers a complete fork bush kit solution. The kit includes the following products:

• 2x slider bushings
• 2x leg bushings
• All copper washers and O-rings, 2 fork seal snap rings.

Quality design and construction of every All Balls piece meets the toughest standards and conditions — from daily commuting to full-on racing, all older bearing and seal designs are upgraded to the best and latest specs and designs.

Fuel pump strainers act as a first line of defence against fuel system contamination. Strainers filter out common contaminants found in gasoline such as dirt, dust and other particulate matter, as well as gasoline varnish. Quantum fuel pump strainers feature multiple layers of strainer media to filter progressively smaller particle sizes. The expanded surface area provides enhanced filtration, extending the life of the fuel pump.

Restricted fuel flow through a clogged strainer causes the fuel pump to work harder, reducing pump longevity. Strainer clogging is among the top causes of fuel pump failure making it important to replace your strainer regularly - before problems arise. We recommend replacing fuel pump strainers in powersports applications once a year as part of a preventative maintenance plan.

Features:

• Designed with gradient density to meet or exceed OE specifications.
• Designed to ensure optimal filtration to prevent fuel system contamination.
• Strainer material tested and validated for capacity and efficiency by accredited third party.

PH SERIES – Street Sport Sintered

High-performance HH friction rated sintered metal pads made in the USA to an exclusive Premier formulation. PH brake pads offer maximum durability and unbeatable performance under heavy braking and high-speed use. PH series is no longer available for off-road applications following the formulation improvements of the PR range for Moto-X and ATV applications.

All Balls now offers a complete fork bush kit solution. The kit includes the following products:

• 2x slider bushings
• 2x leg bushings
• All copper washers and O-rings, 2 fork seal snap rings.

Quality design and construction of every All Balls piece meets the toughest standards and conditions — from daily commuting to full-on racing, all older bearing and seal designs are upgraded to the best and latest specs and designs.

RMSTATOR is specialized in designing and manufacturing innovative electrical and electronic components for Powersports vehicles like motorcycles, ATV, SxS, UTV, snowmobiles, and PWC. Through unrelenting quality control, we ensure that each component meets or exceeds the OEM specs. With over 25 product families, rest assured that you will find the part you need.

STOP BURNING YOUR REGULATOR RECTIFIER! It is time to update or replace your voltage regulator with RM STATORS advanced MOSFET technology. RM STATORS MOSFET Regulators run cooler than all OEM diode style regulators. In addition, this rectifier has overheat protection, rather than burn up it will simply turn off for a while and cool off.

• Direct replacement to your original unit
• Plug-and-play, direct fit, easy installation
• The quality exceeds the OEM equipment
• Improved heat sink and charging capabilities
• Higher grade of electric components

What are the advantages of the MOSFET Technology?

• Runs much cooler than the traditional Shunt voltage regulator rectifier
• Less load on the stator, less work, less fuel is used and you save
• The power charging your battery is steadier and smooth
• Extends the battery’s life and cold-cranking capacity
• Removes stator load resulting in more engine power
• Optimize power delivery by switching the stator coils on or off

NOTE: Battery condition is extremely important. No voltage regulator can work correctly with a bad or weak battery. Always fully charge your battery before performing any charging system tests or replacing parts. If there is any doubt, have the battery load tested or replaced.

Please Note:

1. All electrical components must be fitted by a qualified technician.
2. Before fitting electrical components ensure the root cause of the original failure has been addressed.
3. The absence of either of points 1 or 2 above, will void any warranty.

P SERIES - Street Bikes

Premier's most successful general use material, our P series pads, are a tough Kevlar based organic material giving superb brake effect on all sportbikes and cruisers. This material is preselected by the catalogue when you order P prefix disc pads.

P SERIES - Off-Road

Part numbers relating to off-road machines are supplied in carbon graphite compound for medium durability, good brake effect and minimum heat generation.

Replacement ignition key switch for your motorcycle/ATV. Direct replacement to the original unit this unit provides excellent plug-and-play, direct fit functionality providing simple, quick & easy installation. Two keys & all connectors are included.

• Direct replacement to your original unit
• Plug-and-play, direct fit, easy installation.
• Two keys included
• Connector included

Dimensions:

• Height : 56mm
• Length: 41mm
• Wire Length: 270mm

Other Specification:

• Number of wires: 6
• Number of plugs: 1
• Number of keys: 2
• Number of positions: 3 (Off/On/Spring Return Start)

Carburetor repair kits

• Kits include all of the necessary components to repair a carburetor. ATV models with two carburetors include components to repair two carburetors.
• Kit includes necessary all O-rings, gaskets, jets, needle, mixture screw, float bowl screws, float valve needle and seat. (Needle jet and other pressed in jets are not included in kit.)
• OEM jet sizes are included in the kit. NBR rubber material is used on all O-rings and rubber gaskets NBR has excellent resistance to the ethanol used in today’s fuels.
• Applications that use paper float bowl gaskets are upgraded to High Performance Interface Gasket material.
• Components included in the kits are based off of US models and discretion must be used when attempting to install the kit on a non US model.
• Off road use only.

RMSTATOR is specialized in designing and manufacturing innovative electrical and electronic components for Powersports vehicles like motorcycles, ATV, SxS, UTV, snowmobiles, and PWC. Through unrelenting quality control, we ensure that each component meets or exceeds the OEM specs. With over 25 product families, rest assured that you will find the part you need.

• Direct replacement to your original unit
• Plug-and-play, direct fit, easy installation
• Highest grade of lamination materials
• Highest grade of copper winding, resistant to 200 degrees Celsius
• Connector included

Battery condition is extremely important. No stator can work correctly with a bad or weak battery. Always fully charge your battery before performing any charging system tests or replacing parts. If there is any doubt, have the battery load tested or replaced.

Dimensions:

• Interior diameter: 42 mm
• Exterior diameter: 115 mm
• Width: 21 mm

Other specifications:

• Number of wires: 3
• Number of plugs: 1
• Number of terminals: 3
• Harness length Stator to grommet: 80 mm
• Harness length grommet to plug: 650 mm

Wire to wire resistance:

• Alternator: Between each Black = 0.5 ohms +/- 20%

Please Note:

1. All electrical components must be fitted by a qualified technician.
2. Before fitting electrical components ensure the root cause of the original failure has been addressed.
3. The absence of either of points 1 or 2 above, will void any warranty.
4. There are 2 possibles stators for Triumph Daytona 955i 2002-2006, our product RM01388S fits on serial number #179431 and below. The other possible Stator is RM01395.

K&N XStream Series Motocross Air Filters take performance to the next level with the addition of a filter within the filter's top in order to add even more filtration area for high air-flow and capacity. Each filter piece has pleated media, which creates a large surface area that provides high airflow and great dirt holding capacity for extreme conditions. The two-piece design eases installation and removal on modern narrow-framed MX bikes. The epoxy-coated aluminium wire mesh, incorporated into a backfire screen, protects the filter element from harmful debris. A custom base seal ensures a precise and secure fit. K&N air filters are washable and reusable and they come pre-oiled and ready to use!

Features:

• Large surface area for long service life.
• Low restriction.
• Washable and reusable.
• Outstanding filtration.

Specifications:

• Height 2.688in (68mm)
• Washable: Yes
• Filter Material: Cotton Gauze
• Replacement Filter: E-3042

Quality carburettor rebuild kit from All Balls.

• Kits include all of the necessary components to repair a carburettor. ATV models with two carburettors include components to repair two carburettors.
• Kit includes necessary all O-rings, gaskets, jets, needle, mixture screw, float bowl screws, float valve needles and seat. (Needle jet and other pressed-in jets are not included in the kit.)
• OEM jet sizes are included in the kit. NBR rubber material is used on all O-rings and rubber gaskets NBR has excellent resistance to the ethanol used in today’s fuels.
• Applications that use paper float bowl gaskets are upgraded to High-Performance Interface Gasket material.
• Components included in the kits are based on US models and discretion must be used when attempting to install the kit on a non-US model.
• Off-road use only.

Wossner

For more than 35 years, Wössner successfully design and produce high-performance pistons and connecting rods.

In order to offer their customers the best of Wössner Power, their products are produced by using state-of-the-art technology and are subject to continuous quality control.

Performance, quality and longevity - this is what Wössner stands for with high-quality products.

Con Rod Kits

The Wössner 2-stroke connecting rods are always supplied with lifting pins, needle bearings, connecting rod bearings and spacers.
The Wössner 4-stroke connecting rods include crank pins and connecting rod bearings.
Please use our Fitments Tool to ensure the correct part is ordered.

Koubalink recommends a 20% increase in the proper spring rate for the rider due to the change in the leverage ratio.

KoubaLink specialises in motorcycle lowering and performance linkages for off-road and dual-sport rear suspension systems. Compromise is not an option at KoubaLink. Listening to riders from all over the world explain where and how they use their off-road and dual-sport bikes. With their input, Koubalink manufacture products that add to your motorcycling experience and make it a little more enjoyable.

• Provides better front-end stability by lowering rear suspension geometry
• Machined from billet aluminium
• Stronger than OEM
• Pre-installed OE style bearings included
• Replace linkage like its OEM
• Includes all required bearings and seals for assembly (Excluding Dog Bone styled linkages that do not include bearings and seals from factory)

All the bearings and seal required to refit a wheel in one convenient package.

Features:

• Premium high-speed bearings feature low drag.
• Double lip seals on both sides to provide superior exclusion of water and dirt
• Improved grease retention.

NOTE: This complete Vertex Gasket Set contains all parts as pictured.

Produced in the U.S.A. with the latest materials and technology in gasket production to Vertex specifications. Vertex gaskets ensure long-lasting performance and leak prevention for your rebuild needs. Vertex's replacement gaskets and seals are available as top-end kits, complete engine kits, or as an oil seal kit.

• One kit containing all of the gaskets, O-rings, and valve seals necessary to rebuild the entire engine and transmission.
• Includes transmission seals.

Hot Rods Transmission Bearing Kit replaces the often-overlooked transmission bearings with new components that restore original performance. The kit includes bearings for the primary shaft, secondary shaft and shift drum shafts. Replacing these bearings is highly recommended when rebuilding the transmission.

Features:

• Includes bearings for the primary shaft, secondary shaft, and shift drum shafts
• Replace the often-overlooked transmission bearings
• Perfect addition to a complete rebuild

OEM spacers typically wear out within a year of hard riding. The wheel spacers should be checked and replaced as needed with every bearing service. Water and dirt act as a grinding compound between the seal face and the mating surface of the spacer. Once the grooves are deep enough, the sealing surface is lost, allowing water and dirt to pass through and contaminate the bearing.

Wheel Spacer Kits are designed to restore the proper sealing surface between the wheel seal and spacer, helping protect wheel bearings from premature wear and failure. Manufactured to precise tolerances for a direct replacement fit, All Balls spacers provide a smooth, durable surface for the seal to run against, reducing the risk of contamination and extending bearing life. Ideal for routine maintenance or during wheel bearing replacement, a quality wheel spacer kit ensures reliable wheel performance in harsh riding conditions.

PR SERIES – Off-Road Sintered

Premier PR pads have been upgraded to a new HIGH DENSITY sintered metal compound suitable for all types of moto-x and ATV use.

NOTE: This Vertex Top End Gasket Set contains all components pictured.

Produced in the U.S.A. with the latest materials and technology in gasket production to Vertex specifications. Vertex gaskets ensure long-lasting performance and leak prevention for your rebuild needs. Vertex's replacement gaskets and seals are available as top-end kits, complete engine kits, or as an oil seal kit.

• These sets include the head, base, and exhaust gaskets, valve seals, O-rings and other gaskets to complete a top-end rebuild.

Each pack of Premier CSK Clutch Springs contains a complete set of heavy-duty springs. Up to 15% stronger than the original.

Customer should be advised that after installation of a CSK kit the clutch lever will feel slightly ‘heavier’ than standard

If you have a broken tie rod or just want some extra protection against breakage, take the opportunity to beef up the tie rods on your ATV with the All Balls Tie Rod Upgrade Kit.

The tie rods and ends included with this kit have improved resistance against bending and breaking, thanks to thicker 12mm ends compared to the 10mm stock ends. The kit gets even better when you consider the entire kit from All Balls retails for less than the cost of replacing 4 OEM tie rod ends.

This kit comes with 2 tie rods, 4 tie rod ends, and all the parts you’ll need to replace your old tie rods with the upgraded parts in the Tie Rod Upgrade Kit from All Balls.

Features:

• Upgrade 10mm tie rod ends to heavy-duty 12mm ends.
• Kit includes parts for conversion, 2 tie rods, and 4 rod ends.
• Retails for less than the cost of replacing 4 OEM 10mm tie rod ends.

GOLDfren began manufacturing sintered disc brake pads for a wide range of off-road and road motorcycles in 1991, nearly three decades on from their first motorcycle brake pads GOLDfren has become one of the largest aftermarket manufacturers in the motorcycle brake disc pad industry. Their development of next-generation products has kept them at the technological forefront of Sintered Friction Braking providing you with confidence in the performance, durability and reliability of your brakes.

K5 Series:

The K5 sintered compound is optimal for off-road motorcycles and ATVs. It is recommended for riders who demand great off-road stopping power and brake pad durability when riding on tough off-road terrains. The K5 series is designed for low abrasive interaction with the rotor, long life and self-cleaning capabilities necessary in off-road riding conditions. Friction materials contain metal-ceramic with a sophisticated bronze-graphite and full-metal mixture formulation with fine friction particles to achieve optimal friction properties.

Features:

• High static friction coefficient
• Good abrasive resistance
• Self-cleaning capability
• Low abrasive interaction with the brake rotor material
• Up to 3 times longer operational life compared to organic and Kevlar composite materials

Application:

• Developed specifically for off-road motorcycles & ATVs
• Can be used on both front and rear brakes
• Could be used on the rear brake of road racing motorcycles

Operating Parameters:

• Specific pressure: 2.0 Mpa
• Sliding velocity: 20 m/s
• Constant maximum temp: 500°C
• Short time maximum temp: 750°C
• Counter-surfaces: steel disks

What is a sintered brake pad?

GOLDfren only manufacturers sintered brake pads that contain metal-ceramic and ceramic-carbon friction materials, these materials allow for less brake dust and a quieter braking experience. Sintered brake pads are made by fusing together metallic particles under high temperature and pressure which enhances friction properties and pad life, resulting in longer life and stronger braking. Sintered brake pads experience no brake fade when operating at high temperatures and in wet conditions. They also last up to 5 times longer than organic pads and provide additional braking strength. All materials used are environmentally friendly and do not contain any lead, asbestos, fibreglass or formaldehyde.

Reminder: one set of brake pads services one brake disc, if you are servicing multiple discs you will need multiple sets of brake pads.

RMSTATOR is specialized in designing and manufacturing innovative electrical and electronic components for Powersports vehicles like motorcycles, ATV, SxS, UTV, snowmobiles, and PWC. Through unrelenting quality control, we ensure that each component meets or exceeds the OEM specs. With over 25 product families, rest assured that you will find the part you need.

• Direct replacement to your original unit
• Plug-and-play, direct fit, easy installation
• Two keys included
• All products shipped are tested

Dimensions:

• Height: 51mm
• Length: 39mm
• Width: 39mm

Other Specifications:

• Number of wires: 4
• Number of plugs: 1
• Number of keys: 2
• Number of positions: 2 (off, on)

Vertex Complete Engine Rebuild Kits are a simple and cost-effective way to complete a top-to-bottom professional rebuild for your 2 or 4-stroke motorcycle or ATV/UTV. The one easy to order kit will not only save you time by offering a one-stop-shop in a box, but they also save you money when compared to purchasing all items individually.

Vertex kits include quality components from Vertex, Hot Rods and Hot Cams.*

All parts are manufactured in the USA using the highest quality material.

Features:

• Crafted to deliver unbeatable levels of quality.
• High-grade materials for exceptional performance.
• Superior in durability and reliability.
• Kits available for many 2 and 4-stroke motorcycles, ATVs and UTVs.
• Cost-effective solution.
• Saves time sourcing individual components.
• Vertex pistons and gaskets.*
• Hot Rods crank and bearing kits.*
• Hot Cams cam chain.*

*Specific parts vary by kit (see included parts above).