HARD PARTS

Replacing the fuel tank seal or gasket is a vital part of the fuel pump replacement process. Quantum tank seals are made exclusively from Viton, which are impervious to ethanol and other chemicals that degrade conventional rubber over time. These OE replacements are designed for fitment on specific vehicles.

• Direct OEM replacement at a fraction of the cost
• Includes valve, hose, gaskets, screws, clamps and everything needed to replace the OEM petcock
• Viton rubber fuel resistant gaskets
• Includes OE style fuel line and clamps

All the bearings and seal required to refit a wheel in one convenient package.

Features:

• Premium high-speed bearings feature low drag.
• Double lip seals on both sides to provide superior exclusion of water and dirt
• Improved grease retention.

Crafted from military-spec certified TI3Al titanium alloy, Vertex Titanium Valves are made to endure the harshest racing conditions. Forged from a single blank, grain flow is improved to enhance the mechanical characteristics of the valve without having to resort to welding. Special PVD, CVD, and CrN coatings are used to provide low-friction surfaces that reduce heat generation and resist carbon build-up; coatings allow alloys like titanium to become ultra-smooth while reaching hardness levels 5x that of high-speed steel.

• Military-spec certified TI3Al titanium alloy
• Forged from a single blank
• PVD, CVD, and CrN coatings
• Reduces heat generation
• Resists carbon build-up
• Significantly stronger than steel

NOTE: This Vertex Top End Gasket Set contains all components pictured.

Produced in the U.S.A. with the latest materials and technology in gasket production to Vertex specifications. Vertex gaskets ensure long-lasting performance and leak prevention for your rebuild needs. Vertex's replacement gaskets and seals are available as top-end kits, complete engine kits, or as an oil seal kit.

• These sets include the head, base, and exhaust gaskets, valve seals, O-rings and other gaskets to complete a top-end rebuild.

Rough riding calls for stronger axles and that’s where All Balls Racing excels. Machined for exact OEM fit, the shaft is made of chromoly steel with a larger diameter than most axles. The axle has 6 ball bearings in each CV joint. Laminate coating resists corrosion and rust and protects axles from dirt, water, rocks and grease. Waterproof neoprene boots act as a first line of defence, shielding vulnerable joints and preventing leaks. High-performance molybdenum grease reduces heat and friction.

In static torsion trials, these axles were up to 30% stronger than OEM and aftermarket competition.

Features:

• 40% stronger than OEM.
• Larger 4340 chrome-moly steel axle bar.
• Precision ground components.
• Low profile clamps.
• Lasts approximately 50 percent longer than many aftermarket competitors.
• Neoprene boots.
• Typically runs almost 130,000 cycles versus 80,000 cycles for many axles.
• Engineered in the USA.
• Manufactured in an ISO facility.Assembled with 3% molybdenum grease.

All the bearings and seal required to refit a wheel in one convenient package.

Features:

• Premium high-speed bearings feature low drag.
• Double lip seals on both sides to provide superior exclusion of water and dirt
• Improved grease retention.

Quality king pin kit from All Balls Racing. Features steel bushings, needle- bearing shaft and seals. Great value.

K&N's high-flow air filters are available as a replacement for your stock motorcycle air filter element. They are custom-engineered to fit your specific application and are designed to provide low restriction and increased performance while providing excellent engine protection for your motorcycle.

Features:

• Designed to provide increased horsepower and torque.
• Pleated media provides a large filtration area, offering long service intervals.
• Multiple layers of woven cotton gauze media offer excellent filtration.
• Application-specific base seal and sealing bead.
• Made in the USA for over 40 years.
• Washable and reusable, pre-oiled and ready to ride!

Specifications

• Height : 0.875in (22mm)
• Washable: Yes
• Filter Material: Cotton Gauze
• Outside Length: 13in (330mm)
• Outside Width: 6.688in (170mm)
• Filter Re-Oiling Amount: 0.63oz (19ml)

All Balls now offers a complete fork bush kit solution. The kit includes the following products:

• 2x slider bushings
• 2x leg bushings
• All copper washers and O-rings, 2 fork seal snap rings.

Quality design and construction of every All Balls piece meets the toughest standards and conditions — from daily commuting to full-on racing, all older bearing and seal designs are upgraded to the best and latest specs and designs.

K&N's high-flow air filters are available as a replacement for your stock motorcycle air filter element. They are custom-engineered to fit your specific application and are designed to provide low restriction and increased performance, while providing excellent engine protection for your motorcycle.

Features:

• Designed to provide increased horsepower and torque.
• Pleated media provides a large filtration area, offering long service intervals.
• Multiple layers of woven cotton gauze media offer excellent filtration.
• Application-specific base seal and sealing bead.
• Made in the USA for over 40 years.
• Washable and reusable, pre-oiled and ready to ride!

Specifications:

• Filter Material: Cotton Gauze
• Height: 2.25in (57mm)
• Inside Diameter: 4.75in (121mm)
• Outside Diameter: 6in (152mm)
• Washable: Yes
• Filter Re-Oiling Amount: 0.39oz (12ml)

A quality Steering Head Bearing kit from All Balls. Make your bike handle like new!

Features:

• Upgrade ball-type steering bearings to Heavy-Duty Tapered Bearings
• Higher torque load and better wear than OEM ball-style steering bearings.
• Each kit is complete with upper and lower bearing sets and seals.

Wossner

For more than 35 years, Wössner successfully design and produce high-performance pistons and connecting rods.

In order to offer their customers the best of Wössner Power, their products are produced by using state-of-the-art technology and are subject to continuous quality control.

Performance, quality and longevity - this is what Wössner stands for with high-quality products.

Con Rod Kits

The Wössner 2-stroke connecting rods are always supplied with lifting pins, needle bearings, connecting rod bearings and spacers.
The Wössner 4-stroke connecting rods include crank pins and connecting rod bearings.
Please use our Fitments Tool to ensure the correct part is ordered.

• Direct OEM replacement fuel line clamp kit
• This ultimate fuel line clamp kit is an absolute necessity for any shop, technician, or DIY mechanic
• Kit contains 4 of each Fuel Star fuel line OEM replica clamps, available in sizes from 7-17mm I.D.
• Each clamp is an exact replica of the major OEM's fuel line clamps and is manufactured to meet or exceed OEM performance, aesthetics, and fit
• 4-packs also available to refill the kit

NOTE: This complete Vertex Gasket Set contains all parts as pictured.

Produced in the U.S.A. with the latest materials and technology in gasket production to Vertex specifications. Vertex gaskets ensure long-lasting performance and leak prevention for your rebuild needs. Vertex's replacement gaskets and seals are available as top-end kits, complete engine kits, or as an oil seal kit.

• One kit containing all of the gaskets, O-rings, and valve seals necessary to rebuild the entire engine and transmission.
• Includes transmission seals.

• Direct OEM replacement at a fraction of the cost
• Includes valve, hose, gaskets, screws, clamps and everything needed to replace the OEM petcock
• Viton rubber fuel resistant gaskets
• Includes OE style fuel line and clamps

Brand new aftermarket Voltage Regulator Rectifier

• Direct replacement to your original unit
• Plug-and-play, direct fit, easy installation
• No assembly required
• Higher grade of electric components
• The quality exceeds the OEM equipment
• All products shipped are tested

We have even included the opposite connector (main harness side) as we know these are often melted / corroded / defective and are a major cause of repetitive electrical issues.

All item pictures are accurate, if in doubt, do not hesitate and compare our item to your original part.

Specifications:

Dimensions:

• W idth: 52 mm
• Length: 72 mm
• Height: 20 mm
• Wires length: 480 mm
• Distance between fixation holes center to center: 60 mm

Other specifications:

• Number of plugs: 2
• Number of pins: 4
• Number of wires: 4
• Minimum Charging Voltage: 14.5 V +- 0.5 V
• Maximum Charging Current: 50 A / 500 W
• Open Circuit Voltage: < 15 V
• Operation Temperature: -20°C to 85°C

Note: Battery condition is important. No regulator can make up for a bad or weak battery. If in doubt charge your battery and have it load tested, or simply replace it. ALWAYS START WITH A FULLY CHARGED BATTERY

4-pack of replacement Fuel Star fuel line clamps for the All Balls Complete OEM Style Fuel Line Clamp Kit.

• Inside Diameter: 15.2mm
• Clamp Style: Wire
• Quantity: 4

A quality caliper rebuild kit from All Balls. Contains everything needed to rebuild your caliper to like new condition.

GOLDfren began manufacturing sintered disc brake pads for a wide range of off-road and road motorcycles in 1991, nearly three decades on from their first motorcycle brake pads GOLDfren has become one of the largest aftermarket manufacturers in the motorcycle brake disc pad industry. Their development of next-generation products has kept them at the technological forefront of Sintered Friction Braking providing you with confidence in the performance, durability and reliability of your brakes.

K5 Series:

The K5 sintered compound is optimal for off-road motorcycles and ATVs. It is recommended for riders who demand great off-road stopping power and brake pad durability when riding on tough off-road terrains. The K5 series is designed for low abrasive interaction with the rotor, long life and self-cleaning capabilities necessary in off-road riding conditions. Friction materials contain metal-ceramic with a sophisticated bronze-graphite and full-metal mixture formulation with fine friction particles to achieve optimal friction properties.

Features:

• High static friction coefficient
• Good abrasive resistance
• Self-cleaning capability
• Low abrasive interaction with the brake rotor material
• Up to 3 times longer operational life compared to organic and Kevlar composite materials

Application:

• Developed specifically for off-road motorcycles & ATVs
• Can be used on both front and rear brakes
• Could be used on the rear brake of road racing motorcycles

Operating Parameters:

• Specific pressure: 2.0 Mpa
• Sliding velocity: 20 m/s
• Constant maximum temp: 500°C
• Short time maximum temp: 750°C
• Counter-surfaces: steel disks

What is a sintered brake pad?

GOLDfren only manufacturers sintered brake pads that contain metal-ceramic and ceramic-carbon friction materials, these materials allow for less brake dust and a quieter braking experience. Sintered brake pads are made by fusing together metallic particles under high temperature and pressure which enhances friction properties and pad life, resulting in longer life and stronger braking. Sintered brake pads experience no brake fade when operating at high temperatures and in wet conditions. They also last up to 5 times longer than organic pads and provide additional braking strength. All materials used are environmentally friendly and do not contain any lead, asbestos, fibreglass or formaldehyde.

Reminder: one set of brake pads services one brake disc, if you are servicing multiple discs you will need multiple sets of brake pads.

PR SERIES – Off-Road Sintered

Premier PR pads have been upgraded to a new HIGH DENSITY sintered metal compound suitable for all types of moto-x and ATV use.

All Balls OEM replacement air filters are manufactured to meet or exceed OEM specifications. Constructed to fit the factory air box and are direct replacements to OEM air filters. The premium filtering media prevents dirt and dust from entering your engine while maintaining excellent airflow.

• OEM replacement air filter
• Meets or exceeds OEM specifications
• Fits factory air box
• Excellent airflow
• Premium filtration

Includes components necessary to complete a piston (top end) rebuild. Competitive pricing, made to meet and exceed OEM quality and designed as a direct OEM replacement.

Features:

• Designed for OEM replacement.
• Made from high-quality materials.
• Meet or exceed OEM specifications.
• Competitive pricing.

Air Cut Off Valve Rebuild Kits

Poor running conditions or popping on deceleration are signs that you may need to rebuild the air cut off valve.

All of the necessary parts to rebuild the air cut off valve circuit are included. Kits for vehicles with multiple carburetors include all components for all carburetors.

RMSTATOR is specialized in designing and manufacturing innovative electrical and electronic components for Powersports vehicles like motorcycles, ATV, SxS, UTV, snowmobiles, and PWC. Through unrelenting quality control, we ensure that each component meets or exceeds the OEM specs. With over 25 product families, rest assured that you will find the part you need.

• Direct replacement to your original unit
• Plug-and-play, direct fit, easy installation
• Highest grade of lamination materials
• Highest grade of copper winding, resistant to 200 degrees Celsius
• Connector included

Battery condition is extremely important. No stator can work correctly with a bad or weak battery. Always fully charge your battery before performing any charging system tests or replacing parts. If there is any doubt, have the battery load tested or replaced.

Please Note:

1. All electrical components must be fitted by a qualified technician.
2. Before fitting electrical components ensure the root cause of the original failure has been addressed.
3. The absence of either of points 1 or 2 above, will void any warranty.