HARD PARTS

The All Balls CV Boot material is compounded from an OEM grade DCR66 rubber that is formulated specifically for the demanding requirements of today’s ATVs and UTVs.

• 40% higher tensile strength than conventional CV boo material, suitable for the high joint angles of modern ATVs and UTVs.
• 50% more abrasion-resistant than conventional CV boot material to ensure a long life in harsh off-road environments.
• Rubber compound is tested to -40° F to ensure good performance and long life at low temperatures.
• Lithium-based Molybdenum Grease insures good lubrication for long CV joint life. Easier to install than most OEM and aftermarket boots. Sold each. Does not require the use of a ""Banding Tool"".

Specifications:

• H: 86mm
• SD: 17mm
• LD: 59mm
• Shaft I.D.: 17
• CV Body I.D.: 59
• Length: 86

Kits include:

• Two stainless steel clamps that are designed to be tightened without the use of special tools.

A quality caliper rebuild kit from All Balls. Contains everything needed to rebuild your caliper to like new condition.

Produced in the U.S.A. with the latest materials and technology in gasket production to Vertex specifications. Vertex gaskets ensure long-lasting performance and leak prevention for your rebuild needs. Vertex's replacement gaskets and seals are available as top-end kits, complete engine kits, or as an oil seal kit.

• One kit containing all of the gaskets necessary to rebuild the water pump.
• Designed to fit O.E.M. water pump.

• Direct OEM replacement at a fraction of the cost
• Includes valve, hose, gaskets, screws, clamps and everything needed to replace the OEM petcock
• Viton rubber fuel resistant gaskets
• Includes OE style fuel line and clamps

A quality master cylinder repair kit from All Balls. Contains everything needed to repair your master cylinder to like new condition. 

All Balls Master Cylinder Rebuild Kits are made from Premuim products and include everything to rebuild your leaky Master Cylinder.  

Each pack of Premier CSK Clutch Springs contains a complete set of heavy-duty springs. Up to 15% stronger than the original.

Customer should be advised that after installation of a CSK kit the clutch lever will feel slightly ‘heavier’ than standard

NOTE: This Vertex Top End Gasket Set contains all components pictured.

Produced in the U.S.A. with the latest materials and technology in gasket production to Vertex specifications. Vertex gaskets ensure long-lasting performance and leak prevention for your rebuild needs. Vertex's replacement gaskets and seals are available as top-end kits, complete engine kits, or as an oil seal kit.

• These sets include the head, base, and exhaust gaskets, valve seals, O-rings and other gaskets to complete a top-end rebuild.

NOTE: This Vertex Top End Gasket Set contains all components pictured.

Produced in the U.S.A. with the latest materials and technology in gasket production to Vertex specifications. Vertex gaskets ensure long-lasting performance and leak prevention for your rebuild needs. Vertex's replacement gaskets and seals are available as top-end kits, complete engine kits, or as an oil seal kit.

• These sets include the head, base, and exhaust gaskets, valve seals, O-rings and other gaskets to complete a top-end rebuild.

RMSTATOR is specialized in designing and manufacturing innovative electrical and electronic components for Powersports vehicles like motorcycles, ATV, SxS, UTV, snowmobiles, and PWC. Through unrelenting quality control, we ensure that each component meets or exceeds the OEM specs. With over 25 product families, rest assured that you will find the part you need.

• Direct replacement to your original unit
• Plug-and-play, direct fit, easy installation
• Highest grade of lamination materials
• Highest grade of copper winding, resistant to 200 degrees Celsius
• Connector included
• Applications: RMSTATOR RANGER / CREW / GENERAL / ACE 900 1000 2013-2019

Battery condition is extremely important. No stator can work correctly with a bad or weak battery. Always fully charge your battery before performing any charging system tests or replacing parts. If there is any doubt, have the battery load tested or replaced.

Please Note:

1. All electrical components must be fitted by a qualified technician.
2. Before fitting electrical components ensure the root cause of the original failure has been addressed.
3. The absence of either of points 1 or 2 above, will void any warranty.

The HFP-182 is a low-pressure frame mounted electric fuel pump for 1999-2014 carburetted Polaris Ranger 400/ 500 ATV/ UTV's.  This pump is a direct replacement for Polaris part numbers 4011545, 4011492, 4010658, 4170020.

• OEM or better performance
• Polished corrosion-resistant case to help minimize seizing during non- operation
• Specifically designed for quiet operation
• Drop-in replacement
• Patented check valve technology
• Compatible with modern diesel and ethanol-infused pump gasoline

A low-pressure frame mounted electric fuel pump for 1999-2014 carburetted Polaris Ranger 400/ 500 ATV/ UTV's.  This pump is a direct replacement for Polaris part numbers 4011545, 4011492, 4010658, 4170020.

• OEM or better performance
• Polished corrosion-resistant case to help minimize seizing during non-operation
• Specifically designed for quiet operation
• Drop-in replacement
• Patented check valve technology
• Compatible with modern diesel and ethanol-infused pump gasoline

RMSTATOR is specialized in designing and manufacturing innovative electrical and electronic components for Powersports vehicles like motorcycles, ATV, SxS, UTV, snowmobiles, and PWC. Through unrelenting quality control, we ensure that each component meets or exceeds the OEM specs. With over 25 product families, rest assured that you will find the part you need.

• Direct replacement to your original unit
• Plug-and-play, direct fit, easy installation
• Highest grade of lamination materials
• Highest grade of copper winding, resistant to 200 degrees Celsius
• Connector included

Battery condition is extremely important. No stator can work correctly with a bad or weak battery. Always fully charge your battery before performing any charging system tests or replacing parts. If there is any doubt, have the battery load tested or replaced.

Please Note:

1. All electrical components must be fitted by a qualified technician.
2. Before fitting electrical components ensure the root cause of the original failure has been addressed.
3. The absence of either of points 1 or 2 above, will void any warranty.

Putoline Oil is a Dutch manufacturer and supplier of high-quality oils and lubricants developed specifically for motorcycles, scooters and quads, making Putoline unique. Almost 50 years of experience and continual research allows Putoline to provide cutting edge products. Manufacturing their own products guarantees consistently high-quality motorcycle oils. Putoline Oil, Driven by Technology!

Putoline air filters, based on leading-edge open-cell foam technology, bring users major benefits, including:

• Improved performance through increased airflow
• Improved protection through finer filtration levels
• Substantial cost savings through serviceability and re-use

Fully reticulated (open cell) foam, as used in all Putoline filter products, consists of a honeycomb of tiny, interlocking cells of uniform size.  When treated with specially formulated filter oil, each passageway is like hundreds of very small centrifugal/oil bath filters connected one to another.  In this way, the foam traps and holds the particles throughout the entire volume of foam.

The development of this unique foam represents a major advancement in air filtration technology. As a result, foam air filters, when compared with paper or cotton gauze equivalents, combine great airflow capability, huge dust holding capacity, and very high filtration efficiency for even extremely small particles.

Construction:

1. Coarse open-pore foam catches airborne dirt, grime and sand.
2. Fine open-pore inner foam acts as a second filter to trap the smallest particles while ensuring maximum air passage.
3. Exclusively formulated adhesive ensures glue seams will not break down.
4. Thick, flat foam, greaseless sealing ring ensures maximum contact with your airbox, while acting as a breathable gasket for increased air passage.
5. Fused outer and inner elements prevent dirt and grime from being lodged between layers. Trapped particles can restrict airflow. If dirt works it's way into your engine, a pinhead-sized granule will gouge your piston and rings like a bullet. 

4-pack of replacement Fuel Star fuel line clamps for the All Balls Complete OEM Style Fuel Line Clamp Kit.

• Inside Diameter: 11.5mm
• Clamp Style: Wire
• Quantity: 4

P SERIES - Street Bikes

Premier's most successful general use material, our P series pads, are a tough Kevlar based organic material giving superb brake effect on all sportbikes and cruisers. This material is preselected by the catalogue when you order P prefix disc pads.

P SERIES - Off-Road

Part numbers relating to off-road machines are supplied in carbon graphite compound for medium durability, good brake effect and minimum heat generation.

K&N's Universal Air Filters are designed and manufactured for a wide variety of applications, including racing vehicles, radio-controlled cars, generators, snowmobiles, tractors, and other applications. Regardless of the angle or offset diameter of the air intake, there is probably a K&N Universal air filter for your equipment. All filters are constructed with ultra-strong moulded pliable rubber flanges that absorb vibration and allow for secure attachment and can also be stretched for up to 1/16 of an inch (1.5mm) to fit in-between sizes. K&N universal air filters are washable and reusable.

Features:

• Designed to increase horsepower and acceleration.
• Hundreds of sizes and shapes for most applications.
• High air flow with excellent filtration.
• Clamp-on washable and reusable air filter.
• Malleable flanges.

Specifications:

• Ai r Filter Shape: Oval Tapered
• Height: 191 mm (7.5 in)
• Washable: Yes
• Air Filter Material: Cotton Gauze
• Flange Inside Width: 72 mm (2.844 in)
• Flange Inside Length: 122 mm (4.813 in)
• Flange Length: 21 mm (0.813 in)
• Flange Type: Centered
• Flanges: 1
• Base Outside Length: 165 mm (6.5 in)
• Base Outside Width: 121 mm (4.75 in)
• Top Outside Length: 114 mm (4.5 in)
• Top Outside Width: 83 mm (3.25 in)
• Top Style: Rubber
• Top Material: Rubber
• Weight: 0.6 kg (1.4 lb)
• Filter Re-Oiling Amount: 39 ml (1.33 oz)

If you have a broken tie rod or just want some extra protection against breakage, take the opportunity to beef up the tie rods on your ATV with the All Balls Tie Rod Upgrade Kit.

The tie rods and ends included with this kit have improved resistance against bending and breaking, thanks to thicker 12mm ends compared to the 10mm stock ends. The kit gets even better when you consider the entire kit from All Balls retails for less than the cost of replacing 4 OEM tie rod ends.

This kit comes with 2 tie rods, 4 tie rod ends, and all the parts you’ll need to replace your old tie rods with the upgraded parts in the Tie Rod Upgrade Kit from All Balls.

Features:

• Upgrade 10mm tie rod ends to heavy-duty 12mm ends.
• Kit includes parts for conversion, 2 tie rods, and 4 rod ends.
• Retails for less than the cost of replacing 4 OEM 10mm tie rod ends.

K&N's high-flow air filters are available as a replacement for your stock motorcycle air filter element. They are custom-engineered to fit your specific application and are designed to provide low restriction and increased performance, while providing excellent engine protection for your motorcycle.

Features:

• Designed to provide increased horsepower and torque.
• Pleated media provides a large filtration area, offering long service intervals.
• Multiple layers of woven cotton gauze media offer excellent filtration.
• Application-specific base seal and sealing bead.
• Made in the USA for over 40 years.
• Washable and reusable, pre-oiled and ready to ride!

Specifications:

• Heigh t: 2.063in (52mm)
• Washable: Yes
• Filter Material: Cotton Gauze
• Weight: 1.4 lb (0.6kg)
• Filter Re-Oiling Amount: 0.38oz (11ml)

A quality caliper rebuild kit from All Balls. Contains everything needed to rebuild your caliper to like new condition.

Crafted from military-spec certified TI3Al titanium alloy, Vertex Titanium Valves are made to endure the harshest racing conditions. Forged from a single blank, grain flow is improved to enhance the mechanical characteristics of the valve without having to resort to welding. Special PVD, CVD, and CrN coatings are used to provide low-friction surfaces that reduce heat generation and resist carbon build-up; coatings allow alloys like titanium to become ultra-smooth while reaching hardness levels 5x that of high-speed steel.

• Military-spec certified TI3Al titanium alloy
• Forged from a single blank
• PVD, CVD, and CrN coatings
• Reduces heat generation
• Resists carbon build-up
• Significantly stronger than steel

Set of engine components. Easy to install. thanks to the precision fit for four-stroke and two-stroke applications.

Includes a set of main bearings and seals that are made to exact OEM tolerances so you get components that are interchangeable with OEM and other Hot Rods parts. Your crankshaft will turn true for seasons of riding.

Features:

• Full set of main crankshaft bearings and seals.
• Meets or exceeds OEM specs.
• Can be used with OEM or Hot Rods components

These brake disks are made of 420 stainless steel, providing excellent corrosion resistance.

• Hardened to 36HRC for excellent braking performance and durability
• Precision ground surfaces
• Laser engraved with part number and minimum thickness specification

All Balls Fuel Pump Kits are designed to restore lost performance caused by a failing or non-functioning fuel pump. Each kit offers a plug-and-play solution for quick and easy replacement of your OEM fuel pump module.

Kit contents vary by application and may include components such as the pump, filter, hoses, clamps, and wiring harness. Some kits contain only core components like the pump and filter. Please refer to the product image and listing details for exact contents specific to your model.

Features:

• OEM replacement fuel pump kits.
• Plug-and-play installation.
• Contents vary by kit — check image and listing for details.

Wrench Rabbit Rebuild Kits have been rebranded to Vertex Rebuild Kits; all components remain unchanged however you may receive a kit that is boxed differently to the one pictured.

Vertex Complete Engine Rebuild Kits are a simple and cost-effective way to complete a top-to-bottom professional rebuild for your 2 or 4-stroke motorcycle or ATV/UTV. The one easy to order kit will not only save you time by offering a one-stop-shop in a box, but they also save you money when compared to purchasing all items individually.

Vertex kits include quality components from Vertex, Hot Rods & Hot Cams.*

All parts are manufactured in the USA from the highest quality material.

Features:

• Crafted to deliver unbeatable levels of quality
• High-grade materials for exceptional performance
• Superior in durability and reliability
• Kits available for many 2 & 4-stroke motorcycles, ATVs & UTVs
• Cost-effective solution
• Saves time sourcing individual components
• Vertex pistons & gaskets*
• Hot Rods crank & bearing kits*
• Hot Cams cam chain*

Includes:

• Crankshaft
• Piston Kit
• Complete Engine Gasket Kit
• Oil Seal Kit
• Main Bearing and Seal Kit
• Water Pump Rebuild Kit
• Transmission Bearing Kit
• Countershaft Bushing/Seal Kit
• Cam Chain

*Specific parts vary by kit (see included parts above).

RMSTATOR is specialized in designing and manufacturing innovative electrical and electronic components for Powersports vehicles like motorcycles, ATV, SxS, UTV, snowmobiles, and PWC. Through unrelenting quality control, we ensure that each component meets or exceeds the OEM specs. With over 25 product families, rest assured that you will find the part you need.

• Direct replacement to your original unit
• Plug-and-play, direct fit, easy installation
• Highest grade of lamination materials
• Highest grade of copper winding, resistant to 200 degrees Celsius
• Connector included

Battery condition is extremely important. No stator can work correctly with a bad or weak battery. Always fully charge your battery before performing any charging system tests or replacing parts. If there is any doubt, have the battery load tested or replaced.

Please Note:

1. All electrical components must be fitted by a qualified technician.
2. Before fitting electrical components ensure the root cause of the original failure has been addressed.
3. The absence of either of points 1 or 2 above, will void any warranty.

Upgrade your motorcycle's clutch system with the All Balls Racing Motorcycle Clutch Cable. Designed with precision and durability in mind, this clutch cable delivers exceptional performance and reliability on the road.

• Black PVC outer jacket for maximum flexibility and durability.
• Steel inner casing that is tightly coiled for low compression.
• A pre-lubricated nylon inner sleeve guarantees smooth operation and long life.
• All wire ends are bird-caged prior to terminal casting for superior pull-out resistance.
• EPDM-moulded rubber components for high UV resistance and long life.
• Injected moulded components are manufactured from high-strength POM material.

Features a black PVC outer jacket for maximum flexibility and durability, steel inner casing that is tightly coiled for low compression, pre-lubricated nylon inner sleeve, bird-caged wire ends, EPDM moulded rubber for high UV resistance and injection moulded components manufactured from high-strength POM material.

Features:

• Flexible and durable with steel inner casing that is tightly coiled for low compression.
• Pre-lubricated nylon inner sleeve.
• Bird caged wire ends.
• EPDM moulded rubber for high UV resistance and injection moulded components made from high-strength POM material.

Note: Kit contents may vary by fitment and are subject to change.

Features a black PVC outer jacket for maximum flexibility and durability, steel inner casing that is tightly coiled for low compression, pre-lubricated nylon inner sleeve, bird-caged wire ends, EPDM moulded rubber for high UV resistance and injection moulded components manufactured from high-strength POM material.

Features:

• Flexible and durable with steel inner casing that is tightly coiled for low compression.
• Pre-lubricated nylon inner sleeve.
• Bird caged wire ends.
• EPDM moulded rubber for high UV resistance and injection moulded components made from high-strength POM material.

Note: Kit contents may vary by fitment and are subject to change.

GOLDfren began manufacturing sintered disc brake pads for a wide range of off-road and road motorcycles in 1991, nearly three decades on from their first motorcycle brake pads GOLDfren has become one of the largest aftermarket manufacturers in the motorcycle brake disc pad industry. Their development of next-generation products has kept them at the technological forefront of Sintered Friction Braking providing you with confidence in the performance, durability and reliability of your brakes.

K5 Series:

The K5 sintered compound is optimal for off-road motorcycles and ATVs. It is recommended for riders who demand great off-road stopping power and brake pad durability when riding on tough off-road terrains. The K5 series is designed for low abrasive interaction with the rotor, long life and self-cleaning capabilities necessary in off-road riding conditions. Friction materials contain metal-ceramic with a sophisticated bronze-graphite and full-metal mixture formulation with fine friction particles to achieve optimal friction properties.

Features:

• High static friction coefficient
• Good abrasive resistance
• Self-cleaning capability
• Low abrasive interaction with the brake rotor material
• Up to 3 times longer operational life compared to organic and Kevlar composite materials

Application:

• Developed specifically for off-road motorcycles & ATVs
• Can be used on both front and rear brakes
• Could be used on the rear brake of road racing motorcycles

Operating Parameters:

• Specific pressure: 2.0 Mpa
• Sliding velocity: 20 m/s
• Constant maximum temp: 500°C
• Short time maximum temp: 750°C
• Counter-surfaces: steel disks

What is a sintered brake pad?

GOLDfren only manufacturers sintered brake pads that contain metal-ceramic and ceramic-carbon friction materials, these materials allow for less brake dust and a quieter braking experience. Sintered brake pads are made by fusing together metallic particles under high temperature and pressure which enhances friction properties and pad life, resulting in longer life and stronger braking. Sintered brake pads experience no brake fade when operating at high temperatures and in wet conditions. They also last up to 5 times longer than organic pads and provide additional braking strength. All materials used are environmentally friendly and do not contain any lead, asbestos, fibreglass or formaldehyde.

Reminder: one set of brake pads services one brake disc, if you are servicing multiple discs you will need multiple sets of brake pads.