HARD PARTS

Quality carburettor rebuild kit from All Balls.

• Kits include all of the necessary components to repair a carburettor. ATV models with two carburettors include components to repair two carburettors.
• Kit includes necessary all O-rings, gaskets, jets, needle, mixture screw, float bowl screws, float valve needles and seat. (Needle jet and other pressed-in jets are not included in the kit.)
• OEM jet sizes are included in the kit. NBR rubber material is used on all O-rings and rubber gaskets NBR has excellent resistance to the ethanol used in today’s fuels.
• Applications that use paper float bowl gaskets are upgraded to High-Performance Interface Gasket material.
• Components included in the kits are based on US models and discretion must be used when attempting to install the kit on a non-US model.
• Off-road use only.

• Direct OEM replacement at a fraction of the cost
• Includes valve, hose, gaskets, screws, clamps and everything needed to replace the OEM petcock
• Viton rubber fuel resistant gaskets
• Includes OE style fuel line and clamps

Wossner

For more than 35 years, Wössner successfully design and produce high- performance pistons and connecting rods.

In order to offer their customers the best of Wössner Power, their products are produced by using state-of-the-art technology and are subject to continuous quality control.

Performance, quality and longevity - this is what Wössner stands for with high-quality products.

Con Rod Kits

The Wössner 2-stroke connecting rods are always supplied with lifting pins, needle bearings, connecting rod bearings and spacers.
The Wössner 4-stroke connecting rods include crank pins and connecting rod bearings.
Please use our Fitments Tool to ensure the correct part is ordered.

The All Balls Upper Shock Bearing Kit is designed to replace worn-out shock bushings and bearings and give superior suspension compliance.

Features:

• Contains the bearing(s) and all of the seals, spacers and pins (if required) to rebuild your shock bearings to factory specifications.
• O.E.M.-style cup seal.
• Bearings made with hardened and precision-ground 52100 bearing steel.

Note: Kit contents will vary by fitment and are subject to change

Up to 40% stronger than OE axles, these complete axles feature enlarged CV joints, bearing cages, and chromoly axle shafts. All internal components are precision ground and utilize molybdenum grease.

Features:

• 40% stronger than OEM.
• Larger 4340 chrome-moly steel axle bar.
• Precision ground components.
• Low profile clamps.
• Neoprene boots.
• Engineered in the USA.
• Manufactured in an ISO facility.
• Assembled with 3% moly grease.
• Black oxide coating to resist rust and corrosion.

Wossner is Germany's finest aftermarket forged piston and rod manufacturer and have over 25 years of experience in the high-performance racing industry. Top European racers and FIM World Champions rely on Wossner for only the best pistons, rods and customer service.

Features:

• In-house designed and manufactured; all forgings are produced in Wossner's company-owned forging operation.
• 4-stroke pistons are made using a double-bridged forging design.
• Lightweight pistons with the tightest piston-wall clearances in the industry give you a quieter running engine.
• Wossner pistons are used by leading Supercross, Arenacross and MX GP teams.
• Made in Germany

Specifications:

• Pis ton Size: 96.97mm
• Oversize: Standard

NOTE: Wossner Piston Kits include the Piston, Wrist Pin, Circlips and Rings, Needle Bearings are not included.

For over 40 years K&N has been designing and manufacturing performance air filters for the motorcycle and ATV enthusiast interested in maximizing horsepower and acceleration. Our air filter is designed to achieve high, virtually unrestricted air flow while maintaining filtration levels critical to ensure long engine life. K&N Air Filters will NOT void Motorcycle Warranty and are environmentally friendly. K&N Reusable Air Filters reduce the volume of disposable air filters that end up in landfills!

• Designed to provide increased Horsepower and Acceleration
• Pleated cotton media provides a large filtration area offering low restriction and long service intervals
• Multi-Layers of woven cotton gauze media offers excellent filtration
• Fits directly into OEM Airbox with application specific Sealing Bead ensuring a precise fit
• No fuel Management modifications are normally required to obtain increased performance
• Washable & reusable, most are pre-oiled and ready to ride!

In the early 1960s, two motorcycle racers, Ken Johnson and Norm McDonald (K&N) developed a ground-breaking new idea for an air filter. After experimenting with numerous types of filter media, they discovered that an oiled cotton design allowed the filter to not only capture contaminants very efficiently, but also allowed it to be washed and reused, and the original K&N High-Flow Air Filter was born. Five decades later, K&N is still innovating industry-leading filtration technology. In addition to performance air filters, K&N® now manufactures a variety of other protection and performance products, including air intake systems, oil filters & fuel filters, with a reputation for exceptional quality and customer service.

K&N's high-flow air filters are available as a replacement for your stock motorcycle air filter element. They are custom engineered to fit your specific application and are designed to provide low restriction and increased performance, while providing excellent engine protection for your motorcycle.

Features

• Designed to provide increased horsepower and torque
• Pleated media provides a large filtration area offering long service intervals
• Multiple layers of woven cotton gauze media offer excellent filtration
• Application-specific base seal and sealing bead
• Made in the USA for over 40 years
• Washable & reusable, pre-oiled and ready to ride!

Specifications

• Height: 3in (76mm)
• Washable: Yes
• Filter Material: Cotton Gauze
• Filter Re-Oiling Amount: 0.83oz (25ml)

K&N's high-flow air filters are available as a replacement for your stock motorcycle air filter element. They are custom-engineered to fit your specific application and are designed to provide low restriction and increased performance, while providing excellent engine protection for your motorcycle.

Features:

• Designed to provide increased horsepower and torque.
• Pleated media provides a large filtration area, offering long service intervals.
• Multiple layers of woven cotton gauze media offer excellent filtration.
• Application-specific base seal and sealing bead.
• Made in the USA for over 40 years.
• Washable and reusable, pre-oiled and ready to ride!

Specifications:

• Heigh t: 3in (76mm)
• Washable: Yes
• Filter Material: Cotton Gauze
• Filter Re-Oiling Amount: 0.83oz (25ml)

Quantum replacement fuel pumps, regulators, tank seals and strainers are designed to meet or exceed OEM specifications, and feature upgrades that improve on the OEM design. Upgraded polymers, brushes, and commutators ensure long life and durability in multiple fuel blends.

Features & Benefits

• OEM or better performance
• Polished corrosion-resistant case to help minimize seizing during non-operation
• Specifically designed for quiet operation
• Drop-in replacement
• Gradient density fuel strainer for superior contaminant filtration
• Patented check valve technology
• Compatible with modern ethanol-infused pump gasoline

All Balls Fuel Pump Kits are designed to restore lost performance caused by a failing or non-functioning fuel pump. Each kit offers a plug-and-play solution for quick and easy replacement of your OEM fuel pump module.

Kit contents vary by application and may include components such as the pump, filter, hoses, clamps, and wiring harness. Some kits contain only core components like the pump and filter. Please refer to the product image and listing details for exact contents specific to your model.

Features:

• OEM replacement fuel pump kits.
• Plug-and-play installation.
• Contents vary by kit — check image and listing for details.

Please Note:

1. All electrical components must be fitted by a qualified technician.
2. Before fitting electrical components ensure the root cause of the original failure has been addressed.
3. The absence of either of points 1 or 2 above, will void any warranty.

High-quality park hand brake cable from All Balls.

Features:

• Black PVC outer jacket for maximum flexibility and durability.
• Steel inner casing that is tightly coiled for low compression.
• A pre-lubricated nylon inner sleeve guarantees smooth operation and long life.
• All wire ends are bird caged prior to terminal casting for superior pull-out resistance.
• EPDM molded rubber components for high UV resistance and long life.
• Injected molded components are manufactured from high strength POM material.

Features a black PVC outer jacket for maximum flexibility and durability, steel inner casing that is tightly coiled for low compression, pre-lubricated nylon inner sleeve, bird-caged wire ends, EPDM moulded rubber for high UV resistance and injection moulded components manufactured from high-strength POM material.

Features:

• Flexible and durable with steel inner casing that is tightly coiled for low compression.
• Pre-lubricated nylon inner sleeve.
• Bird caged wire ends.
• EPDM moulded rubber for high UV resistance and injection moulded components made from high-strength POM material.

Note: Kit contents may vary by fitment and are subject to change.

RMSTATOR is specialized in designing and manufacturing innovative electrical and electronic components for Powersports vehicles like motorcycles, ATV, SxS, UTV, snowmobiles, and PWC. Through unrelenting quality control, we ensure that each component meets or exceeds the OEM specs. With over 25 product families, rest assured that you will find the part you need.

• Direct replacement to your original unit.
• Plug-and-play, direct fit, easy installation.
• No assembly required
• Higher grade of electric components.
• Improved heat sink and charging capabilities
• The quality exceeds the OEM equipment

RM STATOR has even included the opposite connector (main harness side), as they know these are often melted/corroded/defective and a major cause for repetitive electrical issues.

Battery condition is extremely important. No voltage regulator can work correctly with a bad or weak battery. Always fully charge your battery before performing any charging system tests or replacing parts. If there is any doubt, have the battery load tested or replaced.

Please Note:

1. All electrical components must be fitted by a qualified technician.
2. Before fitting electrical components ensure the root cause of the original failure has been addressed.
3. The absence of either of points 1 or 2 above, will void any warranty.

REPLACEMENT LEFT GRIP FOR THE OXFORD V9 EVO ATV HOT GRIPS

Brand new voltage regulator rectifier

BEWARE: 1996 and early 1997 454 Bearcat 4x4 has a different plug. Please consult installation instruction before buying this product. Arctic Cat split the year on certain models; the RM30405 replaces OEM parts #3430-037 and #3430-016.

• Direct replacement to your original unit.
• Plug-and-play, direct fit, easy installation.
• No assembly required
• Quality exceeds the OEM equipment
• Improved heat sink and charging capabilities
• Higher grade of electric components.
• All products shipped are tested

Dimensions:

• Width: 80mm
• Length: 115mm
• Height: 54mm
• Fixation holes centre to centre: 80mm
• Wires length: 275mm

Other specifications:

• Number of plugs: 1
• Number of pins: 5
• Minimum Charging Voltage: 14.5V +/- 0.5V
• Maximum Charging Current: 25A-35A/300W-500W
• Open Circuit Voltage: <15V
• Operation Temperature: -20° to 85°

Please Note:

1. All electrical components must be fitted by a qualified technician.
2. Before fitting electrical components ensure the root cause of the original failure has been addressed.
3. The absence of either of points 1 or 2 above, will void any warranty.
4. There are multiple regulators for some Triumph vehicles. Please refer to the note below to make sure you purchase the right part:
• Bonneville 2017 to 2020: This part will only fit on Bonneville with a VIN HIGHER than 513325. If you have a LOWER VIN you should look for parts # RM30506 / RM30506H / RMS022-105928 / RMS023 106203 / RMS023-107140.
• Thruxton from 2008 to 2020 This part will only fit Thruxton with a VIN HIGHER than 513322. If your vehicle has a VIN inferior to 513321, refer to OEM T1300890.

GOLDfren began manufacturing sintered disc brake pads for a wide range of off-road and road motorcycles in 1991, nearly three decades on from their first motorcycle brake pads GOLDfren has become one of the largest aftermarket manufacturers in the motorcycle brake disc pad industry. Their development of next-generation products has kept them at the technological forefront of Sintered Friction Braking providing you with confidence in the performance, durability and reliability of your brakes.

K5 Series:

The K5 sintered compound is optimal for off-road motorcycles and ATVs. It is recommended for riders who demand great off-road stopping power and brake pad durability when riding on tough off-road terrains. The K5 series is designed for low abrasive interaction with the rotor, long life and self-cleaning capabilities necessary in off-road riding conditions. Friction materials contain metal-ceramic with a sophisticated bronze-graphite and full-metal mixture formulation with fine friction particles to achieve optimal friction properties.

Features:

• High static friction coefficient
• Good abrasive resistance
• Self-cleaning capability
• Low abrasive interaction with the brake rotor material
• Up to 3 times longer operational life compared to organic and Kevlar composite materials

Application:

• Developed specifically for off-road motorcycles & ATVs
• Can be used on both front and rear brakes
• Could be used on the rear brake of road racing motorcycles

Operating Parameters:

• Specific pressure: 2.0 Mpa
• Sliding velocity: 20 m/s
• Constant maximum temp: 500°C
• Short time maximum temp: 750°C
• Counter-surfaces: steel disks

What is a sintered brake pad?

GOLDfren only manufacturers sintered brake pads that contain metal-ceramic and ceramic-carbon friction materials, these materials allow for less brake dust and a quieter braking experience. Sintered brake pads are made by fusing together metallic particles under high temperature and pressure which enhances friction properties and pad life, resulting in longer life and stronger braking. Sintered brake pads experience no brake fade when operating at high temperatures and in wet conditions. They also last up to 5 times longer than organic pads and provide additional braking strength. All materials used are environmentally friendly and do not contain any lead, asbestos, fibreglass or formaldehyde.

Reminder: one set of brake pads services one brake disc, if you are servicing multiple discs you will need multiple sets of brake pads.

Crafted from military-spec certified TI3Al titanium alloy, Vertex Titanium Valves are made to endure the harshest racing conditions. Forged from a single blank, grain flow is improved to enhance the mechanical characteristics of the valve without having to resort to welding. Special PVD, CVD, and CrN coatings are used to provide low-friction surfaces that reduce heat generation and resist carbon build-up; coatings allow alloys like titanium to become ultra-smooth while reaching hardness levels 5x that of high-speed steel.

• Military-spec certified TI3Al titanium alloy
• Forged from a single blank
• PVD, CVD, and CrN coatings
• Reduces heat generation
• Resists carbon build-up
• Significantly stronger than steel

RMSTATOR is specialized in designing and manufacturing innovative electrical and electronic components for Powersports vehicles like motorcycles, ATV, SxS, UTV, snowmobiles, and PWC. Through unrelenting quality control, we ensure that each component meets or exceeds the OEM specs. With over 25 product families, rest assured that you will find the part you need.

• Direct replacement to your original unit
• Plug-and-play, direct fit, easy installation
• Highest grade of lamination materials
• Highest grade of copper winding, resistant to 200 degrees Celsius
• Connector included

Battery condition is extremely important. No stator can work correctly with a bad or weak battery. Always fully charge your battery before performing any charging system tests or replacing parts. If there is any doubt, have the battery load tested or replaced.

Please Note:

1. All electrical components must be fitted by a qualified technician.
2. Before fitting electrical components ensure the root cause of the original failure has been addressed.
3. The absence of either of points 1 or 2 above, will void any warranty.

High-quality lower rear shock bearing kit from All Balls.

This kit contains all the bearings required to rebuild your lower rear shock to factory specifications.

NOTE: This Vertex Top End Gasket Set contains all components pictured.

Produced in the U.S.A. with the latest materials and technology in gasket production to Vertex specifications. Vertex gaskets ensure long-lasting performance and leak prevention for your rebuild needs. Vertex's replacement gaskets and seals are available as top-end kits, complete engine kits, or as an oil seal kit.

• These sets include the head, base, and exhaust gaskets, valve seals, O-rings and other gaskets to complete a top-end rebuild.

All the bearings and seal required to refit a wheel in one convenient package.

Features:

• Premium high-speed bearings feature low drag.
• Double lip seals on both sides to provide superior exclusion of water and dirt
• Improved grease retention.

• Direct OEM replacement at a fraction of the cost
• Includes valve, hose, gaskets, screws, clamps and everything needed to replace the OEM petcock
• Viton rubber fuel resistant gaskets
• Includes OE style fuel line and clamps

NOTE: This complete Vertex Gasket Set contains all components pictured.

Produced in the U.S.A. with the latest materials and technology in gasket production to Vertex specifications. Vertex gaskets ensure long-lasting performance and leak prevention for your rebuild needs. Vertex's replacement gaskets and seals are available as top-end kits, complete engine kits, or as an oil seal kit.

• One kit containing all of the gaskets, O-rings, and valve seals necessary to rebuild the entire engine and transmission
• Note: Does NOT include transmission seals

Kit includes components to rebuild one wheel. Includes wheel studs, nuts, washers, and other miscellaneous components.

NOTE: This Vertex Top End Gasket Set contains all components pictured.

Produced in the U.S.A. with the latest materials and technology in gasket production to Vertex specifications. Vertex gaskets ensure long-lasting performance and leak prevention for your rebuild needs. Vertex's replacement gaskets and seals are available as top-end kits, complete engine kits, or as an oil seal kit.

• These sets include the head, base, and exhaust gaskets, valve seals, O-rings and other gaskets to complete a top-end rebuild.