HARD PARTS

Quality design and construction of every All Balls piece meets the toughest standards and conditions - from daily commuting to full-on racing, all older bearing and seal designs are upgraded to the best and latest specs and designs.

Available individually in left-hand and right-hand thread or sold in pairs one L/H and one R/H thread.

Why use the SPLYT Technology?

As featured by Dirt Trax Television, RMSTATOR SPLYT Technology provides a reliable solution to well-known charging system failures. Using a dual output stator with two completely separate stator windings, this system splits the power generated by the stator into two separate voltage regulators. These regulators then each operate with only half of the load of the original system, allowing them to maintain a lower temperature and increase reliability.

SERIES Voltage Regulation

This system uses a new type of voltage regulator called a SERIES regulator. Rather than shunting excess power to the ground like a typical regulator, it protects the battery from high voltage by disconnecting the stator coils from the regulator and preventing current from passing on. This type of voltage regulation generates less heat because the current from the stator is prevented from flowing through the regulator.

Ultimate reliability

With a stock charging system, voltage regulators are consistently operating within 5% of their maximum capacity, leading to heat and stress-related failure. With the RMSTATOR SPLYT system, both SERIES voltage regulators are operating with 40% overhead for long life and stable output.

Better design

Contrary to the original OEM stator that uses one three-phase stator winding, the SPLYT stator contains two completely separate three-phase coil windings. Each of these two windings then produces half of the power of the stock stator lowering the temperature in each individual coil.

More available power

If you are installing a lot of accessories and electronics on your vehicles, like extra lighting, stereos or a winch,
the SPLYT kit is available with an improved flywheel designed to increase power output from 650 Watts to 900 Watts.

Easy to install

All parts use a Plug-and-Play design, just like the original OEM ones, so no special tool or knowledge is needed to install this system.

Harnesses included

Relocation wiring harnesses allow relocating the regulators anywhere on your vehicle to get better airflow and easier access.

This kit includes:

• Dual output stator
• Two SERIES voltage regulators
• Two automotive-grade relocation wiring harnesses with OEM-quality heavy-duty connectors
• Complete instructions for voltage regulator relocation

Specifications:

• Dual Stator Dimensions:
• Interior diameter: 53 mm
• Exterior diameter: 125 mm
• Thickness: 26 mm
• Length of wires stator to grommet: 125 mm
• Length of wires grommet to plug: 290 mm & 550 mm
• Other specifications:
• Number of wires: 6
• Number of plugs: 2
• Number of pins: 6
• Number of poles: 18
• Alternator: Yellow/Black to Yellow/Black = 0.5 ohms +-20%
• Regulator Dimensions:
• Width: 84 mm
• Length: 90 mm
• Height: 32 mm
• Fixation holes center to center: 69 mm
• Other specifications:
• Number of plugs: 2
• Number of pins: 5
• Minimum Charging Voltage: 14.5 V +- 0.5 V
• Maximum Charging Current: 50 A / 500 W
• Open Circuit Voltage: < 15 V
• Operation Temperature: -20º to 85º
• Relocation Harness Dimensions
• Wires length : 3400 mm
• Number of yellow wires : 3
• Number of red wires : 1
• Number of black wires : 1
• Number of plugs : 2

Note: This kit includes two wiring harness according to Polaris recal # Z-16-01-C (OEM # 2206620, 2206367,2206473). We strongly suggest you to relocate both of your regulators to make sure they do not wear out prematurely due to mud, dust or rocks.

Brand new aftermarket Voltage Regulator Rectifier

• Direct replacement to your original unit
• Plug-and-play, direct fit, easy installation
• No assembly required
• Higher grade of electric components
• The quality exceeds the OEM equipment
• All products shipped are tested

All item pictures are accurate, if in doubt, do not hesitate and compare our item to your original part.

Specifications:

Dimensions:

• W idth: 64 mm
• Length: 86 mm
• Height: 20 mm
• Distance between fixation holes center to center: 65 mm

Other specifications:

• Number of plugs: 1
• Number of pins: 4
• Minimum Charging Voltage: 14.5 V +- 0.5 V
• Maximum Charging Current: 50 A / 500 W
• Open Circuit Voltage: < 15 V
• Operation Temperature: -20°C to 85°C

Note: Battery condition is important. No regulator can make up for a bad or weak battery. If in doubt charge your battery and have it load tested, or simply replace it. ALWAYS START WITH A FULLY CHARGED BATTERY

Each pack of Premier CSK Clutch Springs contains a complete set of heavy-duty springs. Up to 15% stronger than the original.

Customer should be advised that after installation of a CSK kit the clutch lever will feel slightly ‘heavier’ than standard

Quality design and construction of every All Balls piece meets the toughest standards and conditions - from daily commuting to full-on racing, all older bearing and seal designs are upgraded to the best and latest specs and designs.

Available individually in left-hand and right-hand thread or sold in pairs one L/H and one R/H thread.

Quality replacement Regulator/Rectifiers.

Please Note:

1. All electrical components must be fitted by a qualified technician.
2. Before fitting electrical components ensure the root cause of the original failure has been addressed.
3. The absence of either of points 1 or 2 above, will void any warranty.

Whites aluminium radiators make great replacements to your bent, cracked, and damaged radiators. Whites radiators offer exceptional cooling and maximum efficiency to ensure your machine's top performance. Based on the OEM specs, a hand-welded aluminium design offers both a great fit and styling. All cap side radiators will include a new radiator cap.

Add a little extra style and functionality to your motorcycle with Whites quality products.

Whites radiators offer exceptional cooling and maximum flow efficiency to ensure your machines top performance
Utilizes stock mounting hardware (not included) for a great fit
Hand-welded aluminium design for a great look and functionality
Includes a new radiator cap

All Balls OEM replacement air filters are manufactured to meet or exceed OEM specifications. Constructed to fit the factory air box and are direct replacements to OEM air filters. The premium filtering media prevents dirt and dust from entering your engine while maintaining excellent airflow.

• OEM replacement air filter
• Meets or exceeds OEM specifications
• Fits factory air box
• Excellent airflow
• Premium filtration

A quality alternative to expensive OEM bearings and seals. >Replacement crankshaft main bearing and seal kit

HFP replacement fuel pumps, modules, and assemblies are designed to meet or exceed OEM specifications, and feature upgrades that improve on the OEM design. Upgraded polymers, brushes, and commutators ensure long life and durability in multiple fuel blends.

• OEM or better performance
• Polished corrosion-resistant case to help minimize seizing during non-operation
• Specifically designed for quiet operation
• Drop-in replacement
• Gradient density fuel strainer for superior contaminant filtration (intank pumps only)
• Patented check valve technology
• Compatible with modern ethanol-infused pump gasoline

GOLDfren began manufacturing sintered disc brake pads for a wide range of off-road and road motorcycles in 1991, nearly three decades on from their first motorcycle brake pads GOLDfren has become one of the largest aftermarket manufacturers in the motorcycle brake disc pad industry. Their development of next-generation products has kept them at the technological forefront of Sintered Friction Braking providing you with confidence in the performance, durability and reliability of your brakes.

S3 Series:

The S3 sintered compound is optimal in dry and wet conditions for road & off-road motorcycles. For the road application, S3 pads are suitable for both the front and rear brake while on off-road applications the S3 is only recommended for the front brake. The S3 series is designed for low abrasive interaction with the rotor and quieter braking due to the ceramic composite material. It has an HH friction rating and performs better at higher temperatures than the AD compound. Friction materials contain metal-ceramic with a bronze-graphite and non-metallic friction additives are spread evenly on the base fine bronze body to achieve optimal friction properties.

Features:

• Very high static friction coefficient
• Minimal difference between wet and dry braking performance
• Good abrasive resistance
• Low abrasive interaction with the brake rotor material
• Longer life compared to organic and Kevlar composite materials

Application:

• For riders who demand a bit more than average from their bikes
• Recommended on both front and rear brakes (road application)
• Can also be used on the front brakes of off-road bikes and ATVs
• Works well on both dry and wet conditions

Operating Parameters:

• Specific pressure: 3.0 Mpa
• Sliding speed: 45 m/s
• Constant maximum temp: 450°C
• Short time maximum temp: 800°C
• Counter-surfaces: steel disks

What is a sintered brake pad?

GOLDfren only manufacturers sintered brake pads that contain metal-ceramic and ceramic-carbon friction materials, these materials allow for less brake dust and a quieter braking experience. Sintered brake pads are made by fusing together metallic particles under high temperature and pressure which enhances friction properties and pad life, resulting in longer life and stronger braking. Sintered brake pads experience no brake fade when operating at high temperatures and in wet conditions. They also last up to 5 times longer than organic pads and provide additional braking strength. All materials used are environmentally friendly and do not contain any lead, asbestos, fibreglass or formaldehyde.

Reminder: one set of brake pads services one brake disc, if you are servicing multiple discs you will need multiple sets of brake pads.

Carburetor repair kits

• Kits include all of the necessary components to repair a carburetor. ATV models with two carburetors include components to repair two carburetors.
• Kit includes necessary all O-rings, gaskets, jets, needle, mixture screw, float bowl screws, float valve needle and seat. (Needle jet and other pressed in jets are not included in kit.)
• OEM jet sizes are included in the kit. NBR rubber material is used on all O-rings and rubber gaskets NBR has excellent resistance to the ethanol used in today’s fuels.
• Applications that use paper float bowl gaskets are upgraded to High Performance Interface Gasket material.
• Components included in the kits are based off of US models and discretion must be used when attempting to install the kit on a non US model.
• Off road use only.

All the bearings and seal required to refit a wheel in one convenient package.

Features:

• Premium high-speed bearings feature low drag.
• Double lip seals on both sides to provide superior exclusion of water and dirt
• Improved grease retention.

Ideal replacement for dirt bikes.

Features:

• Anti-swell alloy impregnated heavy-duty cork-based facings.
• Smooth clutch take up compared to paper clutches, which can ‘snatch’.
• Steel separator plates increase flywheel effect of the engine and improve performance.

Wossner

For more than 35 years, Wössner successfully design and produce high-performance pistons and connecting rods.

In order to offer their customers the best of Wössner Power, their products are produced by using state-of-the-art technology and are subject to continuous quality control.

Performance, quality and longevity - this is what Wössner stands for with high-quality products.

Needle Bearings (Little End Bearings)

Please use our Fitments Tool to ensure the correct part is ordered.

A quality CV Boot Kit from All Balls. Comes complete with CV Boot, clamps and grease.

Produced in the U.S.A. with the latest materials and technology in gasket production to Vertex specifications. Vertex gaskets ensure long-lasting performance and leak prevention for your rebuild needs. Vertex's replacement gaskets and seals are available as top-end kits, complete engine kits, or as an oil seal kit.

• One kit containing all of the gaskets necessary to rebuild the water pump.
• Designed to fit O.E.M. water pump.

P SERIES - Street Bikes

Premier's most successful general use material, our P series pads, are a tough Kevlar based organic material giving superb brake effect on all sportbikes and cruisers. This material is preselected by the catalogue when you order P prefix disc pads.

P SERIES - Off-Road

Part numbers relating to off-road machines are supplied in carbon graphite compound for medium durability, good brake effect and minimum heat generation.

NOTE: This Vertex Top End Gasket Set contains all components pictured.

Produced in the U.S.A. with the latest materials and technology in gasket production to Vertex specifications. Vertex gaskets ensure long-lasting performance and leak prevention for your rebuild needs. Vertex's replacement gaskets and seals are available as top-end kits, complete engine kits, or as an oil seal kit.

• These sets include the head, base, and exhaust gaskets, valve seals, O-rings and other gaskets to complete a top-end rebuild.

Up to 40% stronger than OE axles, these complete axles feature enlarged CV joints, bearing cages, and chromoly axle shafts. All internal components are precision ground and utilize molybdenum grease.

Features:

• 40% stronger than OEM.
• Larger 4340 chrome-moly steel axle bar.
• Precision ground components.
• Low profile clamps.
• Neoprene boots.
• Engineered in the USA.
• Manufactured in an ISO facility.
• Assembled with 3% moly grease.
• Black oxide coating to resist rust and corrosion.

P SERIES - Street Bikes

Premier's most successful general use material, our P series pads, are a tough Kevlar based organic material giving superb brake effect on all sportbikes and cruisers. This material is preselected by the catalogue when you order P prefix disc pads.

P SERIES - Off-Road

Part numbers relating to off-road machines are supplied in carbon graphite compound for medium durability, good brake effect and minimum heat generation.

K&N off-road replacement air filters are ideal for extended use in dirty and dusty off-road riding and provide clean carburetion even at high altitude. Generally, no jet changes are required with just a K&N filter element. K&N replacement air filters are washable and reusable and provide high airflow with excellent filtration.

Features:

• Designed to provide increased horsepower and acceleration.
• Pleated cotton media provides a large filtration area offering low restriction, high-capacity and long service intervals.
• Multiple layers of woven cotton gauze media offer excellent filtration.
• Fits directly into OEM airbox with an application-specific sealing bead ensuring a precise fit.
• No fuel management modifications are required to obtain increased performance.
• Washable and reusable, most are pre-oiled and ready to ride.

Specifications:

• Height: 8.75in (222mm)
• Washable: Yes
• Filter Material: Cotton Gauze
• Outside Length: 6.125in (156mm)
• Outside Width: 4.25in (108mm)
• Weight: 2.1 lb (0.9kg)
• Filter Re-Oiling Amount: 1.66oz (49ml)

Quality carburettor rebuild kit from All Balls.

• Kits include all of the necessary components to repair a carburettor. ATV models with two carburettors include components to repair two carburettors.
• Kit includes necessary all O-rings, gaskets, jets, needle, mixture screw, float bowl screws, float valve needles and seat. (Needle jet and other pressed-in jets are not included in the kit.)
• OEM jet sizes are included in the kit. NBR rubber material is used on all O-rings and rubber gaskets NBR has excellent resistance to the ethanol used in today’s fuels.
• Applications that use paper float bowl gaskets are upgraded to High-Performance Interface Gasket material.
• Components included in the kits are based on US models and discretion must be used when attempting to install the kit on a non-US model.
• Off-road use only.

Includes components necessary to complete a piston (top end) rebuild. Competitive pricing, made to meet and exceed OEM quality and designed as a direct OEM replacement.

Features:

• Designed for OEM replacement.
• Made from high-quality materials.
• Meet or exceed OEM specifications.
• Competitive pricing.

All Balls Wheel Bearing Kit

Hands down, the most complete line of wheel bearing & seal kits!
All the bearings and seals required to refit a wheel in one convenient package.
Premium high-speed bearings feature low drag, double lip seals on both sides to provide superior exclusion of water and dirt and improved grease retention.
High performance Chevron SRI-II grease features special rust inhibitors for the most demanding applications.
Type TC, Nitrile Elastomer wheel seals are specifically designed to keep out water and dirt whilethe rubber coated outside diameter creates an optimum seal at the hub.
Quality design and construction of every All Balls piece meets the toughest standards and conditions - from daily commuting to full-on racing, all older bearing and seal designs are upgraded to the best and latest specs and designs.

All the bearings and seal required to refit a wheel in one convenient package.

Features:

• Premium high-speed bearings feature low drag.
• Double lip seals on both sides to provide superior exclusion of water and dirt
• Improved grease retention.

Produced in the U.S.A. with the latest materials and technology in gasket production to Vertex specifications. Vertex gaskets ensure long-lasting performance and leak prevention for your rebuild needs. Vertex's replacement gaskets and seals are available as top-end kits, complete engine kits, or as an oil seal kit.

• One kit containing all of the gaskets necessary to rebuild the water pump.
• Designed to fit O.E.M. water pump.