HARD PARTS

Filters designed to fit with cut velocity stacks or straight pieces of exhaust tubing. Rubber filter bases come with moulded in velocity stack type radius and step, for smooth bore down from element to tube. Each filter has a rubber top with a stamped K&N logo. As with all K&N air filters, these are washable and reusable. Simply use K&N oil and cleaner to service your filter.

Features:

• Low restriction.
• Clamp-on design.
• Washable and reusable.
• Outstanding filtration.

Specifications:

• Filter Material: Cotton Gauze
• Outside Diameter: 89mm
• Height: 127mm
• Flange Inside Diameter: 54mm
• Flange Length: 25mm
• Flange Type: Angled
• Flange Angle: 5 degrees

Produced in the U.S.A. with the latest materials and technology in seal production to Vertex specifications. Vertex seals ensure long-lasting performance and leak prevention for your rebuild needs.

Features:

• OEM replacement mechanical water pump seal.
• High-quality seal face material seals better and lasts longer.
• Corrosion and chemical-resistant materials keep your engine clean, safe and cool.
• Meets or exceeds OEM quality.

KoubaLink specialises in motorcycle lowering and performance linkages for off-road and dual-sport rear suspension systems. Compromise is not an option at KoubaLink. Listening to riders from all over the world explain where and how they use their off-road and dual-sport bikes. With their input, Koubalink manufacture products that add to your motorcycling experience and make it a little more enjoyable.

Features:

• Provides better front-end stability by lowering rear suspension geometry.
• Machined from billet aluminium.
• Stronger than OEM.
• Pre-installed OE style bearings included.
• Replace linkage like its OEM.
• Includes all required bearings and seals for assembly (Excluding Dog Bone styled linkages that do not include bearings and seals from factory).

Please Note:

1. All electrical components must be fitted by a qualified technician.
2. Before fitting electrical components ensure the root cause of the original failure has been addressed.
3. The absence of either of points 1 or 2 above, will void any warranty.

Upgrades rubber bushings found in Utility ATV A-Arms to ABs redesigned HD Delrin bushings. Designed to replace worn-out rubber bushings and provide greater suspension travel and performance.

GOLDfren began manufacturing sintered disc brake pads for a wide range of off-road and road motorcycles in 1991, nearly three decades on from their first motorcycle brake pads GOLDfren has become one of the largest aftermarket manufacturers in the motorcycle brake disc pad industry. Their development of next-generation products has kept them at the technological forefront of Sintered Friction Braking providing you with confidence in the performance, durability and reliability of your brakes.

S3 Series:

The S3 sintered compound is optimal in dry and wet conditions for road & off-road motorcycles. For the road application, S3 pads are suitable for both the front and rear brake while on off-road applications the S3 is only recommended for the front brake. The S3 series is designed for low abrasive interaction with the rotor and quieter braking due to the ceramic composite material. It has an HH friction rating and performs better at higher temperatures than the AD compound. Friction materials contain metal-ceramic with a bronze-graphite and non-metallic friction additives are spread evenly on the base fine bronze body to achieve optimal friction properties.

Features:

• Very high static friction coefficient
• Minimal difference between wet and dry braking performance
• Good abrasive resistance
• Low abrasive interaction with the brake rotor material
• Longer life compared to organic and Kevlar composite materials

Application:

• For riders who demand a bit more than average from their bikes
• Recommended on both front and rear brakes (road application)
• Can also be used on the front brakes of off-road bikes and ATVs
• Works well on both dry and wet conditions

Operating Parameters:

• Specific pressure: 3.0 Mpa
• Sliding speed: 45 m/s
• Constant maximum temp: 450°C
• Short time maximum temp: 800°C
• Counter-surfaces: steel disks

What is a sintered brake pad?

GOLDfren only manufacturers sintered brake pads that contain metal-ceramic and ceramic-carbon friction materials, these materials allow for less brake dust and a quieter braking experience. Sintered brake pads are made by fusing together metallic particles under high temperature and pressure which enhances friction properties and pad life, resulting in longer life and stronger braking. Sintered brake pads experience no brake fade when operating at high temperatures and in wet conditions. They also last up to 5 times longer than organic pads and provide additional braking strength. All materials used are environmentally friendly and do not contain any lead, asbestos, fibreglass or formaldehyde.

Reminder: one set of brake pads services one brake disc, if you are servicing multiple discs you will need multiple sets of brake pads.

Features a black PVC outer jacket for maximum flexibility and durability, steel inner casing that is tightly coiled for low compression, pre-lubricated nylon inner sleeve, bird-caged wire ends, EPDM moulded rubber for high UV resistance and injection moulded components manufactured from high-strength POM material.

Features:

• Flexible and durable with steel inner casing that is tightly coiled for low compression.
• Pre-lubricated nylon inner sleeve.
• Bird caged wire ends.
• EPDM moulded rubber for high UV resistance and injection moulded components made from high-strength POM material.

Note: Kit contents may vary by fitment and are subject to change.

Fuel pump strainers act as a first line of defence against fuel system contamination. Strainers filter out common contaminants found in gasoline such as dirt, dust and other particulate matter, as well as gasoline varnish. Quantum fuel pump strainers feature multiple layers of strainer media to filter progressively smaller particle sizes. The expanded surface area provides enhanced filtration, extending the life of the fuel pump.

Restricted fuel flow through a clogged strainer causes the fuel pump to work harder, reducing pump longevity. Strainer clogging is among the top causes of fuel pump failure making it important to replace your strainer regularly - before problems arise. We recommend replacing fuel pump strainers in powersports applications once a year as part of a preventative maintenance plan.

Features:

• Designed with gradient density to meet or exceed OE specifications.
• Designed to ensure optimal filtration to prevent fuel system contamination.
• Strainer material tested and validated for capacity and efficiency by accredited third party.

Brake shoes 

Each pack of Premier CSK Clutch Springs contains a complete set of heavy-duty springs. Up to 15% stronger than the original.

Customer should be advised that after installation of a CSK kit the clutch lever will feel slightly ‘heavier’ than standard

NOTE: This Vertex Top End Gasket Set contains all components pictured.

Produced in the U.S.A. with the latest materials and technology in gasket production to Vertex specifications. Vertex gaskets ensure long-lasting performance and leak prevention for your rebuild needs. Vertex's replacement gaskets and seals are available as top-end kits, complete engine kits, or as an oil seal kit.

• These sets include the head, base, and exhaust gaskets, valve seals, O-rings and other gaskets to complete a top-end rebuild.

The Whites OEM replacement cast levers provide an economical alternative to original levers. The perfect spare to have ready in your workshop in case of race day disaster. Available in black and OEM silver finish (model dependent).

Features:

• Direct OEM replacement cast levers.
• Designed to exceed OEM specifications.
• Built to resist breakage.
• Designed to fit OEM perch.
• Made from die-cast aluminum for maximum durability and affordability.

Rough riding calls for stronger axles and that’s where All Balls Racing excels. Machined for exact OEM fit, the shaft is made of chromoly steel with a larger diameter than most axles. The axle has 6 ball bearings in each CV joint. Laminate coating resists corrosion and rust and protects axles from dirt, water, rocks and grease. Waterproof neoprene boots act as a first line of defence, shielding vulnerable joints and preventing leaks. High-performance molybdenum grease reduces heat and friction.

In static torsion trials, these axles were up to 30% stronger than OEM and aftermarket competition.

Features:

• 40% stronger than OEM.
• Larger 4340 chrome-moly steel axle bar.
• Precision ground components.
• Low profile clamps.
• Lasts approximately 50 percent longer than many aftermarket competitors.
• Neoprene boots.
• Typically runs almost 130,000 cycles versus 80,000 cycles for many axles.
• Engineered in the USA.
• Manufactured in an ISO facility.Assembled with 3% molybdenum grease.

NOTE: This Vertex Top End Gasket Set contains all components pictured.

Produced in the U.S.A. with the latest materials and technology in gasket production to Vertex specifications. Vertex gaskets ensure long-lasting performance and leak prevention for your rebuild needs. Vertex's replacement gaskets and seals are available as top-end kits, complete engine kits, or as an oil seal kit.

• These sets include the head, base, and exhaust gaskets, valve seals, O-rings and other gaskets to complete a top-end rebuild.

K&N's high-flow air filters are available as a replacement for your stock motorcycle air filter element. They are custom-engineered to fit your specific application and are designed to provide low restriction and increased performance, while providing excellent engine protection for your motorcycle.

Features:

• Designed to provide increased horsepower and torque.
• Pleated media provides a large filtration area, offering long service intervals.
• Multiple layers of woven cotton gauze media offers excellent filtration.
• Application-specific base seal and sealing bead.
• Made in the USA for over 40 years.
• Washable and reusable, pre-oiled and ready to ride!

Specifications:

• Washa ble: Yes
• Filter Material: Cotton Gauze
• Height: 25mm
• Outside Length: 148mm
• Outside Width: 169mm
• Filter Re-Oiling Amount: 15ml

Wrench Rabbit Rebuild Kits have been rebranded to Vertex Rebuild Kits; all components remain unchanged however you may receive a kit that is boxed differently to the one pictured.

Vertex Complete Engine Rebuild Kits are a simple and cost-effective way to complete a top-to-bottom professional rebuild for your 2 or 4-stroke motorcycle or ATV/UTV. The one easy to order kit will not only save you time by offering a one-stop-shop in a box, but they also save you money when compared to purchasing all items individually.

Vertex kits include quality components from Vertex, Hot Rods & Hot Cams.*

All parts are manufactured in the USA from the highest quality material.

Features:

• Crafted to deliver unbeatable levels of quality
• High-grade materials for exceptional performance
• Superior in durability and reliability
• Kits available for many 2 & 4-stroke motorcycles, ATVs & UTVs
• Cost-effective solution
• Saves time sourcing individual components
• Vertex pistons & gaskets*
• Hot Rods crank & bearing kits*
• Hot Cams cam chain*

Includes:

• Crankshaft
• Piston Kit
• Complete Engine Gasket Kit
• Oil Seal Kit
• Main Bearing and Seal Kit
• Water Pump Rebuild Kit
• Transmission Bearing Kit
• Countershaft Bushing/Seal Kit
• Cam Chain

*Specific parts vary by kit (see included parts above).

Fuel pump strainers act as a first line of defense against fuel system contamination. Strainers filter out common contaminants found in gasoline such as dirt, dust and other particulate matter, as well as gasoline varnish. Quantum fuel pump strainers feature multiple layers of strainer media to filter progressively smaller particle sizes. The expanded surface area provides enhanced filtration, extending the life of the fuel pump.

Restricted fuel flow through a clogged strainer causes the fuel pump to work harder, reducing pump longevity. Strainer clogging is among the top causes of fuel pump failure making it important to replace your strainer regularly - before problems arise. We recommend replacing fuel pump strainers in powersports applications once a year as part of a preventative maintenance plan.

Features:

• Designed with gradient density to meet or exceed OE specifications
• Designed to ensure optimal filtration to prevent fuel system contamination
• Strainer material tested and validated for capacity and efficiency by accredited third party

Quantum replacement fuel pumps, regulators, tank seals and strainers are designed to meet or exceed OEM specifications, and feature upgrades that improve on the OEM design. Upgraded polymers, brushes, and commutators ensure long life and durability in multiple fuel blends.

Features & Benefits

• OEM or better performance
• Polished corrosion-resistant case to help minimize seizing during non-operation
• Specifically designed for quiet operation
• Drop-in replacement
• Gradient density fuel strainer for superior contaminant filtration
• Patented check valve technology
• Compatible with modern ethanol-infused pump gasoline

HFP replacement fuel pumps, modules, assemblies, and kit components are designed to meet or exceed OEM specifications, and feature upgrades that improve on the OEM design. Upgraded polymers, brushes, and commutators ensure long life and durability in multiple fuel blends.

• OEM or better performance
• Polished corrosion-resistant case to help minimize seizing during non-operation
• Specifically designed for quiet operation
• Drop-in replacement
• Gradient density fuel strainer for superior contaminant filtration
• Patented check valve technology
• Compatible with modern ethanol-infused pump gasoline

A Quality Fork Bush from All Balls Racing. 

*This is just a single bush

• Direct OEM replacement fuel line clamp kit
• This ultimate fuel line clamp kit is an absolute necessity for any shop, technician, or DIY mechanic
• Kit contains 4 of each Fuel Star fuel line OEM replica clamps, available in sizes from 7-17mm I.D.
• Each clamp is an exact replica of the major OEM's fuel line clamps and is manufactured to meet or exceed OEM performance, aesthetics, and fit
• 4-packs also available to refill the kit

K&N's high-flow air filters are available as a replacement for your stock motorcycle air filter element. They are custom-engineered to fit your specific application and are designed to provide low restriction and increased performance while providing excellent engine protection for your motorcycle.

Features:

• Designed to provide increased horsepower and torque.
• Pleated media provides a large filtration area, offering long service intervals.
• Multiple layers of woven cotton gauze media offer excellent filtration.
• Application-specific base seal and sealing bead.
• Made in the USA for over 40 years.
• Washable and reusable, pre-oiled and ready to ride!

Specifications:

• Filte r Material: Cotton Gauze
• Washable: Yes
• Height: 0.813in (21mm)
• Outside Length: 10.063in (256mm)
• Outside Width: 5.813in (148mm)
• Filter Re-Oiling Amount: 0.95oz (28ml)

Each pack of Premier CSK Clutch Springs contains a complete set of heavy-duty springs. Up to 15% stronger than the original.

Customer should be advised that after installation of a CSK kit the clutch lever will feel slightly ‘heavier’ than standard