HARD PARTS

K&N's high-flow air filters are available as a replacement for your stock motorcycle air filter element. They are custom-engineered to fit your specific application and are designed to provide low restriction and increased performance, while providing excellent engine protection for your motorcycle.

Features:

• Designed to provide increased horsepower and torque.
• Pleated media provides a large filtration area, offering long service intervals.
• Multiple layers of woven cotton gauze media offer excellent filtration.
• Application-specific base seal and sealing bead.
• Made in the USA for over 40 years.
• Washable and reusable, pre-oiled and ready to ride!

Specifications

• Washab le: Yes
• Filter Material: Cotton Gauze
• Height: 38mm
• Inside Diameter: 151mm
• Outside Diameter: 113mm
• Filter Re-Oiling Amount: 11ml

Ideal replacement for dirt bikes.

Features:

• Anti-swell alloy impregnated heavy-duty cork-based facings.
• Smooth clutch take up compared to paper clutches, which can ‘snatch’.
• Steel separator plates increase flywheel effect of the engine and improve performance.

Please Note:

1. All electrical components must be fitted by a qualified technician.
2. Before fitting electrical components ensure the root cause of the original failure has been addressed.
3. The absence of either of points 1 or 2 above, will void any warranty.

Replaces leaky seals and bushings behind countershaft sprockets. Competitively priced against OEM parts. Quick solution to repairing a leaking counter shaft seal in one complete kit.

Includes:

• Hot Rods countershaft seal
• Countershaft bushing
• O-rings
• Sprocket nut washer (where applicable)

Note:

Does not include water pump bearings or transmission bearings.

PH SERIES – Street Sport Sintered

High-performance HH friction rated sintered metal pads made in the USA to an exclusive Premier formulation. PH brake pads offer maximum durability and unbeatable performance under heavy braking and high-speed use. PH series is no longer available for off-road applications following the formulation improvements of the PR range for Moto-X and ATV applications.

Dynamically balanced to reduce noise and vibration, lengthening its life and the time between re-servicing. All Balls Stealth Drive Prop Shafts include a carrier bearing to reduce cost, ease assembly and provide a complete ready-to-install driveline, out of the box.

Features:

• Phased pairs are balanced and phased as complete, two-piece assemblies.
• Designed with the same dimensions as O.E.M. drive shafts for guaranteed fitment.
• Greaseable U-joints allow maintenance of the drive shaft.

NOTE: This complete Vertex Gasket Set contains all parts as pictured.

Produced in the U.S.A. with the latest materials and technology in gasket production to Vertex specifications. Vertex gaskets ensure long-lasting performance and leak prevention for your rebuild needs. Vertex's replacement gaskets and seals are available as top-end kits, complete engine kits, or as an oil seal kit.

• One kit containing all of the gaskets, O-rings, and valve seals necessary to rebuild the entire engine and transmission.
• Includes transmission seals.

All new assembly sold complete with Hot Rods connecting rod.

• The Hot Rods complete crankshaft includes their famed connecting rod; durability at a level OEM rods can only dream of.
• Factory assembled and trued to O.E.M. specifications, Hot Rods cranks will meet or surpass the OEM in performance. Hot Rods makes installing the complete crankshaft simple and easy.
• Crankshaft is completely rebuildable with genuine Hot Rods connecting rods.

Note: Crank bearings and seals sold separately.

Quality design and construction of every All Balls piece meets the toughest standards and conditions - from daily commuting to full-on racing, all older bearing and seal designs are upgraded to the best and latest specs and designs.

Available individually in left-hand and right-hand thread or sold in pairs one L/H and one R/H thread.

All new assembly sold complete with Hot Rods connecting rod.

• The Hot Rods complete crankshaft includes their famed connecting rod; durability at a level OEM rods can only dream of.
• Factory assembled and trued to O.E.M. specifications, Hot Rods cranks will meet or surpass the OEM in performance. Hot Rods makes installing the complete crankshaft simple and easy.
• Crankshaft is completely rebuildable with genuine Hot Rods connecting rods.

Note: Crank bearings and seals sold separately.

XAM chain and sprocket kits are the perfect drive maintenance kit for your bike. The perfect alternative to expensive OEM replacements, it is designed to meet and exceed OEM specifications. Supplied in presentable packaging with a carry handle for convenient transportation.

Features:

• Includes strong and durable C49 high-carbon steel sprockets.
• Paired with a high-quality XAM chain.

All Balls Fuel Pump Kits are designed to restore lost performance caused by a failing or non-functioning fuel pump. Each kit offers a plug-and-play solution for quick and easy replacement of your OEM fuel pump module.

Kit contents vary by application and may include components such as the pump, filter, hoses, clamps, and wiring harness. Some kits contain only core components like the pump and filter. Please refer to the product image and listing details for exact contents specific to your model.

Features:

• OEM replacement fuel pump kits.
• Plug-and-play installation.
• Contents vary by kit — check image and listing for details.

This product is an advanced design that lowers operating temperatures for extended longevity and better performance than the OEM part.

Brand new Mosfet Voltage Regulator Rectifier

STOP BURNING YOUR REGULATOR RECTIFIER!
It is time to update or replace your voltage regulator with the advanced MOSFET type.
It runs cooler than all OEM diode-style regulators.

• Direct replacement to your original unit
• Plug-and-play, direct fit, easy installation
• The quality exceeds the OEM equipment
• Higher grade of electric components
• Improved heat sink and charging capabilities
• All shipped products are tested

Dimensions:

• Width: 108mm
• Length: 84mm
• Height: 41mm
• Wires length: 355 mm and 945 mm
• Fixation holes center to center: 81mm

Other specifications:

• Number of plugs: 2
• Number of wires: 7
• Wires Length: 580mm and 600mm
• Minimum Charging Voltage: 14.5 V +/- 0.5 V
• Maximum Charging Current: 50 A / 500 W
• Open Circuit Voltage: < 15 V
• Operation Temperature: -20° to 85°

Carburetor repair kits

• Kits include all of the necessary components to repair a carburetor. ATV models with two carburetors include components to repair two carburetors.
• Kit includes necessary all O-rings, gaskets, jets, needle, mixture screw, float bowl screws, float valve needle and seat. (Needle jet and other pressed in jets are not included in kit.)
• OEM jet sizes are included in the kit. NBR rubber material is used on all O-rings and rubber gaskets NBR has excellent resistance to the ethanol used in today’s fuels.
• Applications that use paper float bowl gaskets are upgraded to High Performance Interface Gasket material.
• Components included in the kits are based off of US models and discretion must be used when attempting to install the kit on a non US model.
• Off road use only.

A high-quality Transaxle Bearing and Seal Kit from All Balls, featuring double-lip seals to keep dirt out. Fit these for peace of mind.

These tapered DAC bearing kits offer great static performance and dynamic load capacity. The high-performance, tapered bearing delivers a 95% static load and 86% load-carrying capabilities, on average, when compared to standard DAC bearings.

Features:

• High contact, double-lip seal with armour shield.
• O-rings feature a sealed ID to provide superior water and dirt exclusion.
• 52100 bearings are hardened and tempered steel for maximum durability.
• Sold individually.

Bolt brand bolts, nuts and washers meet all OEM standards. Designed with precision, each bolt comes in a convenient pack of 10.

All the bearings and seal required to refit a wheel in one convenient package.

Features:

• Premium high-speed bearings feature low drag.
• Double lip seals on both sides to provide superior exclusion of water and dirt
• Improved grease retention.

NOTE: This complete Vertex Gasket Set contains all parts as pictured.

Produced in the U.S.A. with the latest materials and technology in gasket production to Vertex specifications. Vertex gaskets ensure long-lasting performance and leak prevention for your rebuild needs. Vertex's replacement gaskets and seals are available as top-end kits, complete engine kits, or as an oil seal kit.

• One kit containing all of the gaskets, O-rings, and valve seals necessary to rebuild the entire engine and transmission.
• Includes transmission seals.

Please Note:

1. All electrical components must be fitted by a qualified technician.
2. Before fitting electrical components ensure the root cause of the original failure has been addressed.
3. The absence of either of points 1 or 2 above, will void any warranty.

A quality ball Joint kit from All Balls Racing.

• Bearing cup is made from POM-M90 to isolate steel rod from housing.
• Comes with snap ring and cotter pin. Saves you lots over OEM!

Please Note:

1. All electrical components must be fitted by a qualified technician.
2. Before fitting electrical components ensure the root cause of the original failure has been addressed.
3. The absence of either of points 1 or 2 above, will void any warranty.

Quality carburettor rebuild kit from All Balls.

• Kits include all of the necessary components to repair a carburettor. ATV models with two carburettors include components to repair two carburettors.
• Kit includes necessary all O-rings, gaskets, jets, needle, mixture screw, float bowl screws, float valve needles and seat. (Needle jet and other pressed-in jets are not included in the kit.)
• OEM jet sizes are included in the kit. NBR rubber material is used on all O-rings and rubber gaskets NBR has excellent resistance to the ethanol used in today’s fuels.
• Applications that use paper float bowl gaskets are upgraded to High-Performance Interface Gasket material.
• Components included in the kits are based on US models and discretion must be used when attempting to install the kit on a non-US model.
• Off-road use only.

Includes components necessary to complete a piston (top end) rebuild. Competitive pricing, made to meet and exceed OEM quality and designed as a direct OEM replacement.

Features:

• Designed for OEM replacement.
• Made from high-quality materials.
• Meet or exceed OEM specifications.
• Competitive pricing.

The Whites Independent Rear Suspension Knuckle Kit contains everything required to rebuild the rear knuckle on your ATV. The needle bearing shafts are constructed from hardened steel with self-lubricating bushings for excellent wear resistance, all included bushings are hardened and plated for durability and corrosion resistance. IRS Knuckle Kits are model specific, it is recommended that you use our fitments search to ensure correct fit.

Contains everything to rebuild the rear knuckle
Needle bearing shafts are constructed from hardened steel
Self-lubricating bushings for excellent wear resistance
Hardened metal bushings for wear prevention