New Arrivals

RMSTATOR is specialized in designing and manufacturing innovative electrical and electronic components for Powersports vehicles like motorcycles, ATV, SxS, UTV, snowmobiles, and PWC. Through unrelenting quality control, we ensure that each component meets or exceeds the OEM specs. With over 25 product families, rest assured that you will find the part you need.

• Direct replacement to your original unit
• Plug-and-play, direct fit, easy installation
• Highest grade of lamination materials
• Highest grade of copper winding, resistant to 200 degrees Celsius
• Pick up pulsar coil included
• Connectors included
• Rubber grommet included
• Back Plate included
• All products shipped are tested

We have even included the opposite connector (main harness side) as we know these are often melted/corroded/defective and a major cause of repetitive electrical issues.

Dimensions:

• Interior diameter: 29mm
• Exterior diameter: 88mm
• Thickness: 10mm
• Length of wires stator to grommet: 110mm
• Length of wires grommet to plug: 325mm
• Length of pickup coil's wire to grommet: 30mm

Other specifications:

• Number of wires: 3
• Number of plugs: 1
• Number of pins: 3
• Number of poles: 8

Wire to wire resistance:

• Alternator #1: Yellow to White = 0.5 ohms +-20%
• Alternator #2: Yellow to ground = 1 ohms +-20%
• Alternator #3: White to ground = 1.1 ohms +-20%
• Pickup: Blue / Yellow to Ground = 104 ohms +-20%

Please Note:

1. All electrical components must be fitted by a qualified technician.
2. Before fitting electrical components ensure the root cause of the original failure has been addressed.
3. The absence of either of points 1 or 2 above, will void any warranty.

Rough riding calls for stronger axles and that’s where All Balls Racing excels. Machined for exact OEM fit, the shaft is made of chromoly steel with a larger diameter than most axles. The axle has 6 ball bearings in each CV joint. Laminate coating resists corrosion and rust and protects axles from dirt, water, rocks and grease. Waterproof neoprene boots act as a first line of defence, shielding vulnerable joints and preventing leaks. High-performance molybdenum grease reduces heat and friction.

In static torsion trials, these axles were up to 30% stronger than OEM and aftermarket competition.

Features:

• 40% stronger than OEM.
• Larger 4340 chrome-moly steel axle bar.
• Precision ground components.
• Low profile clamps.
• Lasts approximately 50 percent longer than many aftermarket competitors.
• Neoprene boots.
• Typically runs almost 130,000 cycles versus 80,000 cycles for many axles.
• Engineered in the USA.
• Manufactured in an ISO facility.Assembled with 3% molybdenum grease.

Quality replacement Regulator/Rectifiers.

Please Note:

1. All electrical components must be fitted by a qualified technician.
2. Before fitting electrical components ensure the root cause of the original failure has been addressed.
3. The absence of either of points 1 or 2 above, will void any warranty.

Each pack of Premier CSK Clutch Springs contains a complete set of heavy-duty springs. Up to 15% stronger than the original.

Customer should be advised that after installation of a CSK kit the clutch lever will feel slightly ‘heavier’ than standard

Dayco was the first to develop the raw edge sidewall construction V-belt, which facilitated controlled slippage around pulleys.

Timing Belts have been used on camshafts and injection pumps on automotive engines for around 30 years. Dayco® manufactures timing belts for OEMs utilizing the latest technologies in design and materials.

When you're riding, you DON'T want to damage your hearing with the constant roar of the wind whipping under and over your helmet.

You DO however want to hear the things that make for a safe and enjoyable ride... your engine note, vehicles around you, sirens, alarms and the sounds of other people going about their business.

Regular earplugs just block out sound... ALL of it!

Using an ingenious combination of materials and construction, FilterBuds filter out the sounds you DON'T want to hear and filter in the sounds you DO want to hear.

Now available in Commuter 18dB SNR for urban use, Touring 22dB SNR for long- distance use and Race 28dB SNR for high-speed use.

Features:

• Reusable noise-filtering ear plugs.
• Silicone-free, hypoallergenic TPE construction.
• 18dB SNR noise reduction.
• Unique membrane technology.
• Premium metal acoustic mesh.
• Advanced precision filter earplugs.
• Detachable neck cord included.
• Storage canister with key-ring attachment.
• Complies with EN 352-2:2020

Quality carburettor rebuild kit from All Balls.

• Kits include all of the necessary components to repair a carburettor. ATV models with two carburettors include components to repair two carburettors.
• Kit includes necessary all O-rings, gaskets, jets, needle, mixture screw, float bowl screws, float valve needles and seat. (Needle jet and other pressed-in jets are not included in the kit.)
• OEM jet sizes are included in the kit. NBR rubber material is used on all O-rings and rubber gaskets NBR has excellent resistance to the ethanol used in today’s fuels.
• Applications that use paper float bowl gaskets are upgraded to High-Performance Interface Gasket material.
• Components included in the kits are based on US models and discretion must be used when attempting to install the kit on a non-US model.
• Off-road use only.

Oxford Mirror Extenders are perfect for increasing rear visibility while riding, raising the mirror by 51mm further up and 40mm out. Easy to fit, simply unscrew your mirrors, screw the extenders in place, and then screw your mirrors into the extenders.

Key Features
• CNC aluminium construction
• Anodised black
• 2 x M10 x 1.25 right-hand thread
• Bolts included
• 40mm x 51mm extension

Carburetor repair kits
• Kits include all of the necessary components to repair a carburetor. ATV models with two carburetors include components to repair two carburetors.
• Kit includes necessary all O-rings, gaskets, jets, needle, mixture screw, float bowl screws, float valve needle and seat. (Needle jet and other pressed in jets are not included in kit.)
• OEM jet sizes are included in the kit. NBR rubber material is used on all O-rings and rubber gaskets NBR has excellent resistance to the ethanol used in today’s fuels.
• Applications that use paper float bowl gaskets are upgraded to High Performance Interface Gasket material.
• Components included in the kits are based off of US models and discretion must be used when attempting to install the kit on a non US model.
• Off road use only.

The most convenient one-stop-shop for maintaining your motorcycle. Kits include front brake pads/shoes, rear brake pads/shoes, an air filter with 1L of filter oil and an oil filter where applicable.

This kit includes:

GF041S3 - BRAKE PADS GOLDFREN GF041-S3
GF346K5 - BRAKE PADS GOLDFREN GF346-K5
PUTAFBE8144 - PUTOLINE AIR FILTER BE8144
PTAAFO1L - PUTOLINE ACTION AIR FILTER OIL 1LT (70005) *12
MFO631 - MOTO-FILTER OIL FILTER (HF631) SINGLE

HFP replacement fuel pumps, modules, and assemblies are designed to meet or exceed OEM specifications, and feature upgrades that improve on the OEM design. Upgraded polymers, brushes, and commutators ensure long life and durability in multiple fuel blends.

• OEM or better performance
• Polished corrosion-resistant case to help minimize seizing during non-operation
• Specifically designed for quiet operation
• Drop-in replacement
• Gradient density fuel strainer for superior contaminant filtration (intank pumps only)
• Patented check valve technology
• Compatible with modern ethanol-infused pump gasoline

Bolt Engine Fastener Kits come with modern dimpled flange bolts. With a bright zinc finish, these fasteners last long and give a clean, updated look to any engine.

Proudly made in the USA.

• Two-Stroke Engine Fastener kits have all the external fasteners from top to bottom-end, including hardware for: reeds, crankcase, case saver, water pump, left case cover, ignition cover, inner and outer clutch covers, power valve covers.
• Four-Stroke Engine Fastener kits include bottom-end hardware for the following: crankcase covers, clutch cover, oil filter cover, crankcase, case saver, water pump and various top-end bolts depending on model.

Replacement 18-inch Red liner for the Tubliss system

PR SERIES – Off-Road Sintered

Premier PR pads have been upgraded to a new HIGH DENSITY sintered metal compound suitable for all types of moto-x and ATV use.

Brand new aftermarket Voltage Regulator Rectifier

• Direct replacement to your original unit
• Plug-and-play, direct fit, easy installation
• No assembly required
• Higher grade of electric components
• The quality exceeds the OEM equipment
• All products shipped are tested

We have even included the opposite connector (main harness side) as we know these are often melted / corroded / defective and are a major cause of repetitive electrical issues.

Specifications:

Dimensions: p>

• Width: 53 mm
• Length: 70 mm
• Height: 23 mm
• Stator Wire length: 210 mm
• Battery Wire length: 250 mm
• Distance between fixation holes center to center: 55 mm

Other specifications:

• Number of plugs: 2
• Number of pins: 5
• Number of wires: 5
• Minimum Charging Voltage: 14.5 V +- 0.5 V
• Maximum Charging Current: 50 A / 500 W
• Open Circuit Voltage: < 15 V
• Operation Temperature: -20°C to 85°C

Up to 40% stronger than OE axles, these complete axles feature enlarged CV joints, bearing cages, and chromoly axle shafts. All internal components are precision ground and utilize molybdenum grease.

Features:

• 40% stronger than OEM.
• Larger 4340 chrome-moly steel axle bar.
• Precision ground components.
• Low profile clamps.
• Neoprene boots.
• Engineered in the USA.
• Manufactured in an ISO facility.
• Assembled with 3% moly grease.
• Black oxide coating to resist rust and corrosion.

PR SERIES – Off-Road Sintered

Premier PR pads have been upgraded to a new HIGH DENSITY sintered metal compound suitable for all types of moto-x and ATV use.

P SERIES - Street Bikes

Premier's most successful general use material, our P series pads, are a tough Kevlar based organic material giving superb brake effect on all sportbikes and cruisers. This material is preselected by the catalogue when you order P prefix disc pads.

P SERIES - Off-Road

Part numbers relating to off-road machines are supplied in carbon graphite compound for medium durability, good brake effect and minimum heat generation.

Quality design and construction of every All Balls piece meets the toughest standards and conditions - from daily commuting to full-on racing, all older bearing and seal designs are upgraded to the best and latest specs and designs.

Available individually in left-hand and right-hand thread or sold in pairs one L/H and one R/H thread.

The Whites Brake Calipers are designed to withstand harsh and extreme off- road environments and are the perfect cost-effective alternative to replacing your OEM brake calipers.

Including pre-fitted brake pads, mounting bracket, banjo bolt and crush washers, the caliper is ready to install on arrival. Whites Calipers are model and position-specific — we recommend using our fitment finder to find the correct caliper for your model.

Whites Brake Caliper also produces for one of the world's leading and most recognised OEM calliper names. Quality is assured when you buy Whites brand calipers.

Features:

• OEM replacement.
• Built to endure harsh riding environments.
• Includes banjo bolt and two crush washers.
• Includes pre-fitted brake pads.
• Includes mounting bracket and bolts.
• Includes removable brake pins.
• Cost-effective OEM alternative.

Vertex Steel Valves are designed as OEM replacements, precision-forged they are strong & durable. Machined head and seat surfaces provide a precise fit. Vertex valves are nitride coated and induction hardened valve stem tip provide longevity while a precision polished surface reduces friction resulting in less heat build-up. Vertex valves are compatible with all OEM valve keepers and are sold individually allowing you to keep your replacement costs down.

• Forged one-piece OEM replacement valves
• Precision machined valve head and seat surfaces
• Nitride coated
• Induction hardened valve stem tip
• Precision polished surface
• Compatible with OEM valve keepers
• Sold each

Upgrade your motorcycle's clutch system with the All Balls Racing Motorcycle Clutch Cable. Designed with precision and durability in mind, this clutch cable delivers exceptional performance and reliability on the road.

• Black PVC outer jacket for maximum flexibility and durability.
• Steel inner casing that is tightly coiled for low compression.
• A pre-lubricated nylon inner sleeve guarantees smooth operation and long life.
• All wire ends are bird-caged prior to terminal casting for superior pull-out resistance.
• EPDM-moulded rubber components for high UV resistance and long life.
• Injected moulded components are manufactured from high-strength POM material.

REPLACEMENT BOLTS FOR THE OXFORD ROTAFORCE GROUND ANCHOR

Features a black PVC outer jacket for maximum flexibility and durability, steel inner casing that is tightly coiled for low compression, pre-lubricated nylon inner sleeve, bird-caged wire ends, EPDM moulded rubber for high UV resistance and injection moulded components manufactured from high-strength POM material.

Features:

• Flexible and durable with steel inner casing that is tightly coiled for low compression.
• Pre-lubricated nylon inner sleeve.
• Bird caged wire ends.
• EPDM moulded rubber for high UV resistance and injection moulded components made from high-strength POM material.

Note: Kit contents may vary by fitment and are subject to change.