STEERING & SUSPENSION

Rough riding calls for stronger axles and that’s where All Balls Racing excels. Machined for exact OEM fit, the shaft is made of chromoly steel with a larger diameter than most axles. The axle has 6 ball bearings in each CV joint. Laminate coating resists corrosion and rust and protects axles from dirt, water, rocks and grease. Waterproof neoprene boots act as a first line of defence, shielding vulnerable joints and preventing leaks. High-performance molybdenum grease reduces heat and friction.

In static torsion trials, these axles were up to 30% stronger than OEM and aftermarket competition.

Features:

• 40% stronger than OEM.
• Larger 4340 chrome-moly steel axle bar.
• Precision ground components.
• Low profile clamps.
• Lasts approximately 50 percent longer than many aftermarket competitors.
• Neoprene boots.
• Typically runs almost 130,000 cycles versus 80,000 cycles for many axles.
• Engineered in the USA.
• Manufactured in an ISO facility.Assembled with 3% molybdenum grease.

The All Balls CV Boot material is compounded from an OEM grade DCR66 rubber that is formulated specifically for the demanding requirements of today’s ATVs and UTVs.

• 40% higher tensile strength than conventional CV boot material, suitable for the high joint angles of modern ATVs and UTVs.
• 50% more abrasion-resistant than conventional CV boot material to ensure a long life in harsh off-road environments.
• Rubber compound is tested to -40° F to ensure good performance and long life at low temperatures.
• Lithium-based Molybdenum Grease insures good lubrication for long CV joint life. Easier to install than most OEM and aftermarket boots. Sold each. Does not require the use of a ""Banding Tool"".

Specifications:

• Shaft I.D.: 19
• CV Body I.D.: 65
• Length: 85

Kits include:

• Two stainless steel clamps that are designed to be tightened without the use of special tools.

Upgrade rubber bushings found in Utility ATV A-Arms to AB's redesigned HD Delrin bushings.
This kit is designed to replace worn out rubber bushings and provides greater suspension travel and performance.
Quality design and construction of every All Balls piece meets the toughest standards and conditions - from daily commuting to full-on racing, all older bearing and seal designs are upgraded to the best and latest specs and designs.

All Balls Lower Shock Bearing Kit

Kit contains all of the components required to properly rebuild the lower shock bearing assembly.
Needle bearing shafts are made with SCM415/42 bearing steel that has been hardened and precision ground.
All metal bushings are case hardened and plated to prevent wear and corrosion.
POM composite washer bearings replace thruneedle washers fincreased service life and superiresistance to water and dirt.

Rough riding calls for stronger axles and that’s where All Balls Racing excels. Machined for exact OEM fit, the shaft is made of chromoly steel with a larger diameter than most axles. The axle has 6 ball bearings in each CV joint. Laminate coating resists corrosion and rust and protects axles from dirt, water, rocks and grease. Waterproof neoprene boots act as a first line of defence, shielding vulnerable joints and preventing leaks. High-performance molybdenum grease reduces heat and friction.

In static torsion trials, these axles were up to 30% stronger than OEM and aftermarket competition.

Features:

• 40% stronger than OEM.
• Larger 4340 chrome-moly steel axle bar.
• Precision ground components.
• Low profile clamps.
• Lasts approximately 50 percent longer than many aftermarket competitors.
• Neoprene boots.
• Typically runs almost 130,000 cycles versus 80,000 cycles for many axles.
• Engineered in the USA.
• Manufactured in an ISO facility.Assembled with 3% molybdenum grease.

A quality Steering Head Bearing kit from All Balls. Make your bike handle like new!

Features:

• Upgrade ball-type steering bearings to Heavy-Duty Tapered Bearings
• Higher torque load and better wear than OEM ball-style steering bearings.
• Each kit is complete with upper and lower bearing sets and seals.

All Balls now offers a complete fork bush kit solution. The kit includes the following products:

• 2x slider bushings
• 2x leg bushings
• All copper washers and O-rings, 2 fork seal snap rings.

Quality design and construction of every All Balls piece meets the toughest standards and conditions — from daily commuting to full-on racing, all older bearing and seal designs are upgraded to the best and latest specs and designs.

A Quality Fork Bush from All Balls Racing. 

*This is just a single bush

A quality pair of fork oil and dust seals from All Balls Racing.

Features:

• Dyno tested to last 3 to 4 times longer than OEM seals.
• Directional ribs outside of the seal allow easy installation.
• Dual-sealing lips guarantee oil stays in and dirt stays out.

Quality design and construction of every All Balls piece meets the toughest standards and conditions - from daily commuting to full-on racing, all older bearing and seal designs are upgraded to the best and latest specs and designs.

Available individually in left-hand and right-hand thread or sold in pairs one L/H and one R/H thread.

Dynamically balanced to reduce noise and vibration, lengthening its life and the time between re-servicing. All Balls Stealth Drive Prop Shafts include a carrier bearing to reduce cost, ease assembly and provide a complete ready-to-install driveline, out of the box.

Features:

• Phased pairs are balanced and phased as complete, two-piece assemblies.
• Designed with the same dimensions as O.E.M. drive shafts for guaranteed fitment.
• Greaseable U-joints allow maintenance of the drive shaft.

Up to 40% stronger than OE axles, these complete axles feature enlarged CV joints, bearing cages, and chromoly axle shafts. All internal components are precision ground and utilize molybdenum grease.

Features:

• 40% stronger than OEM.
• Larger 4340 chrome-moly steel axle bar.
• Precision ground components.
• Low profile clamps.
• Neoprene boots.
• Engineered in the USA.
• Manufactured in an ISO facility.
• Assembled with 3% moly grease.
• Black oxide coating to resist rust and corrosion.

Designed to keep your differential in top condition, this kit includes high-quality seals that prevent leaks and protect against dirt, water, and debris. Easy to install and compatible with a wide range of ATV and UTV models, this differential seal kit provides a cost-effective solution to prevent costly repairs and downtime. Fit these and have peace of mind.

Features:

• Double lip type TC seals.
• Front or rear position sold separately.

Note: Contains seals only. Verify fitment before purchasing.

A quality Steering Head Bearing kit from All Balls. Make your bike handle like new!

Features:

• Upgrade ball-type steering bearings to Heavy-Duty Tapered Bearings
• Higher torque load and better wear than OEM ball-style steering bearings.
• Each kit is complete with upper and lower bearing sets and seals.

In one box, you'll get all of the bearing and seals you'll need to service your front differential. All Balls manfactures a wide range of high-quality design and construction products that meet the toughest standards and conditions.

KoubaLink specialises in motorcycle lowering and performance linkages for off-road and dual-sport rear suspension systems. Compromise is not an option at KoubaLink. Listening to riders from all over the world explain where and how they use their off-road and dual-sport bikes. With their input, Koubalink manufacture products that add to your motorcycling experience and make it a little more enjoyable.

• Provides better front-end stability by lowering rear suspension geometry
• Machined from billet aluminium
• Stronger than OEM
• Assembled using OE bearings and seals
• Replace linkage like its OEM
• Includes all required bearings and seals for assembly (Excluding Dog Bone styled linkages that do not include bearings and seals from factory)

Lowering amount varies by application:

• KAWASAKI KLX 450 2009 - 38.1mm
• KAWASAKI KX 250F 2017-2020 - 34.925mm
• KAWASAKI KX 250F/XC 2021 - 38.1mm
• KAWASAKI KX 450F 2006-2008 - 41.91mm
• KAWASAKI KX 450F 2009-2011 - 34.925mm
• KAWASAKI KX 450F 2012-2015 - 25.4mm
• KAWASAKI KX 450F 2016-2018 - 19.05mm
• KAWASAKI KX 450F/XC 2019-2021 - 38.1mm

The All Balls Upper Shock Bearing Kit is designed to replace worn-out shock bushings and bearings and give superior suspension compliance.

• Contains the bearing(s) and all of the seals, spacers and pins (if required) to rebuild your shock bearings to factory specifications
• O.E.M.-style cup seal
• Bearings made with hardened and precision-ground 52100 bearing steel
• Note: Kit contents will vary by fitment and are subject to change

A Quality Fork Bush from All Balls Racing. 

*This is just a single bush

Modern bikes are built to withstand extreme conditions, but suspension linkage bearings are often the first to wear out. Constant exposure to dust, mud, and moisture, followed by wet storage, accelerates wear and causes suspension slop. Restore your rear suspension's full performance with a high-quality All Balls Racing swingarm linkage bearing set.

Features:

• Replacement bearing kit for swingarm linkages.
• OEM quality parts at a fraction of the price.
• Kit includes bearings, seals and spacers needed for a full rebuild.

All Balls now offers a complete fork bush kit solution. The kit includes the following products:

• 2x slider bushings
• 2x leg bushings
• All copper washers and O-rings, 2 fork seal snap rings.

Quality design and construction of every All Balls piece meets the toughest standards and conditions — from daily commuting to full-on racing, all older bearing and seal designs are upgraded to the best and latest specs and designs.