All Products

Perfect for a replacement or a performance upgrade of the fuel tap diaphragm.

Features:

• Metal bushings are case-hardened and plated to prevent wear and corrosion.
• Needle bearing shafts are made with SCM415/42 bearing steel that have been hardened and precision ground.

PH SERIES – Street Sport Sintered

High-performance HH friction rated sintered metal pads made in the USA to an exclusive Premier formulation. PH brake pads offer maximum durability and unbeatable performance under heavy braking and high-speed use. PH series is no longer available for off-road applications following the formulation improvements of the PR range for Moto-X and ATV applications.

RMSTATOR is specialized in designing and manufacturing innovative electrical and electronic components for Powersports vehicles like motorcycles, ATV, SxS, UTV, snowmobiles, and PWC. Through unrelenting quality control, we ensure that each component meets or exceeds the OEM specs. With over 25 product families, rest assured that you will find the part you need.

• Direct replacement to your original unit.
• Plug-and-play, direct fit, easy installation.
• No assembly required
• Higher grade of electric components.
• Improved heat sink and charging capabilities
• The quality exceeds the OEM equipment

RM STATOR has even included the opposite connector (main harness side), as they know these are often melted/corroded/defective and a major cause for repetitive electrical issues.

Battery condition is extremely important. No voltage regulator can work correctly with a bad or weak battery. Always fully charge your battery before performing any charging system tests or replacing parts. If there is any doubt, have the battery load tested or replaced.

Please Note:

1. All electrical components must be fitted by a qualified technician.
2. Before fitting electrical components ensure the root cause of the original failure has been addressed.
3. The absence of either of points 1 or 2 above, will void any warranty.

Quality pair of fork oil seals from All Balls Racing.

Features:

• Dyno tested to last 3 to 4 times longer than OEM seals.
• Directional ribs on outside of seal allow seal to be installed easily.
• Dual-sealing lips guarantee oil stays in and dirt stays out.

P SERIES - Street Bikes

Premier's most successful general use material, our P series pads, are a tough Kevlar based organic material giving superb brake effect on all sportbikes and cruisers. This material is preselected by the catalogue when you order P prefix disc pads.

P SERIES - Off-Road

Part numbers relating to off-road machines are supplied in carbon graphite compound for medium durability, good brake effect and minimum heat generation.

RMSTATOR specialises in designing and manufacturing innovative electrical and electronic components for Powersports vehicles like motorcycles, ATV, SxS, UTV, snowmobiles, and PWC. Through unrelenting quality control, we ensure that each component meets or exceeds the OEM specs. With over 25 product families, rest assured that you will find the part you need.

Features:

• Direct replacement to your original unit.
• Plug-and-play, direct fit, easy installation.
• Highest grade of lamination materials.
• Highest grade of copper winding, resistant to 200 degrees Celsius.
• Connector included.

Please Note:

1. Battery condition is extremely important. No stator can work correctly with a bad or weak battery. Always fully charge your battery before performing any charging system tests or replacing parts. If there is any doubt, have the battery load tested or replaced.
2. All electrical components must be fitted by a qualified technician.
3. Before fitting electrical components ensure the root cause of the original failure has been addressed.
4. The absence of either of points 1 or 2 above, will void any warranty.

Essential lock reminder cable - a highly visual cue to stop you riding away with your disc lock still attached.

Attach it to your key ring when not in use - reminds you to lock your bike!

Attach one end to disc lock and the other to your handlebar, it will remind you to remove your lock before riding. The bright-coloured coiled cable acts as a highly visual theft deterrent.

Features:

• 2.5mm? plastic cable.
• Simple to use.
• Lightweight construction.
• 1.2m when stretched.
• Highlights use of lock to thieves.

Replacement mirror suitable for most naked bikes.

• Left Side
• M10 x 1.25 RH thread

GOLDfren began manufacturing sintered disc brake pads for a wide range of off-road and road motorcycles in 1991, nearly three decades on from their first motorcycle brake pads GOLDfren has become one of the largest aftermarket manufacturers in the motorcycle brake disc pad industry. Their development of next-generation products has kept them at the technological forefront of Sintered Friction Braking providing you with confidence in the performance, durability and reliability of your brakes.

S3 Series:

The S3 sintered compound is optimal in dry and wet conditions for road & off-road motorcycles. For the road application, S3 pads are suitable for both the front and rear brake while on off-road applications the S3 is only recommended for the front brake. The S3 series is designed for low abrasive interaction with the rotor and quieter braking due to the ceramic composite material. It has an HH friction rating and performs better at higher temperatures than the AD compound. Friction materials contain metal-ceramic with a bronze-graphite and non-metallic friction additives are spread evenly on the base fine bronze body to achieve optimal friction properties.

Features:

• Very high static friction coefficient
• Minimal difference between wet and dry braking performance
• Good abrasive resistance
• Low abrasive interaction with the brake rotor material
• Longer life compared to organic and Kevlar composite materials

Application:

• For riders who demand a bit more than average from their bikes
• Recommended on both front and rear brakes (road application)
• Can also be used on the front brakes of off-road bikes and ATVs
• Works well on both dry and wet conditions

Operating Parameters:

• Specific pressure: 3.0 Mpa
• Sliding speed: 45 m/s
• Constant maximum temp: 450°C
• Short time maximum temp: 800°C
• Counter-surfaces: steel disks

What is a sintered brake pad?

GOLDfren only manufacturers sintered brake pads that contain metal-ceramic and ceramic-carbon friction materials, these materials allow for less brake dust and a quieter braking experience. Sintered brake pads are made by fusing together metallic particles under high temperature and pressure which enhances friction properties and pad life, resulting in longer life and stronger braking. Sintered brake pads experience no brake fade when operating at high temperatures and in wet conditions. They also last up to 5 times longer than organic pads and provide additional braking strength. All materials used are environmentally friendly and do not contain any lead, asbestos, fibreglass or formaldehyde.

Reminder: one set of brake pads services one brake disc, if you are servicing multiple discs you will need multiple sets of brake pads.

Ceramic Resistors
9 Watt
21.5 Ohm
Sold as Pairs

Wossner is Germany's finest aftermarket forged piston and rod manufacturer and have over 25 years of experience in the high-performance racing industry. Top European racers and FIM World Champions rely on Wossner for only the best pistons, rods, and customer service.

Diameter: 52.50mm

Note: This includes ONE Piston Ring and some fitments may require two rings.

WMP complete range of motocross racing numbers is available in all ten digits and three colour options. In a traditional Impact font with narrow styling to allow room for three-digit race numbers, the Whites Race Numbers are perfect for your ride. A standard 6-inch tall digit allows use on some smaller models and is sold as a packet of 10 to add your prideful number to your ute/van and toolbox.

Features:

• Impact font.
• Narrow style.
• 6-inch tall.
• Packet of 10.
• Available in Numbers 0-9.
• Available in Black, White, or Red.
• Colour: Black

Ideal replacement for dirt bikes.

Features:

• Anti-swell alloy impregnated heavy-duty cork-based facings.
• Smooth clutch take up compared to paper clutches, which can ‘snatch’.
• Steel separator plates increase flywheel effect of the engine and improve performance.

The Torque Mighty 15 Folding Multi-Tool includes 15 chrome vanadium tools. It has laser-etched graphics and lightweight 6061 aluminium sides.

Key Features:

• 2, 2.5, 3, 4, 5, 6, 8mm Hex keys.
  
  
• T25 Torx key.
  
  
• No.2 Cross head screwdriver.
  
  
• No.5 Flat head screwdriver.
  
  
• Chain tool.
  
  
• 14G, 15G, 16G, Mavic M7 spoke keys.

High-quality park hand brake cable from All Balls.

Features:

• Black PVC outer jacket for maximum flexibility and durability.
• Steel inner casing that is tightly coiled for low compression.
• A pre-lubricated nylon inner sleeve guarantees smooth operation and long life.
• All wire ends are bird caged prior to terminal casting for superior pull-out resistance.
• EPDM molded rubber components for high UV resistance and long life.
• Injected molded components are manufactured from high strength POM material.

Kit includes quantities required to replace all OEM seals.

The ultimate in cool kit!

When activated, the indicator dynamically sweeps across from the inside to the outside of the indicator strip.

Features

• Universal Fit
• Waterproof design
• E-mark approved, suitable for road use
• Sequential LED indicators
• Contains 7 LEDs behind a smoked lens, housed in a tough, matt black case
• Voltage 12V Power 2.4W
• M8 bolt - thread pitch 1.25

Size: 103mm (L) x 15mm (W) x 12mm (D)

Includes

• A right and left indicator (for front or rear use)
• 2 resistors to regulate the flash rate

Quality Starter Brushes from J&N Electrical. Replace your worn-out starter motor brushes with these and get your starter motor running again.

Manufactured following strict OE standards to work like the original component.

Features:

• Engineered using the latest technology to ensure the product lasts longer in service.
• Engineered with a factory-like design for effortless installation, ensuring a perfect match with your vehicle.
• Made of high-quality components for durability, reliability, and performance.
• Designed specifically for trucks, trailers, and buses.

Note:

1. All electrical components must be fitted by a qualified technician.
2. Before fitting electrical components ensure the root cause of the original failure has been addressed.
3. The absence of either of points 1 or 2 above, will void any warranty.

Comprehensive kit for transmission rebuild, includes bearings, seals, o-rings, and shims.

• Affordable alternative to OEM replacement parts.
• Utilizes high-quality ABEC 3 precision ball bearings for durability and performance.
• Sourced components, including ball bearings, needle bearings, tapered bearings, PTFE lined bearings, seals, and o-rings, from reputable manufacturers worldwide.
• Kits with tapered bearings come with a selection of shims for customization.

Includes components necessary to complete a piston (top end) rebuild. Competitive pricing, made to meet and exceed OEM quality and designed as a direct OEM replacement.

Features:

• Designed for OEM replacement.
• Made from high-quality materials.
• Meet or exceed OEM specifications.
• Competitive pricing.

A quality caliper rebuild kit from All Balls. Contains everything needed to rebuild your caliper to like new condition.

Founded in 2008, Motobatt is a manufacturer of premium Powersports batteries, battery chargers and battery related accessories. Motobatt is the creator and holds patents all over the world for the Motobatt 4 terminal battery that facilitates flexible battery installation across a wide variety of vehicles while maintaining an OE like fit.

Features:

• Self Sensing Microprocessor
• 3 Step Algorithm
• Fully Automatic Charging & Maintaining
• Overcharge Protection
• Reverse Polarity Protection
• Short Circuit Protection
• Maintains Full Charge

Specifications:

• Application: 6V & 12V AGM, Lead-Acid, Calcium & Gel Batteries
• Input: Auto-switching 120-240VAC 50/60 Hz
• Output: Select 6V/12VDC 500mA
• Max Charge Current: 500mA
• Max Voltage: 7.4V (6V Battery), 14.7V (12V Battery)
• Battery Capacity: 2-20Ah (Charging), up to 50Ah (Maintenance)

Produced in the U.S.A. with the latest materials and technology in seal production to Vertex specifications. Vertex seals ensure long-lasting performance and leak prevention for your rebuild needs.

Features:

• OEM replacement mechanical water pump seal.
• High-quality seal face material seals better and lasts longer.
• Corrosion and chemical-resistant materials keep your engine clean, safe and cool.
• Meets or exceeds OEM quality.

NOTE: This complete Vertex Gasket Set contains all parts as pictured.

Produced in the U.S.A. with the latest materials and technology in gasket production to Vertex specifications. Vertex gaskets ensure long-lasting performance and leak prevention for your rebuild needs. Vertex's replacement gaskets and seals are available as top-end kits, complete engine kits, or as an oil seal kit.

• One kit containing all of the gaskets, O-rings, and valve seals necessary to rebuild the entire engine and transmission.
• Includes transmission seals.

Rack kit contains tie rod end and shaft that connect to the steering rack as well as the outer tie rod end, boot and the required hardware for one side.\

Applications:

• 2020 Polaris Ranger 1000 EPS
• 2020 Polaris Ranger Crew 1000 EPS
• 2020 Polaris Ranger Crew XP 1000 EPS Northstar HVAC Edition
• 2020 Polaris Ranger Crew XP 1000 EPS Texas Edition
• 2019 Polaris Ranger Crew XP 1000 EPS
• 2019 Polaris Ranger Crew XP 1000 EPS Northstar HVAC Edition
• 2018 Polaris Ranger Crew XP 1000 EPS Northstar HVAC Edition
• 2020 Polaris Ranger XP 1000 EPS Northstar HVAC Edition
• 2020 Polaris Ranger XP 1000 EPS Texas Edition