ELECTRICAL

Each bike manufacturer uses different connectors for their indicators. This means that when fitting universal aftermarket indicators you need to cut the original connectors off and replace them with bullet fittings.

Not any more! Simply connect the IndyLeads between the original connector and the universal connector. Simple.

2 pack for front OR rear.

It is time to update or replace your voltage regulator with the advanced MOSFET type.

It runs cooler than all OEM diode-style regulators. In addition, this rectifier has overheat protection, rather than burn up it will simply turn off for a while and cool off.

• Direct replacement to your original unit
• Plug-and-play, direct fit, easy installation
• The quality exceeds the OEM equipment
• Improved heat sink and charging capabilities
• Higher-grade of electric components
• All shipped products are tested

Specifications:

• Dimensions:

  • Width: 86mm
  • Length: 125mm
  • Height: 42mm
  • Fixation holes center to center: 128mm

• Other Specifications:

  • Number of plugs: 2
  • Number of pins: 5

The failure-prone harnesses on BMWs are known to develop corrosion, which increases electrical resistance. This, in turn, raises the temperature of wires to the point where connectors start melting. When this happens, the voltage regulator (and most likely the stator) fails, leading to steep repair expenses.

RMStator's new bypass voltage regulator brings back the renowned RMSTATOR Series technology, designed to bypass the main wiring harness and connect the voltage regulator directly to the battery. This configuration has demonstrated a major increase in voltage regulator reliability in real-life scenarios over the years.

Features:

• Series Technology: Significantly lowers regulator and stator temperatures for more accurate voltage regulation, increasing the reliability of your charging system components.
• PRO-FIT System: Includes everything required for an RMSTATOR-style professional installation: part connectors, bypass harness, and dielectric connector grease.
• Power only flows through the electrical components when the battery is charging.
• Allows the stator to have lower current flowing when not in use, extending its lifetime.
• The regulator is easier to mount because it is smaller than the OEM.

Specifications:

Series Regulator

Dimensions:

• Width: 84 mm
• Length: 90 mm
• Height: 32 mm
• Fixation holes center to center: 69 mm

Other Specifications:

• Number of plugs: 2
• Number of pins: 5
• Minimum Charging Voltage: 14.5 V ± 0.5 V
• Maximum Charging Current: 50 A / 500 W
• Open Circuit Voltage: < 15 V
• Operating Temperature: -20°C to 85°C

Bypass Harness

Dimensions:

• Stator wires length: 500 mm
• Battery wires length: 1000 mm

Other Specifications:

• Number of yellow wires: 3
• Number of red wires: 1
• Number of black wires: 1
• Number of plugs: 3

Each bike manufacturer uses different connectors for their indicators. This means that when fitting universal aftermarket indicators you need to cut the original connectors off and replace them with bullet fittings.

Not any more! Simply connect the IndyLeads between the original connector and the universal connector. Simple.

2 pack for front OR rear.

Unleash the full potential of your Honda with Whites Switch Stop Engine/Map Button. Fine-tune your engine's performance for optimal power delivery and fuel efficiency with just a push of a button.

Please Note:

1. All electrical components must be fitted by a qualified technician.
2. Before fitting electrical components ensure the root cause of the original failure has been addressed.
3. The absence of either of points 1 or 2 above, will void any warranty.

• Direct replacement to your original unit
• Plug-and-play, direct fit, easy installation
• All products shipped are tested

RMSTATOR is specialized in designing and manufacturing innovative electrical and electronic components for Powersports vehicles like motorcycles, ATV, SxS, UTV, snowmobiles, and PWC. Through unrelenting quality control, we ensure that each component meets or exceeds the OEM specs. With over 25 product families, rest assured that you will find the part you need.

• Direct replacement to your original unit
• Plug-and-play, direct fit, easy installation
• Highest grade of lamination materials
• Highest grade of copper winding, resistant to 200 degrees Celsius
• Connector included

Battery condition is extremely important. No stator can work correctly with a bad or weak battery. Always fully charge your battery before performing any charging system tests or replacing parts. If there is any doubt, have the battery load tested or replaced.

Please Note:

1. All electrical components must be fitted by a qualified technician.
2. Before fitting electrical components ensure the root cause of the original failure has been addressed.
3. The absence of either of points 1 or 2 above, will void any warranty.

Quality replacement Starter Relay

Please Note:

1. All electrical components must be fitted by a qualified technician.
2. Before fitting electrical components ensure the root cause of the original failure has been addressed.
3. The absence of either of points 1 or 2 above, will void any warranty.

Please Note:

1. All electrical components must be fitted by a qualified technician.
2. Before fitting electrical components ensure the root cause of the original failure has been addressed.
3. The absence of either of points 1 or 2 above, will void any warranty.

Please Note:

1. All electrical components must be fitted by a qualified technician.
2. Before fitting electrical components ensure the root cause of the original failure has been addressed.
3. The absence of either of points 1 or 2 above, will void any warranty.

Motorcycles, especially higher-powered motorcycles, sometimes have trouble starting, especially in cold weather. The perfect solution for this is to replace the starter motor with a high-quality J&N Electrical motor for a quick start every time.

Features:

• Meets or exceeds OEM specification.
• 100% interchangeable, no modifications required.
• Durable double-sealed case for longer life.
• Vigorously tested and manufactured with insulated fittings.
• Provides higher torque than many OEM starter motors.

Please Note:

1. All electrical components must be fitted by a qualified technician.
2. Before fitting electrical components ensure the root cause of the original failure has been addressed.
3. The absence of either of points 1 or 2 above, will void any warranty.

Brand new aftermarket stator

• Direct replacement to your original unit
• Plug-and-play, direct fit, easy installation
• Highest-grade lamination materials
• Highest-grade copper windings, resistant to 200 degrees Celsius.
• Pick up pulsar coil included
• Connector included
• Rubber grommet included
• All products shipped are tested

Specifications:

Dimensions :

• Interior diameter: 29 mm
• Exterior diameter: 88 mm
• Thickness: 10 mm
• Length of wires stator to grommet: 110 mm
• Length of wires grommet to plug: 475, 100 mm
• Length of pickup coil's wire to grommet: 145 mm

Other specifications :

• Number of wires: 4
• Number of plugs: 2
• Number of holes: 2
• Number of poles: 8
• Alternator : White to Ground = 1.1 ohms +-20%
• Pickup: Blue/yellow to Ground = 119 ohms +-20%

Please Note:

1. All electrical components must be fitted by a qualified technician.
2. Before fitting electrical components ensure the root cause of the original failure has been addressed.
3. The absence of either of points 1 or 2 above, will void any warranty.

Direct replacement to your original unit. Plug-and-play, direct fit, easy installation.

Specifications:

• Dimensions:

  • Width: 17.5 mm
  • Length: 45 mm
  • Height: 45 mm

• Other Specifications:

  • Number of plugs: 1
  • Number of terminals: 3
  • Resistance: 1000 ohms ± 10%

Please Note:

1. All electrical components must be fitted by a qualified technician.
2. Before fitting electrical components ensure the root cause of the original failure has been addressed.
3. The absence of either of points 1 or 2 above, will void any warranty.

A multi-functional indicator with running lights. When activated, the indicator dynamically sweeps across from the inside to the outside of the indicator strip.

Features
• Universal Fit
• Waterproof design
• E-mark approved, suitable for road use
• 2-in-1 LED sequential indicators with running lights
• Contains 14 LEDs housed in a tough, matt black case
• 7 LEDs for the running lights
• 7 LEDs for the indicators
• Voltage 12V Power 2W
• M8 bolt - thread pitch 1.25
• Size: 111mm (L) x 15mm (W) x 14.5mm (D)

Includes
• A right and left indicator for front use
• 2 resistors to regulate the flash rate

Please Note:

1. All electrical components must be fitted by a qualified technician.
2. Before fitting electrical components ensure the root cause of the original failure has been addressed.
3. The absence of either of points 1 or 2 above, will void any warranty.

Please Note:

1. All electrical components must be fitted by a qualified technician.
2. Before fitting electrical components ensure the root cause of the original failure has been addressed.
3. The absence of either of points 1 or 2 above, will void any warranty.

Please Note:

1. All electrical components must be fitted by a qualified technician.
2. Before fitting electrical components ensure the root cause of the original failure has been addressed.
3. The absence of either of points 1 or 2 above, will void any warranty.

Put the spark back in your ride with a Whites Electrical Coil. Manufactured as a direct OEM replacement while meeting or exceeding OEM specifications, it will mount with ease and outperform that worn out coil. Whites Ignition Coil's are the perfect cost-effective alternative to OEM ignition coils, with a vast range of applications available.

Features:

• Cost-effective OEM alternative.
• OEM replacement.
• Manufactured to meet or exceed OEM specifications.
• Diverse applications.
• Voltage: 12V
• Primary (ohm): 0.6 ohm
• Secondary (ohm): 5.97k ohm
• Holes Centres: 55mm

Please Note:

1. All electrical components must be fitted by a qualified technician.
2. Before fitting electrical components ensure the root cause of the original failure has been addressed.
3. The absence of either of points 1 or 2 above, will void any warranty.

Produced in the U.S.A. with the latest materials and technology in gasket production to Vertex specifications. Vertex gaskets ensure long-lasting performance and leak prevention for your rebuild needs.

• Ignition cover gasket
• Designed to fit O.E.M. cover

DENALI Motorcycle Specific Horn Mounts

Available for many ADV, Cruisers and Sport Touring Models. The laser cut and powder coated steel brackets mount our SoundBomb Horn inthe most discrete and attractive location possible.

Each bike manufacturer uses different connectors for their indicators. This means that when fitting universal aftermarket indicators you need to cut the original connectors off and replace them with bullet fittings.

Not any more! Simply connect the IndyLeads between the original connector and the universal connector. Simple.

2 pack for front OR rear.

Brand new aftermarket Stator + Mosfet Regulator Kit

• Direct replacement to your original unit
• Plug-and-play, direct fit, easy installation
• All shipped products are tested

*All item pictures are accurate, if in doubt, do not hesitate and compare our item to your original part.

Brand new aftermarket Stator

• Highest grade of lamination materials
• Highest grade of copper winding, resistant to 200 degrees Celsius
• Connectors included
• Rubber grommet included

Brand new Mosfet Voltage Regulator Rectifier

STOP BURNING YOUR REGULATOR RECTIFIER!

It is time to update or replace your voltage regulator with the advanced MOSFET type. It runs cooler than all OEM diode-style regulators. In addition, this rectifier has to overheat protection, rather than burn up it will simply turn off for a while and cool off.

• The quality exceeds the OEM equipment
• Improved heat sink and charging capabilities
• Higher grade of electric components

We have even included the opposite connector (main harness side) as we know these are often melted/corroded/defective and a major cause for repetitive electrical issues.

Please Note: There are 2 possible stators for the Triumph Speed Triple 1050 2005-2010, compare the dimensions of your original product with the dimensions of our product before buying. This stator will fit engine serial number 356143 and up. The other possible product is RM01391S.

STATOR

Dimensions:

• Interi or diameter: 42mm
• Exterior diameter: 115mm
• Thickness: 22mm
• Length of wires stator to grommet: 110mm
• Length of wires grommet to plug: 600mm

Other Specifications:

• Number of wires: 3
• Number of plugs: 1
• Number of pins: 3
• Number of poles: 18

Wire to wire resistance:

• Alternator 3p: Between each Black = 0.5 ohms +-20%

REGULATOR

Dimensions:

• Width: 90mm
• Length: 94mm
• Height: 30mm
• Wires length: 320mm & 235mm
• Fixation holes centre to centre: 75mm

Other Specifications:

• Number of plugs: 2
• Number of pins: 7
• Number of wires: 7
• Minimum Charging Voltage: 14.5 V +- 0.5 V
• Maximum Charging Current: 50 A / 500 W
• Open Circuit Voltage: < 15 V
• Operation Temperature: -20° to 85°

Please Note:

1. All electrical components must be fitted by a qualified technician.
2. Before fitting electrical components ensure the root cause of the original failure has been addressed.
3. The absence of either of points 1 or 2 above, will void any warranty.
4. There are 2 possible stators for the model's Triumph Speed Triple 1050 2005-2010, compare the dimensions of your original product with the dimensions of our product before buying. This stator will fit engine serial number 356143 and up. The other possible product is the RM01391S.

RMSTATOR is specialized in designing and manufacturing innovative electrical and electronic components for Powersports vehicles like motorcycles, ATV, SxS, UTV, snowmobiles, and PWC. Through unrelenting quality control, we ensure that each component meets or exceeds the OEM specs. With over 25 product families, rest assured that you will find the part you need.

• Direct replacement to your original unit.
• Quality exceeds OEM equipment
• 1 Cap coil included
• All shipped products are tested

With certain motorcycle models, the spark plug caps and coils are combined to reduce the number of parts used in order to improve efficiency. However, when the spark plug cap wears out, the cost of the replacement becomes more expensive. If you are experiencing ignition problems, this could mean the ignition cap coil needs to be replaced. Simple, easy to install, affordable, and improves engine performance.

Dimensions:

• Internal tube diameter: 9mm
• Length: 142mm
• Middle diameter: 22.25mm
• Outside diameter: 16.65mm
• Inside depth: 45.6mm
• Seal: 29.85mm

Other specifications:

• Number of terminals: 2

Please Note:

1. All electrical components must be fitted by a qualified technician.
2. Before fitting electrical components ensure the root cause of the original failure has been addressed.
3. The absence of either of points 1 or 2 above, will void any warranty.

Replacement ignition key switch for your motorcycle/ATV. Direct replacement to the original unit this unit provides excellent plug-and-play, direct fit functionality providing a simple, quick & easy installation. Two keys & all connectors are included.

• Direct replacement to your original unit
• Plug-and-play, direct fit, easy installation.
• Two keys included
• Connector included

Dimensions:

• Height : 42mm
• Diameter: 25mm
• Wires length: 630mm

Other Specification:

• Number of wires: 4
• Number of terminals: 4
• Number of plugs: 1
• Number of keys: 2
• Number of positions: 2 (off, on)

Please Note:

1. All electrical components must be fitted by a qualified technician.
2. Before fitting electrical components ensure the root cause of the original failure has been addressed.
3. The absence of either of points 1 or 2 above, will void any warranty.