ELECTRICAL

DENALI Motorcycle Specific Fairing / Fender Mounts

Available for most ADV, Cruisers and Sport Touring Models Laser cut and powder coated steel brackets either position the lights in the optimum location just below to the outside of the headlight, or create a two-point fender mount strong enough to mount our largest lights to your fender.

NEW WIRE HARNESS BYPASS DESIGN

The failure-prone harnesses on Triumphs are known to develop corrosion which increases electrical resistance, which in turn, increases the temperature of wires to the point where connectors start melting. When this happen, the voltage regulator (and most likely the stator) is failing incurring steep repair expenses.

Our new bypass voltage regulator brings back the renowned RMSTATOR Mosfet technology with the RMSTATOR machined aluminum case in a new configuration designed to bypass the main wiring harness and connect the voltage regulator directly to the battery. This configuration has demonstrated a major increase in voltage regulator reliability in real life scenarios over the years.

Features:

Mosfet circuit
Significantly lowers the operating temperature for an increased voltage regulator lifespan. Provide a steadier and smoother signal to the battery.

Billet aluminum housing
Runs 33% cooler than standard cast voltage regulator housings.

PRO-FIT System
Includes everything required to perform a RMSTATOR-style professional installation: part connectors, harness-side connectors and dielectric connector grease.

2-Year Warranty
Covered with a 2-year warranty for a complete peace of mind

Dimensions:

Width: 95 mm
Length: 90 mm
Height: 30 mm
Wires length: 811 mm and 350 mm
Fixation holes centre to centre: 75 mm

Other specifications:

Number of plugs: 2
Number of pins: 5
Number of wires: 5
Minimum Charging Voltage: 14.5 V +/- 0.5 V
Maximum Charging Current: 50 A / 500 W
Open Circuit Voltage: < 15 V
Operation Temperature: -20° C to 85°C

BENEFITS OF SERIES VOLTAGE REGULATORS

SERIES regulators run much cooler than the Shunt and MOSFET voltage regulator rectifier and way much cooler than OEM parts.

This series voltage regulator is an aftermarket replacement to the renowned SH847 voltage regulator.

Power only flows through the electrical components when the battery is charging.

Allows the stator to have lower current flowing when not used, extending its lifetime.

The regulator is easier to mount because it is smaller than the OEM one.

ABOUT THE SERIES VOLTAGE REGULATION TECHNOLOGY

RMSTATOR’s new SERIES voltage regulator brings better reliability and charging system performance. A SERIES regulator is a significant upgrade over typical shunt type voltage regulators.

A shunt regulator controls battery voltage by grounding the stator coils to dissipate current as heat, rather than sending it on to the battery. SERIES regulators control battery voltage by intermittently disconnecting stator coils from the regulator electronics, limiting current flow through the unit and on to the battery completely.

This results in lower regulator and stator temperatures, more accurate voltage regulation, and increased reliability of your charging system components.

INSTALL LIKE A PRO

We include the opposite connector (main harness side) as we know these are often melted/corroded/defective. Defective connectors are a major cause for repetitive electrical issues.

Specifications:

Dimensions:

Width: 119 mm
Length: 100 mm
Height: 38 mm
Fixation holes centre to centre: 100 mm

Other specifications:

Number of plugs: 2
Number of pins: 5
Minimum Charging Voltage: 14.5 V +/- 0.5 V
Maximum Charging Current: 50 A / 500 W
Open Circuit Voltage: < 15 V
Operation Temperature: -20°C to 85°C

Please Note:

1. All electrical components must be fitted by a qualified technician.
2. Before fitting electrical components ensure the root cause of the original failure has been addressed.
3. The absence of either of points 1 or 2 above, will void any warranty.

Please Note:

1. All electrical components must be fitted by a qualified technician.
2. Before fitting electrical components ensure the root cause of the original failure has been addressed.
3. The absence of either of points 1 or 2 above, will void any warranty.

Please Note:

1. All electrical components must be fitted by a qualified technician.
2. Before fitting electrical components ensure the root cause of the original failure has been addressed.
3. The absence of either of points 1 or 2 above, will void any warranty.

Brand new High-Performance aftermarket CDI box.

Features:

• Our PeakRPM technology provides a mor aggressive timing curve for increased throttle response.
• Ride at full throttle with our application-specific CDI box that raises the rev limiter by 1000 RPM.
• Enjoy fast and easy installation with our plug and play desig and included dielectric connector grease.
• OEM-grade electronic components and printed circuit boards for long-term reliability and performance.
• 90% of ignition issues are caused by a faulty stator. Full test ignition components before buying.

Dimensions:

• Height: 27mm
• Length: 96mm
• Width: 87mm
• Fixation holes centre to centre: 70mm

Other specifications:

• Number of plugs: 1
• Number of pins: 8

Note:

1. T only real way to test your CDI box is to swap it out with another known good unit from the same year/make/model. Because of this, we recommend that you rule everything else out before replacing the CDI box.
2. All electrical components must be fitted by a qualified technician.
3. Before fitting electrical components ensure the root cause of the original failure has been addressed.
4. The absence of either of points 1 or 2 above, will void any warranty.

RMSTATOR is specialized in designing and manufacturing innovative electrical and electronic components for Powersports vehicles like motorcycles, ATV, SxS, UTV, snowmobiles, and PWC. Through unrelenting quality control, we ensure that each component meets or exceeds the OEM specs. With over 25 product families, rest assured that you will find the part you need.

• Direct replacement to your original unit
• Plug-and-play, direct fit, easy installation
• Highest grade of lamination materials
• Highest grade of copper winding, resistant to 200 degrees Celsius
• Connector included

Battery condition is extremely important. No stator can work correctly with a bad or weak battery. Always fully charge your battery before performing any charging system tests or replacing parts. If there is any doubt, have the battery load tested or replaced.

Please Note:

1. All electrical components must be fitted by a qualified technician.
2. Before fitting electrical components ensure the root cause of the original failure has been addressed.
3. The absence of either of points 1 or 2 above, will void any warranty.

RMSTATOR is specialized in designing and manufacturing innovative electrical and electronic components for Powersports vehicles like motorcycles, ATV, SxS, UTV, snowmobiles, and PWC. Through unrelenting quality control, we ensure that each component meets or exceeds the OEM specs. With over 25 product families, rest assured that you will find the part you need.

• Direct replacement to your original unit
• Plug-and-play, direct fit, easy installation
• Highest grade of lamination materials
• Highest grade of copper winding, resistant to 200 degrees Celsius
• Connector included

Battery condition is extremely important. No stator can work correctly with a bad or weak battery. Always fully charge your battery before performing any charging system tests or replacing parts. If there is any doubt, have the battery load tested or replaced.

Please Note:

1. All electrical components must be fitted by a qualified technician.
2. Before fitting electrical components ensure the root cause of the original failure has been addressed.
3. The absence of either of points 1 or 2 above, will void any warranty.

Whites lighting range is a collection of high-quality indicators (flashers), tail lamps, headlights and more. Available as direct OEM replacements and universal fitments for those one-off custom rides. Offered in a range of shapes, sizes, styles and mounting options Whites are here for your motorcycle lighting solutions.

Constructed to meet and exceed OEM specifications this flasher by Whites is the perfect fit for your ride. Designed to give bright and clear light for optimal signalling. Replace your damaged or broken OEM flasher with the Whites Flasher for a fraction of the price. Built to match OEM style and mounting, you can install your new flasher with ease while utilising your OEM mounting hardware.

Features:

• Meets and exceed OEM specifications.
• OEM replacement part.
• Utilises OEM mounting hardware.
• Durable construction.
• Fitment Location: Left and Right Front and Rear.
• Colour: Chrome
• Light Type: Bulb

Boasting a sleek black and slim design, the Whites Headlight Switch Block is a multi-purpose handlebar switch with a High, Low and Off setting for your headlight and a kill switch. The switch block is pre-wired with an 18" length and bullet terminals for a quick and easy installation and is compatible with 7/8" handlebars. The block is only 20mm wide and 42mm high making it the perfect replacement for that bulky OEM block on your daily commuter or one of the custom machines.

Features:

• Pre-wired 18" wire with bullet terminals.
• Compatible with 7/8" handlebars.
• Full wrap around design.
• Three stage headlight switch high/low/off.
• Includes kill switch.
• Voltage Range - 11v - 15v
• Max Amps - 2.5 amps
• Material: ABS Plastic
• Width: 20mm
• Height: 42mm

Wiring Configuration:

• Red: Positive
• Black: Earth
• White: Kill Switch
• Green: Low Beam
• Yellow: High Beam
• Blue: Parking Light

With certain BMW motorcycle models, the spark plug caps and coils are combined to reduce the number of parts used in order to improve efficiency. However, when the spark plug cap wears out, the cost of the replacement becomes more expensive. If you are experiencing ignition problems, this could mean the ignition cap coil needs to be replaced. Simple, easy to install, affordable, and improves engine performance.

Features:

• Direct replacement to your original unit.
• Quality exceeds the OEM equipment.
• All products shipped are tested.

Dimensions:

• Interna l tube diameter: 8 mm
• Length: 120 mm
• Seal: 41 x 39 mm
• Number of plugs: 1
• Number of terminals: 3

Notes: All item pictures are accurate, if in doubt, do not hesitate and compare our item to your original part.

RMSTATOR specialises in designing and manufacturing innovative electrical and electronic components for Powersports vehicles like motorcycles, ATV, SxS, UTV, snowmobiles, and PWC. Through unrelenting quality control, we ensure that each component meets or exceeds the OEM specs. With over 25 product families, rest assured that you will find the part you need.

Features:

• Direct replacement to your original unit.
• Plug-and-play, direct fit, easy installation.

Please Note:

1. All electrical components must be fitted by a qualified technician.
2. Before fitting electrical components ensure the root cause of the original failure has been addressed.
3. The absence of either of points 1 or 2 above, will void any warranty.

Put the spark back in your ride with a Whites Electrical Coil. Manufactured as a direct OEM replacement while meeting or exceeding OEM specifications, it will mount with ease and outperform that worn out coil. Whites Ignition Coil's are the perfect cost-effective alternative to OEM ignition coils, with a vast range of applications available.

Features:

• Cost-effective OEM alternative.
• OEM replacement.
• Manufactured to meet or exceed OEM specifications.
• Diverse applications.
• Voltage: 12V
• Primary (ohm): 5.28 ohm
• Secondary (ohm): 18.7k ohm
• Holes Centres: 100mm

Please Note:

1. All electrical components must be fitted by a qualified technician.
2. Before fitting electrical components ensure the root cause of the original failure has been addressed.
3. The absence of either of points 1 or 2 above, will void any warranty.

DENALI Motorcycle Specific Horn Mounts

Available for many ADV, Cruisers and Sport Touring Models. The laser cut and powder coated steel brackets mount our SoundBomb Horn inthe most discrete and attractive location possible.

This vehicle-specific driving light mount allows you to mount any DENALI driving light in the optimum location on your motorcycle. This kit includes sturdy anodised aluminium clamps and beefy powder-coated steel brackets with an M8 mounting hole and all necessary mounting hardware.

Vehicle Fitment

• KTM 790 Adventure 2019-2020
• KTM 790 Adventure R 2019-2020
• KTM 790 Aventure R Rally 2020-2020

Whites Kill Switches are high-quality OEM styled replacement kill switches. Including the bar mount and bolt, wire it up and you're ready to rip. The fully waterproof button and heavy duty covered wire prevents water entering and shorting the switch. OEM style, shape and plug ensures a quick and easy installation.

Features:

• OEM replacement.
• Quick and easy installation.
• Fully waterproof.
• OEM style, shape and plug.

If your ATV won't start and you have diagnosed the issue to be the start solenoid, don't worry! Whites will have your ATV back up and running with minimal damage to the wallet. The Whites Starter Solenoid is a high-quality solenoid with high cranking power that ensures a quick start for your ATV.

Features:

• An affordable alternative to OEM parts
• Meets and exceeds OEM specifications
• Quick and easy installation
• High cranking power

Please Note:

1. This part may not be an exact OEM replacement, and some knowledge of electrical wiring may be required for installation.
2. All electrical components must be fitted by a qualified technician.
3. Before fitting electrical components ensure the root cause of the original failure has been addressed.
4. The absence of either of points 1 or 2 above, will void any warranty.

Quality replacement Starter Motors

Note: Brush kid AHSMU9114 will fit this starter motor.

Please Note:

1. All electrical components must be fitted by a qualified technician.
2. Before fitting electrical components ensure the root cause of the original failure has been addressed.
3. The absence of either of points 1 or 2 above, will void any warranty.

Please Note:

1. All electrical components must be fitted by a qualified technician.
2. Before fitting electrical components ensure the root cause of the original failure has been addressed.
3. The absence of either of points 1 or 2 above, will void any warranty.

Whites Kill Switches are high-quality OEM styled replacement kill switches. Including the bar mount and bolt, wire it up and you're ready to rip. The fully waterproof button and heavy-duty covered wire prevent water from entering and shorting the switch. OEM style, shape and plug ensures a quick and easy installation.

Features:

• OEM replacement.
• Quick and easy installation.
• Fully waterproof.
• OEM style, shape and plug.

Whites Tail Light Assemblies provide a cost-effective option when needed for your ATV or UTV.

Features:

• Available to suit many popular makes, models, and years.
• Direct "bolt-in" replacement; no modification required.

Note: Whites ATV and UTV replacement taillights are designed for off-highway applications only. The lenses on these taillights do not have E-marks, which are required for road vehicle compliance.

SMARTER, BRIGHTER, MORE VERSATILE

Why Denali?

• Our LED light kits are purpose-built for motorcycles, with compact pods delivering unmatched output for their size.
• We lab test every light we engineer to fine-tune our optic and reflector designs, to ensure we're unleashing the full potential of each LED.
• We also go to great lengths to develop bike-specific mounts and wiring adapters, so you can spend less time in the garage and more time on the road.

A faulty air temperature or pressure sensor can cause rough idling, reduced power, poor fuel economy, and increased emissions. Meanwhile, inaccurate readings can hide overheating issues, light a check engine light or even put your machine in limp mode, all putting your engine at risk of severe damage.

Replacing faulty sensor restores reliable performance monitoring, ensuring your machine runs safely and efficiently under all riding conditions.

The TTO Digital Temperature Gauge allows you to easily monitor your engine's temperature ensuring you that your engine is not overheating.

Features:

• Easy to read LCD display and an ultra-thin design.
• The LCD display lets you to easily view all gauge readings regardless of the angle or lighting conditions.
• Surface mount for easy install, comes with double sided VHB tape or can be bolted on
• -40°-300°C/575°F
• Black case, orange version sold separate

What's in the box:

• TTO Temperature
• Screw Caps and VHB Tape
• Temperature Sensor, 1/8th x 28 BSPP, fits thermostat

Replacement ignition key switch for your motorcycle/ATV. Direct replacement to the original unit this unit provides excellent plug-and-play, direct fit functionality providing simple, quick & easy installation. Two keys & all connectors are included.

• Direct replacement to your original unit
• Plug-and-play, direct fit, easy installation.
• Two keys included
• Connector included

Dimensions:

• Height : 45mm
• Length: 34mm
• Width: 35mm

Other Specification:

• Number of wires: 2
• Number of plugs: 2
• Number of keys: 2
• Number of positions: 2 (Off/On)

Brand new aftermarket Voltage Regulator Rectifier

• Direct replacement to your original unit
• Plug-and-play, direct fit, easy installation
• No assembly required
• Higher-grade of electric components
• The quality exceeds the OEM equipment
• All products shipped are tested

We have even included the opposite connector (main harness side) as we know these are often melted / corroded / defective and are a major cause of repetitive electrical issues.

Specifications:

Dimensions: p>

• Width: 81 mm
• Length: 78 mm
• Height #1: 20 mm
• Height #2: 32 mm
• Distance between fixation holes center to center: 67 mm

Other specifications:

• Number of plugs: 1
• Number of pins: 6
• Minimum Charging Voltage: 14.5 V +- 0.5 V
• Maximum Charging Current: 50 A / 500 W
• Open Circuit Voltage: < 15 V
• Operation Temperature: -20°C to 85°C

Please Note:

1. All electrical components must be fitted by a qualified technician.
2. Before fitting electrical components ensure the root cause of the original failure has been addressed.
3. The absence of either of points 1 or 2 above, will void any warranty.