HARD PARTS

Designed to keep your differential in top condition, this kit includes high-quality seals that prevent leaks and protect against dirt, water, and debris. Easy to install and compatible with a wide range of ATV and UTV models, this differential seal kit provides a cost-effective solution to prevent costly repairs and downtime. Fit these and have peace of mind.

Features:

• Double lip type TC seals.
• Front or rear position sold separately.

Note: Contains seals only. Verify fitment before purchasing.

All Balls Fuel Pump Kits are designed to restore lost performance caused by a failing or non-functioning fuel pump. Each kit offers a plug-and-play solution for quick and easy replacement of your OEM fuel pump module.

Kit contents vary by application and may include components such as the pump, filter, hoses, clamps, and wiring harness. Some kits contain only core components like the pump and filter. Please refer to the product image and listing details for exact contents specific to your model.

Features:

• OEM replacement fuel pump kits.
• Plug-and-play installation.
• Contents vary by kit — check image and listing for details.

NOTE: This complete Vertex Gasket Set contains all parts as pictured.

Produced in the U.S.A. with the latest materials and technology in gasket production to Vertex specifications. Vertex gaskets ensure long-lasting performance and leak prevention for your rebuild needs. Vertex's replacement gaskets and seals are available as top-end kits, complete engine kits, or as an oil seal kit.

• One kit containing all of the gaskets, O-rings, and valve seals necessary to rebuild the entire engine and transmission.
• Includes transmission seals.

Please Note:

1. All electrical components must be fitted by a qualified technician.
2. Before fitting electrical components ensure the root cause of the original failure has been addressed.
3. The absence of either of points 1 or 2 above, will void any warranty.

High-quality park hand brake cable from All Balls.

Features:

• Black PVC outer jacket for maximum flexibility and durability.
• Steel inner casing that is tightly coiled for low compression.
• A pre-lubricated nylon inner sleeve guarantees smooth operation and long life.
• All wire ends are bird caged prior to terminal casting for superior pull-out resistance.
• EPDM molded rubber components for high UV resistance and long life.
• Injected molded components are manufactured from high strength POM material.

NOTE: This Vertex Top End Gasket Set contains all components pictured.

Produced in the U.S.A. with the latest materials and technology in gasket production to Vertex specifications. Vertex gaskets ensure long-lasting performance and leak prevention for your rebuild needs. Vertex's replacement gaskets and seals are available as top-end kits, complete engine kits, or as an oil seal kit.

• These sets include the head, base, and exhaust gaskets, valve seals, O-rings and other gaskets to complete a top-end rebuild.

Quality replacement Regulator/Rectifiers.

Please Note:

1. All electrical components must be fitted by a qualified technician.
2. Before fitting electrical components ensure the root cause of the original failure has been addressed.
3. The absence of either of points 1 or 2 above, will void any warranty.

Features a black PVC outer jacket for maximum flexibility and durability, steel inner casing that is tightly coiled for low compression, pre-lubricated nylon inner sleeve, bird-caged wire ends, EPDM moulded rubber for high UV resistance and injection moulded components manufactured from high-strength POM material.

Features:

• Flexible and durable with steel inner casing that is tightly coiled for low compression.
• Pre-lubricated nylon inner sleeve.
• Bird caged wire ends.
• EPDM moulded rubber for high UV resistance and injection moulded components made from high-strength POM material.

Note: Kit contents may vary by fitment and are subject to change.

Kit contains all of the components to re-seal leaking master cylinders. Includes copper washers, spring, snap ring, replacement screws where applicable, cup seals, boot, and O-rings.

All Balls now offers a complete fork bush kit solution. The kit includes the following products:

• 2x slider bushings
• 2x leg bushings
• All copper washers and O-rings, 2 fork seal snap rings.

Quality design and construction of every All Balls piece meets the toughest standards and conditions — from daily commuting to full-on racing, all older bearing and seal designs are upgraded to the best and latest specs and designs.

When it comes to quality, All Balls knows no compromises. All the products made under stringent quality control conditions. The latest manufacturing methods coupled with the use of the highest-grade materials ensure the closest tolerances are adhered to.

• Nut: 4
• Screw: 4

Kit includes components to rebuild one wheel.

NOTE: This complete Vertex Gasket Set contains all parts as pictured.

Produced in the U.S.A. with the latest materials and technology in gasket production to Vertex specifications. Vertex gaskets ensure long-lasting performance and leak prevention for your rebuild needs. Vertex's replacement gaskets and seals are available as top-end kits, complete engine kits, or as an oil seal kit.

• One kit containing all of the gaskets, O-rings, and valve seals necessary to rebuild the entire engine and transmission.
• Includes transmission seals.

Features a black PVC outer jacket for maximum flexibility and durability, steel inner casing that is tightly coiled for low compression, pre-lubricated nylon inner sleeve, bird-caged wire ends, EPDM moulded rubber for high UV resistance and injection moulded components manufactured from high-strength POM material.

Features:

• Flexible and durable with steel inner casing that is tightly coiled for low compression.
• Pre-lubricated nylon inner sleeve.
• Bird caged wire ends.
• EPDM moulded rubber for high UV resistance and injection moulded components made from high-strength POM material.

Note: Kit contents may vary by fitment and are subject to change.

NOTE:This Vertex Top End Gasket Set contains all components pictured.

Produced in the U.S.A. with the latest materials and technology in gasket production to Vertex specifications. Vertex gaskets ensure long- lasting performance and leak prevention for your rebuild needs. Vertex's replacement gaskets and seals are available as top-end kits, complete engine kits, or as an oil seal kit.

• These sets include the head, base, and exhaust gaskets, valve seals, O-rings and other gaskets to complete a top-end rebuild.

A quality Steering Head Bearing kit from All Balls. Make your bike handle like new!

Features:

• Upgrade ball-type steering bearings to Heavy-Duty Tapered Bearings
• Higher torque load and better wear than OEM ball-style steering bearings.
• Each kit is complete with upper and lower bearing sets and seals.

K&N's high-flow air filters are available as a replacement for your stock motorcycle air filter element. They are custom-engineered to fit your specific application and are designed to provide low restriction and increased performance while providing excellent engine protection for your motorcycle.

Features:

• Designed to provide increased horsepower and torque.
• Pleated media provides a large filtration area, offering long service intervals.
• Multiple layers of woven cotton gauze media offer excellent filtration.
• Application-specific base seal and sealing bead.
• Made in the USA for over 40 years.
• Washable and reusable, pre-oiled and ready to ride!

Specifications:

• Washa ble: Yes
• Filter Material: Cotton Gauze
• Height: 171mm
• Outside Length: 108mm
• Outside Width: 84mm
• Filter Re-Oiling Amount: 15ml

RMSTATOR is specialized in designing and manufacturing innovative electrical and electronic components for Powersports vehicles like motorcycles, ATV, SxS, UTV, snowmobiles, and PWC. Through unrelenting quality control, we ensure that each component meets or exceeds the OEM specs. With over 25 product families, rest assured that you will find the part you need.

• Direct replacement to your original unit
• Plug-and-play, direct fit, easy installation
• Highest grade of lamination materials
• Highest grade of copper winding, resistant to 200 degrees Celsius
• Connector included

Battery condition is extremely important. No stator can work correctly with a bad or weak battery. Always fully charge your battery before performing any charging system tests or replacing parts. If there is any doubt, have the battery load tested or replaced.

Dimensions:

• Interior diameter: 42mm
• Exterior diameter: 104mm
• Thickness: 25mm
• Length of wires stator to grommet: 135mm
• Length of wires grommet to plug: 400mm

Other specifications:

• Number of wires: 3
• Number of plugs: 1
• Number of pins: 3

Wire to wire resistance:

• Alternator: Yellow between Yellow = 0.5 ohms +-20%

Please Note:

1. All electrical components must be fitted by a qualified technician.
2. Before fitting electrical components ensure the root cause of the original failure has been addressed.
3. The absence of either of points 1 or 2 above, will void any warranty.

Quality design and construction of every All Balls piece meets the toughest standards and conditions - from daily commuting to full-on racing, all older bearing and seal designs are upgraded to the best and latest specs and designs.

One kit does it all! All of the bearings, seals, shafts*, bushings, and thrust bearings (if required) in one all-inclusive kit to do the job correctly and completely.

• All bearing shafts manufactured with 52100 bearing steel that is hardened and centerless ground for a precision fit and extended wear life.
• Steel spacers are case-hardened and plated for resistance to wear and corrosion.
• No more hunting around for missing pieces costing you time and extra money.
• Needle thrust bearings have been replaced with Teflon bearings. Designed to live longer in water and dirt.

* Not included in all kits.

Note: A limited number of kits only available with bearings and seals.

These replacement fuel pumps, modules, assemblies, and kit components are designed to meet or exceed OEM specifications, and feature upgrades that improve on the OEM design. Upgraded polymers, brushes, and commutators ensure long life and durability in multiple fuel blends.

• OEM or better performance
• Polished corrosion-resistant case to help minimize seizing during non-operation
• Specifically designed for quiet operation
• Drop-in replacement
• Gradient density fuel strainer for superior contaminant filtration
• Patented check valve technology
• Compatible with modern ethanol-infused pump gasoline

GOLDfren began manufacturing sintered disc brake pads for a wide range of off-road and road motorcycles in 1991, nearly three decades on from their first motorcycle brake pads GOLDfren has become one of the largest aftermarket manufacturers in the motorcycle brake disc pad industry. Their development of next-generation products has kept them at the technological forefront of Sintered Friction Braking providing you with confidence in the performance, durability and reliability of your brakes.

S3 Series:

The S3 sintered compound is optimal in dry and wet conditions for road & off-road motorcycles. For the road application, S3 pads are suitable for both the front and rear brake while on off-road applications the S3 is only recommended for the front brake. The S3 series is designed for low abrasive interaction with the rotor and quieter braking due to the ceramic composite material. It has an HH friction rating and performs better at higher temperatures than the AD compound. Friction materials contain metal-ceramic with a bronze-graphite and non-metallic friction additives are spread evenly on the base fine bronze body to achieve optimal friction properties.

Features:

• Very high static friction coefficient
• Minimal difference between wet and dry braking performance
• Good abrasive resistance
• Low abrasive interaction with the brake rotor material
• Longer life compared to organic and Kevlar composite materials

Application:

• For riders who demand a bit more than average from their bikes
• Recommended on both front and rear brakes (road application)
• Can also be used on the front brakes of off-road bikes and ATVs
• Works well on both dry and wet conditions

Operating Parameters:

• Specific pressure: 3.0 Mpa
• Sliding speed: 45 m/s
• Constant maximum temp: 450°C
• Short time maximum temp: 800°C
• Counter-surfaces: steel disks

What is a sintered brake pad?

GOLDfren only manufacturers sintered brake pads that contain metal-ceramic and ceramic-carbon friction materials, these materials allow for less brake dust and a quieter braking experience. Sintered brake pads are made by fusing together metallic particles under high temperature and pressure which enhances friction properties and pad life, resulting in longer life and stronger braking. Sintered brake pads experience no brake fade when operating at high temperatures and in wet conditions. They also last up to 5 times longer than organic pads and provide additional braking strength. All materials used are environmentally friendly and do not contain any lead, asbestos, fibreglass or formaldehyde.

Reminder: one set of brake pads services one brake disc, if you are servicing multiple discs you will need multiple sets of brake pads.

Quantum replacement fuel pumps, regulators, tank seals and strainers are designed to meet or exceed OEM specifications, and feature upgrades that improve on the OEM design. Upgraded polymers, brushes, and commutators ensure long life and durability in multiple fuel blends.

Features & Benefits

• OEM or better performance
• Polished corrosion-resistant case to help minimize seizing during non-operation
• Specifically designed for quiet operation
• Drop-in replacement
• Gradient density fuel strainer for superior contaminant filtration
• Patented check valve technology
• Compatible with modern ethanol-infused pump gasoline

All the bearings and seal required to refit a wheel in one convenient package.

Features:

• Premium high-speed bearings feature low drag.
• Double lip seals on both sides to provide superior exclusion of water and dirt
• Improved grease retention.

Includes components necessary to complete a piston (top end) rebuild. Competitive pricing, made to meet and exceed OEM quality and designed as a direct OEM replacement.

Features:

• Designed for OEM replacement.
• Made from high-quality materials.
• Meet or exceed OEM specifications.
• Competitive pricing.

A quality Steering Head Bearing kit from All Balls. Make your bike handle like new!

Features:

• Upgrade ball-type steering bearings to Heavy-Duty Tapered Bearings
• Higher torque load and better wear than OEM ball-style steering bearings.
• Each kit is complete with upper and lower bearing sets and seals.

P SERIES - Street Bikes

Premier's most successful general use material, our P series pads, are a tough Kevlar based organic material giving superb brake effect on all sportbikes and cruisers. This material is preselected by the catalogue when you order P prefix disc pads.

P SERIES - Off-Road

Part numbers relating to off-road machines are supplied in carbon graphite compound for medium durability, good brake effect and minimum heat generation.

Includes components necessary to complete a piston (top end) rebuild. Competitive pricing, made to meet and exceed OEM quality and designed as a direct OEM replacement.

Features:

• Designed for OEM replacement.
• Made from high-quality materials.
• Meet or exceed OEM specifications.
• Competitive pricing.

A premium single Bar End Mirror machined from billet aluminium. Easily adjustable and featuring anti-glare convex glass this mirror is designed to fit 22mm / 7/8" handlebars.

Features:

• Can be fitted above or below handlebar
• Suitable for all motorcycle types
• Machined from billet aluminium
• Anti-glare convex glass
• 70mm diameter mirror
• 12 - 18mm expansion bushes
• Easily adjustable
• Universal fitting
• To be used in conjunction with original-fit mirrors.