HARD PARTS

A High Quality Caliper rebuild kit from All Balls. Kit includes evrything required to rebuild a caliper, Washers, Cup seals, Boots and Bolts. Save lots on OEM parts! A High Quality Caliper rebuild kit from All Balls. Kit includes evrything required to rebuild a caliper, Washers, Cup seals, Boots and Bolts. Save lots on OEM parts!

It is time to update or replace your voltage regulator with the advanced MOSFET type.

It runs cooler than all OEM diode style regulators. In addition, this rectifier has overheat protection, rather than burn up it will simply turn off for a while and cool off.

• Direct replacement to your original unit
• Plug-and-play, direct fit, easy installation
• The quality exceeds the OEM equipment
• Higher grade of electric components
• All shipped products are tested

All item pictures are accurate, if in doubt, do not hesitate and compare our item to your original part.

Dimensions:

• Width: 90 mm
• Length: 84 mm
• Height: 78 mm
• Distance between fixation holes center to center: 68 mm

Other specifications:

• Number of plugs: 2
• Number of pins: 5
• Minimum Charging Voltage: 14.5 V +/- 0.5 V
• Maximum Charging Current: 50 A / 500 W
• Open Circuit Voltage: Less than 15 V
• Operating Temperature: -20°C to 85°C

Quality replacement Starter Motors

Please Note:

1. All electrical components must be fitted by a qualified technician.
2. Before fitting electrical components ensure the root cause of the original failure has been addressed.
3. The absence of either of points 1 or 2 above, will void any warranty.

Bolt brand bolts, nuts and washers meet all OEM standards. Designed with precision, each bolt comes in a convenient pack of 10.

RMSTATOR is specialized in designing and manufacturing innovative electrical and electronic components for Powersports vehicles like motorcycles, ATV, SxS, UTV, snowmobiles, and PWC. Through unrelenting quality control, we ensure that each component meets or exceeds the OEM specs. With over 25 product families, rest assured that you will find the part you need.

• Direct replacement to your original unit
• Plug-and-play, direct fit, easy installation
• Highest grade of lamination materials
• Highest grade of copper winding, resistant to 200 degrees Celsius
• Connector included

Battery condition is extremely important. No stator can work correctly with a bad or weak battery. Always fully charge your battery before performing any charging system tests or replacing parts. If there is any doubt, have the battery load tested or replaced.

Please Note:

1. All electrical components must be fitted by a qualified technician.
2. Before fitting electrical components ensure the root cause of the original failure has been addressed.
3. The absence of either of points 1 or 2 above, will void any warranty.

Please Note:

1. All electrical components must be fitted by a qualified technician.
2. Before fitting electrical components ensure the root cause of the original failure has been addressed.
3. The absence of either of points 1 or 2 above, will void any warranty.

A quality caliper rebuild kit from All Balls. Contains everything needed to rebuild your caliper to like new condition.

Quality replacement Regulator/Rectifiers.

Please Note:

1. All electrical components must be fitted by a qualified technician.
2. Before fitting electrical components ensure the root cause of the original failure has been addressed.
3. The absence of either of points 1 or 2 above, will void any warranty.

Please Note:

1. All electrical components must be fitted by a qualified technician.
2. Before fitting electrical components ensure the root cause of the original failure has been addressed.
3. The absence of either of points 1 or 2 above, will void any warranty.

Each pack of Premier CSK Clutch Springs contains a complete set of heavy-duty springs. Up to 15% stronger than the original.

Customer should be advised that after installation of a CSK kit the clutch lever will feel slightly ‘heavier’ than standard

Manufactured to OEM specifications and tolerances to guarantee quality and superior durability. Dust seals feature external garter springs to keep the fork tubes clean from dust and grime.

Features:

• Made of high-quality vulcanized rubber.
• Fits as well as OEM.
• Three to four times the life than OEM.

Protective heat cover designed for specific Harley Davidson model applications where battery is located very close to engine.

Key features:

• Protects Motobatt MBTX30U (standard) and MBTX30UHD (black/orange) batteries from engine heat.
  
  
• Designed for low-profile, snug fit around battery, without interfering with terminals.

Please Note:

1. All electrical components must be fitted by a qualified technician.
2. Before fitting electrical components ensure the root cause of the original failure has been addressed.
3. The absence of either of points 1 or 2 above, will void any warranty.

Quality design and construction of every All Balls piece meets the toughest standards and conditions - from daily commuting to full-on racing, all older bearing and seal designs are upgraded to the best and latest specs and designs.

Available individually in left-hand and right-hand thread or sold in pairs one L/H and one R/H thread.

Please Note:

1. All electrical components must be fitted by a qualified technician.
2. Before fitting electrical components ensure the root cause of the original failure has been addressed.
3. The absence of either of points 1 or 2 above, will void any warranty.

Upgrade rubber bushings found in Utility ATV A-Arms to redesigned HD Delrin bushings. Designed to replace worn-out rubber bushings and provides greater suspension travel and performance.

Please Note:

1. All electrical components must be fitted by a qualified technician.
2. Before fitting electrical components ensure the root cause of the original failure has been addressed.
3. The absence of either of points 1 or 2 above, will void any warranty.

All Balls OEM replacement air filters are manufactured to meet or exceed OEM specifications. Constructed to fit the factory air box and are direct replacements to OEM air filters. The premium filtering media prevents dirt and dust from entering your engine while maintaining excellent airflow.

• OEM replacement air filter
• Meets or exceeds OEM specifications
• Fits factory air box
• Excellent airflow
• Premium filtration

A quality Steering Head Bearing kit from All Balls. Make your bike handle like new!

Features:

• Upgrade ball-type steering bearings to Heavy-Duty Tapered Bearings
• Higher torque load and better wear than OEM ball-style steering bearings.
• Each kit is complete with upper and lower bearing sets and seals.

NOTE: This Vertex Top End Gasket Set contains all components pictured.

Produced in the U.S.A. with the latest materials and technology in gasket production to Vertex specifications. Vertex gaskets ensure long-lasting performance and leak prevention for your rebuild needs. Vertex's replacement gaskets and seals are available as top-end kits, complete engine kits, or as an oil seal kit.

• These sets include the head, base, and exhaust gaskets, valve seals, O-rings and other gaskets to complete a top-end rebuild.

Includes components necessary to complete a piston (top end) rebuild. Competitive pricing, made to meet and exceed OEM quality and designed as a direct OEM replacement.

Features:

• Designed for OEM replacement.
• Made from high-quality materials.
• Meet or exceed OEM specifications.
• Competitive pricing.

All the bearings and seal required to refit a wheel in one convenient package.

Features:

• Premium high-speed bearings feature low drag.
• Double lip seals on both sides to provide superior exclusion of water and dirt
• Improved grease retention.

K&N Replacement Air Filter for some Harley Davidson Sportster 883 and 1200 models with Screamin' Eagle Upgrade. K&N lifetime replacement air filters are designed to increase horsepower and acceleration while providing excellent filtration.

Features:

• High airflow with excellent filtration.
• Washable and reusable.
• Designed to increase horsepower.
• Environmentally friendly.

Specifications:

• H eight: 1.875in (48mm)
• Washable: Yes
• Filter Material: Cotton Gauze
• Width: 6in (152mm)
• Length: 9.375in (238mm)
• Filter Re-Oiling Amount: 0.44oz (13ml)

A quality caliper rebuild kit from All Balls. Contains everything needed to rebuild your caliper to like new condition.