HARD PARTS

Ideal replacement for dirt bikes.

Features:

• Anti-swell alloy impregnated heavy-duty cork-based facings.
• Smooth clutch take up compared to paper clutches, which can ‘snatch’.
• Steel separator plates increase flywheel effect of the engine and improve performance.

K&N's high-flow air filters are available as a replacement for your stock motorcycle air filter element. They are custom-engineered to fit your specific application and are designed to provide low restriction and increased performance while providing excellent engine protection for your motorcycle.

Features:

• Designed to provide increased horsepower and torque.
• Pleated media provides a large filtration area, offering long service intervals.
• Multiple layers of woven cotton gauze media offer excellent filtration.
• Application-specific base seal and sealing bead.
• Made in the USA for over 40 years.
• Washable and reusable, pre-oiled and ready to ride!

Specifications:

• Height: 1.25in (32mm)
• Washable: Yes
• Filter Material: Cotton Gauze
• Filter Re-Oiling Amount: 0.39oz (11ml)

K&N off-road replacement air filters are ideal for extended use in dirty and dusty off-road riding and provide clean carburetion even at high altitude. Generally, no jet changes are required with just a K&N filter element. K&N replacement air filters are washable and reusable and provide high air-flow with excellent filtration.

Features

• Designed to provide increased horsepower and acceleration.
• Pleated cotton media provides a large filtration area offering low restriction, high-capacity and long service intervals.
• Multiple layers of woven cotton gauze media offer excellent filtration.
• Fits directly into OEM airbox with an application-specific sealing bead ensuring a precise fit.
• No fuel management modifications are required to obtain increased performance.
• Washable and reusable, most are pre-oiled and ready to ride.

Specifications

• Height : 1.438in (37mm)
• Washable: Yes
• Filter Material: Cotton Gauze
• Outside Length: 7.75in (197mm)
• Outside Width: 6.938in (176mm)
• Filter Re-Oiling Amount: 1.18oz (35ml)

All necessary parts to replace the fuel pump module.

Features:

• Includes complete module, retaining nut and gasket.
• Restores lost performance or non-functioning fuel pump with this economical solution.
• Pump draws less current than OEM counterpart while maintaining the same flow rate at working pressure, which reduces working temperatures and increases the life of the unit.

Note: Specific parts vary from kit to kit depending on the needs of your vehicle model.

Please note: Credit returns of correctly supplied kits will only be accepted if in original unopened packaging, and are subject to a 25% restocking fee.

Whites Off-Road Refurb Kits are an industry-leading comprehensive kit for exceptional service of your or a customer's off-road motorcycle. A complete one-stop shop that makes servicing a breeze. The Whites Off-Road Refurb Kits are conveniently packaged together, saving you time. High-grade materials are used for the exceptional ongoing performance of the motorcycle, guaranteed to provide superior durability and reliability.

Kits include bearings, cables, and pads.

NOTE: Brand of included components may vary. Check the image to verify the contents.

Please Note:

1. All electrical components must be fitted by a qualified technician.
2. Before fitting electrical components ensure the root cause of the original failure has been addressed.
3. The absence of either of points 1 or 2 above, will void any warranty.

Includes components necessary to complete a piston (top end) rebuild. Competitive pricing, made to meet and exceed OEM quality and designed as a direct OEM replacement.

Features:

• Designed for OEM replacement.
• Made from high-quality materials.
• Meet or exceed OEM specifications.
• Competitive pricing.

All Balls Differential Bearing & Seal Only Kit Front

In one box, you'll get all of the bearing and seals you'll need for replacing on a differential. All Balls manfactures a wide range of High-Quality design and construction products that meet the toughest standards and conditions.

All the bearings and seal required to refit a wheel in one convenient package.

Features:

• Premium high-speed bearings feature low drag.
• Double lip seals on both sides to provide superior exclusion of water and dirt
• Improved grease retention.

NOTE: This Wossner Piston Kit does NOT include Piston Rings and Needle Bearings.

Wossner is Germany's finest aftermarket forged piston and rod manufacturer and have over 25 years of experience in the high-performance racing industry. Top European racers and FIM World Champions rely on Wossner for only the best pistons, rods and customer service.

Features:

• In-house designed and manufactured; all forgings are produced in Wossner's company-owned forging operation
• 4-stroke pistons are made using a double-bridged forging design
• Lightweight pistons with the tightest piston-wall clearances in the industry give you a quieter running engine
• Wossner pistons are used by leading Supercross, Arenacross and MX GP teams
• Made in Germany

Specifications:

• Piston Size: 76.97mm
• Oversize: 0.01mm

• Stainless steel reduces thermal conductivity by up to 90% compared to aluminum
• Reduced braking temperatures provide better braking performance
• Eliminates the potential for becoming brittle or corroded like composite or chrome-plated pistons, thus extending braking performance
• Eliminates failure-prone ceramic inserts used on some models

Bolt brand bolts, nuts and washers meet all OEM standards. Designed with precision, each bolt comes in a convenient pack of 10.

• Precision machined from high-grade 304 Stainless Steel.
• Stainless steel reduces thermal conductivity by up to 93% compared to aluminium.
• Plastic composite pistons are prone to damage and become brittle with age.
• OEM chrome-plated steel and aluminium pistons are prone to corrosion.
• Eliminates failure prone ceramic inserts found on some KTM models.
• Each kit contains piston or pistons to rebuild one caliper.

4-pack of replacement Fuel Star fuel line clamps for the All Balls Complete OEM Style Fuel Line Clamp Kit.

• Inside Diameter: 10.1mm
• Clamp Style: Wire
• Quantity: 4

Crafted from military-spec certified TI3Al titanium alloy, Vertex Titanium Valves are made to endure the harshest racing conditions. Forged from a single blank, grain flow is improved to enhance the mechanical characteristics of the valve without having to resort to welding. Special PVD, CVD, and CrN coatings are used to provide low-friction surfaces that reduce heat generation and resist carbon build-up; coatings allow alloys like titanium to become ultra-smooth while reaching hardness levels 5x that of high-speed steel.

• Military-spec certified TI3Al titanium alloy
• Forged from a single blank
• PVD, CVD, and CrN coatings
• Reduces heat generation
• Resists carbon build-up
• Significantly stronger than steel

Specifications:

• Material: Titanium
• Overall Length: 80mm
• Seat Angle: 45°
• Valve Head Outer Diameter: 23mm
• Valve Length: 80mm
• Valve Stem Outer Diameter: 3.980mm

Quality design and construction of every All Balls piece meets the toughest standards and conditions - from daily commuting to full-on racing, all older bearing and seal designs are upgraded to the best and latest specs and designs.

Available individually in left-hand and right-hand thread or sold in pairs one L/H and one R/H thread.

NOTE: This complete Vertex Gasket Set contains all parts as pictured.

Produced in the U.S.A. with the latest materials and technology in gasket production to Vertex specifications. Vertex gaskets ensure long-lasting performance and leak prevention for your rebuild needs. Vertex's replacement gaskets and seals are available as top-end kits, complete engine kits, or as an oil seal kit.

• One kit containing all of the gaskets, O-rings, and valve seals necessary to rebuild the entire engine and transmission.
• Includes transmission seals.

The HFP-182 is a low-pressure frame mounted electric fuel pump for 1999-2014 carburetted Polaris Ranger 400/ 500 ATV/ UTV's.  This pump is a direct replacement for Polaris part numbers 4011545, 4011492, 4010658, 4170020.

• OEM or better performance
• Polished corrosion-resistant case to help minimize seizing during non- operation
• Specifically designed for quiet operation
• Drop-in replacement
• Patented check valve technology
• Compatible with modern diesel and ethanol-infused pump gasoline

A low-pressure frame mounted electric fuel pump for 1999-2014 carburetted Polaris Ranger 400/ 500 ATV/ UTV's.  This pump is a direct replacement for Polaris part numbers 4011545, 4011492, 4010658, 4170020.

• OEM or better performance
• Polished corrosion-resistant case to help minimize seizing during non-operation
• Specifically designed for quiet operation
• Drop-in replacement
• Patented check valve technology
• Compatible with modern diesel and ethanol-infused pump gasoline

Brand new aftermarket Stator + Machined Aluminum Mosfet Regulator Kit

• Direct replacement to your original unit
• Plug-and-play, direct fit, easy installation
• Harness and Gasket Included
• Include 3X OF M6-1.00 X 30 Allen socket head
• All shipped products are tested

Brand new aftermarket Stator

• Highest grade of lamination materials
• Highest grade of copper winding, resistant to 200 degrees Celsius
• Tow pick up pulsar coil included
• Connectors included
• Rubber grommet included

Brand new RMSTATOR Red Machined Aluminum Mosfet Regulator

Our new RMSTATOR machined aluminium Mosfet voltage regulator is a great upgrade for heat dissipation in any powersports charging system. After 10 minutes of use, our billet aluminium heatsink runs cooler by 33% than standard cast regulator housings. Our new RMSTATOR red regulator, equipped with the renowned Mosfet regulation technology, is an added value to any three-phase permanent magnet charging system.

STOP BURNING YOUR REGULATOR RECTIFIER! It is time to update or replace your voltage regulator with the advanced MOSFET type.

It runs cooler than all OEM diode style regulators. In addition, this rectifier has overheat protection, rather than burn up, it will simply turn off for a while and cool off.

• The quality exceeds the OEM equipment
• Improved heat sink and charging capabilities
• Higher grade of electric components

We have even included the opposite connector (main harness side) as we know these are often melted/corroded/defective and a major cause of repetitive electrical issues.

Why use Mosfet Enhanced technology?

• Runs cooler: Runs much cooler than the traditional Shunt voltage regulator rectifier.
• Saves gas: Less load on the stator, less work, less fuel is used and you save.
• Regulated energy: The power charging your battery is steadier and smooth.
• Extended battery life: Extends the battery’s life and cold cranking capacity.
• More engine power: Removes stator load resulting in more engine power.
• Optimized power: Optimize power delivery by switching the stator coils on or off.
• With Enhance Technology design: This product is an advanced design that lowers operating temperatures for extended longevity and better performance than the OEM part.

Stator Dimensions

• Interior diameter: 54mm
• Exterior diameter: 115mm
• Thickness: 14mm
• Length of wires stator to grommet: 160mm
• Length of wires grommet to plug: 1180mm

Other specifications:

• Number of wires: 3
• Number of plugs: 1
• Number of pins: 3
• Number of poles: 18

Wire to wire resistance:

• Alternator 3p: Yellow to Yellow = 0.8 ohms +-20%
• Pickup: Green to Blue = 500 ohms +-20%

Regulator Dimensions:

• Width: 103mm
• Length: 103mm
• Height: 28mm
• Distance between fixation holes centre to centre: 80mm

Other specifications:

• Number of plugs: 2
• Number of pins: 5
• Minimum Charging Voltage: 14.5 V +- 0.5 V
• Maximum Charging Current: 50 A / 500 W
• Open Circuit Voltage: < 15 V
• Operation Temperature: -20°C to 85°C

Please Note:

1. All electrical components must be fitted by a qualified technician.
2. Before fitting electrical components ensure the root cause of the original failure has been addressed.
3. The absence of either of points 1 or 2 above, will void any warranty.

K&N Powersports Cartridge Oil Filters are designed to satisfy the needs of racers and engine builders as well as the average motorcycle or ATV owner who wants the best oil filter available. K&N Powersports Oil Filters trap harmful contaminants while the filter's construction allows for high oil flow rates.

Features

• High-performance design for outstanding filtration.
• High-efficiency media with uniform pleats.
• Oil filter design provides for a high rate of oil flow.
• Ideal for high-end synthetic motor oil.

Specifications

• Style: Cartridge
• Filter Material: High Flow Premium Media
• Gasket Material: Nitrile Rubber
• Height: 49mm
• Outside Diameter: 38mm
• Inside Diameter: 12mm

Ideal replacement for dirt bikes.

Features:

• Anti-swell alloy impregnated heavy-duty cork-based facings.
• Smooth clutch take up compared to paper clutches, which can ‘snatch’.
• Steel separator plates increase flywheel effect of the engine and improve performance.

Introducing our newest heavy-duty recall-type charging system upgrade kit for Aprilia 2009-2020 RSV4 & 2011-2020 Tuono V4.

Anyone who rides or repairs Aprilia’s motorcycles is probably familiar with the stator, flywheel, and sometimes voltage regulator issues common to these models. Most of these bikes will have had at least one stator fail in their lifetime so far. The main problem was extremely strong magnets were used on the original flywheels, creating a very high power stator output, which generated excessive heat. This usually resulted in burned-up, or shorted stator winding, and often in a failed voltage regulator.

The solution was a new flywheel from Kokusan with lower-strength magnets, dropping the stator output and heat generation. This results in a charging system output perfectly matched for the bike’s electronic needs and the long-term reliability of the stator and voltage regulator.

To prevent or correct the flywheel problems, our engineers at RMS Labs have come up with a completely reliable heavy-duty charging system replacement kit for your Aprilia. Upgrade today if you haven’t already!

Included in this kit

• Heavy-duty Kokusan brand recall-type OEM flywheel
• Triple-tested heavy-duty stator
• Flywheel puller

With this kit, you will be able to upgrade your current failure-prone charging system with a heavy-duty version using the latest technologies

Features:

• Kokusan upgrade/recall type flywheel: Lower-strength magnets for correct stator output, low heat generation, and long-term reliability.
• Built to OEM size: Fits precisely in your ride: install it and forget it.
• Improved epoxy: Uses high-temperature epoxy that is stronger than OEM, eliminating the possibility of magnet detachment
• High-grade steel capping: Prevents harsh additives in motor oil from degrading the epoxy attaching the magnets. Though extremely unlikely, if a magnet did ever come loose, it would remain in the sleeve preventing contact with the stator.
• Precise balancing: Eliminates crankshaft vibrations for longer engine longevity.
• Shop with confidence:
All products are tested. Don't waste time with temporary solutions, and start fixing your ride like a pro!

Specifications:

• Stator Dimensions:
• Interior diameter: 43 mm
• Exterior diameter: 105 mm
• Thickness: 13.8 mm
• Length of wires stator to grommet: 125 mm
• Length of wires grommet to plug: 320 mm
• Other specifications:
• Number of wires: 3
• Number of plugs: 1
• Number of pins: 3
• Alternator: Between each Yellow = 0.3 ohms +-20%
• Flywheel Dimensions:
• Exterior Diameter: 121 mm
• Interior Diameter: 107 mm
• Interior Diameter Center Housing: 19 mm
• Exterior Diameter Center Housing: 33 mm
• Thickness (exterior): 35.3 mm
• Thickness (interior): 30.65 mm
• Flywheel Puller:
• 36 mm x 1.5 right-hand male
• Length: 60 mm
• Exterior Diameter: 48 mm
• Interior Diameter: 35 mm
• Exterior Diameter Center Housing: 37 mm

Please note: There are two possible kits for the RSV4 engine. This kit ONLY fits RSV4 engine numbers HIGHER than 3413 with KOKUSAN flywheels. Please compare our flywheel to your original.

If your RSV4 engine number is LOWER than 3413, your motor uses the Mitsubishi flywheel and will need Stator Assembly 857201. Refer to kit RMS900-104929.

Please Note:

1. All electrical components must be fitted by a qualified technician.
2. Before fitting electrical components ensure the root cause of the original failure has been addressed.
3. The absence of either of points 1 or 2 above, will void any warranty.

Upgrade your motorcycle's clutch system with the All Balls Racing Motorcycle Clutch Cable. Designed with precision and durability in mind, this clutch cable delivers exceptional performance and reliability on the road.

• Black PVC outer jacket for maximum flexibility and durability.
• Steel inner casing that is tightly coiled for low compression.
• A pre-lubricated nylon inner sleeve guarantees smooth operation and long life.
• All wire ends are bird-caged prior to terminal casting for superior pull-out resistance.
• EPDM-moulded rubber components for high UV resistance and long life.
• Injected moulded components are manufactured from high-strength POM material.

RMSTATOR is specialized in designing and manufacturing innovative electrical and electronic components for Powersports vehicles like motorcycles, ATV, SxS, UTV, snowmobiles, and PWC. Through unrelenting quality control, we ensure that each component meets or exceeds the OEM specs. With over 25 product families, rest assured that you will find the part you need.

• Direct replacement to your original unit
• Quality exceeds the OEM equipment

Please Note:

1. All electrical components must be fitted by a qualified technician.
2. Before fitting electrical components ensure the root cause of the original failure has been addressed.
3. The absence of either of points 1 or 2 above, will void any warranty.

Quality carburettor rebuild kit from All Balls.

• Kits include all of the necessary components to repair a carburettor. ATV models with two carburettors include components to repair two carburettors.
• Kit includes necessary all O-rings, gaskets, jets, needle, mixture screw, float bowl screws, float valve needles and seat. (Needle jet and other pressed-in jets are not included in the kit.)
• OEM jet sizes are included in the kit. NBR rubber material is used on all O-rings and rubber gaskets NBR has excellent resistance to the ethanol used in today’s fuels.
• Applications that use paper float bowl gaskets are upgraded to High-Performance Interface Gasket material.
• Components included in the kits are based on US models and discretion must be used when attempting to install the kit on a non-US model.
• Off-road use only.