HARD PARTS

A quality caliper rebuild kit from All Balls. Contains everything needed to rebuild your caliper to like new condition.

Brand new aftermarket stator

• Direct replacement to your original unit
• Plug-and-play, direct fit, easy installation
• Highest-grade lamination materials
• Highest-grade copper windings, resistant to 200 degrees Celsius.
• Pick up pulsar coil included
• Connector included
• Rubber grommet included
• All products shipped are tested

Specifications:

Dimensions:

Other specifications:

• Number of wires: 5
• Number of plugs: 4
• Number of pins: 5
• Number of poles: 18

Wire-to-wire resistance:

• Alternator: White to White = 0.5 ohms +-20%
• Pickup: Black to Grey = 512 ohms +-20%

A quality caliper rebuild kit from All Balls. Contains everything needed to rebuild your caliper to like new condition.

Produced in the U.S.A. with the latest materials and technology in gasket production to Vertex specifications. Vertex gaskets ensure long-lasting performance and leak prevention for your rebuild needs. Vertex's replacement gaskets and seals are available as top-end kits, complete engine kits, or as an oil seal kit.

• One kit containing all of the gaskets necessary to rebuild the water pump.
• Designed to fit O.E.M. water pump.

K&N's high-flow air filters are available as a replacement for your stock motorcycle air filter element. They are custom-engineered to fit your specific application and are designed to provide low restriction and increased performance while providing excellent engine protection for your motorcycle.

Features:

• Designed to provide increased horsepower and torque.
• Pleated media provides a large filtration area offering long service intervals.
• Multiple layers of woven cotton gauze media offer excellent filtration.
• Application-specific base seal and sealing bead.
• Made in the USA for over 40 years.
• Washable and reusable, pre-oiled and ready to ride!

Specifications:

• Filte r Material: Cotton Gauze
• Height: 33mm
• Width: 158mm
• Length: 227mm
• Filter Re-Oiling Amount: 20ml

Please Note:

1. All electrical components must be fitted by a qualified technician.
2. Before fitting electrical components ensure the root cause of the original failure has been addressed.
3. The absence of either of points 1 or 2 above, will void any warranty.

Short stem Rectangle Mini LED replacement indicators.

Features

• 9 super-bright LEDs
• Compact and stylish design
• Weatherproof
• Sealed-for-life for greater longevity
• Includes 2 resistors to control flash rate on most motorbikes
• Specification: 12V, 1W
• Instructions included
• E-marked for front and rear use
• M8 bolt - thread pitch 1.25mm
• Size: 74mm (L) x38mm (W) x 33mm (H)

Please Note:

1. All electrical components must be fitted by a qualified technician.
2. Before fitting electrical components ensure the root cause of the original failure has been addressed.
3. The absence of either of points 1 or 2 above, will void any warranty.

• Direct OEM replacement at a fraction of the cost
• Includes valve, hose, gaskets, screws, clamps and everything needed to replace the OEM petcock
• Viton rubber fuel resistant gaskets
• Includes OE style fuel line and clamps

Hot Cams Steel Valves are designed as OEM replacements, precision-forged they are strong & durable. Machined head and seat surfaces provide a precise fit. Hot Cams valves are nitride coated and induction hardened valve stem tip provide longevity while a precision polished surface reduces friction resulting in less heat build-up. Hot Cams valves are compatible with all OEM valve keepers and are sold individually allowing you to keep your replacement costs down.

• Forged one-piece OEM replacement valves
• Precision machined valve head and seat surfaces
• Nitride coated
• Induction hardened valve stem tip
• Precision polished surface
• Compatible with OEM valve keepers
• Sold each

Specifications:

• Material: Stainless Steel
• Valve Head Outer Diameter: 35mm
• Valve Length: 97mm
• Valve Stem Outer Diameter: 5.970mm

When it comes to quality, All Balls knows no compromises. All the products made under stringent quality control conditions. The latest manufacturing methods coupled with the use of the highest-grade materials ensure the closest tolerances are adhered to.

• Nut: 4
• Screw: 4

Quality replacement components to rebuild one fuel tap. Improves service life and resistance to water and dirt.

Includes:

• Face screws
• Face gasket
• Wave washer
• Tank bolts
• Tank gasket
• O-rings

All necessary parts to replace the fuel pump module.

Features:

• Includes complete module, retaining nut and gasket.
• Restores lost performance or non-functioning fuel pump with this economical solution.
• Pump draws less current than OEM counterpart while maintaining the same flow rate at working pressure, which reduces working temperatures and increases the life of the unit.

Note: Specific parts vary from kit to kit depending on the needs of your vehicle model.

Upgrade your motorcycle's clutch system with the All Balls Racing Motorcycle Clutch Cable. Designed with precision and durability in mind, this clutch cable delivers exceptional performance and reliability on the road.

• Black PVC outer jacket for maximum flexibility and durability.
• Steel inner casing that is tightly coiled for low compression.
• A pre-lubricated nylon inner sleeve guarantees smooth operation and long life.
• All wire ends are bird-caged prior to terminal casting for superior pull-out resistance.
• EPDM-moulded rubber components for high UV resistance and long life.
• Injected moulded components are manufactured from high-strength POM material.

PR SERIES – Off-Road Sintered

Premier PR pads have been upgraded to a new HIGH DENSITY sintered metal compound suitable for all types of moto-x and ATV use.

Includes components necessary to complete a piston (top end) rebuild. Competitive pricing, made to meet and exceed OEM quality and designed as a direct OEM replacement.

Features:

• Designed for OEM replacement.
• Made from high-quality materials.
• Meet or exceed OEM specifications.
• Competitive pricing.

Each pack of Premier CSK Clutch Springs contains a complete set of heavy-duty springs. Up to 15% stronger than the original.

Customer should be advised that after installation of a CSK kit the clutch lever will feel slightly ‘heavier’ than standard

Includes components necessary to complete a piston (top end) rebuild. Competitive pricing, made to meet and exceed OEM quality and designed as a direct OEM replacement.

Features:

• Designed for OEM replacement.
• Made from high-quality materials.
• Meet or exceed OEM specifications.
• Competitive pricing.

The All Balls CV Boot material is compounded from an OEM grade DCR66 rubber that is formulated specifically for the demanding requirements of today’s ATVs and UTVs.

• 40% higher tensile strength than conventional CV boo material, suitable for the high joint angles of modern ATVs and UTVs.
• 50% more abrasion-resistant than conventional CV boot material to ensure a long life in harsh off-road environments.
• Rubber compound is tested to -40° F to ensure good performance and long life at low temperatures.
• Lithium-based Molybdenum Grease ensures good lubrication for long CV joint life. Easier to install than most OEM and aftermarket boots. Sold each. Does not require the use of a ""Banding Tool"".

Specifications:

• H: 80mm
• SD: 16mm
• LD: 60mm
• Shaft I.D.: 16
• CV Body I.D.: 60
• Length: 80

Kits include:

• Two stainless steel clamps that are designed to be tightened without the use of special tools.

Includes components necessary to complete a piston (top end) rebuild. Competitive pricing, made to meet and exceed OEM quality and designed as a direct OEM replacement.

Features:

• Designed for OEM replacement.
• Made from high-quality materials.
• Meet or exceed OEM specifications.
• Competitive pricing.

K&N Powersports oil filters contain a modern synthetic filter media, designed for ultimate flow with less pressure drop, yet engineered for outstanding filtration. K&N Powersports 'spin-on' oil filters feature a heavy-duty metal can. Most of these have a 17 mm nut affixed onto the end that allows for easy removal. The 17mm nut is crossed-drilled so racers can safety wire the filter to their bike.

Features

• O/E replacement oil filters for most cars, trucks, SUVs, motorcycles, and ATVs
• 17mm exposed nut designed for easy oil filter removal.
• Heavy-duty construction for extreme conditions.
• Anti-drain back valve (where applicable) eliminates dry starts.

Specifications

• Styl e: Canister
• Filter Material: High Flow Premium Media
• Gasket Material: Nitrile Rubber
• Height: 71mm
• Outside Diameter: 68mm
• Thread Specification: 3/4 In. 16 UNF
• Removal Nut: Yes

These HotGrips™ are universal, but have been designed to be compatible with motorcycles which have smaller batteries and less powerful charging systems. Therefore, they draw less current than other HotGrips™ such as those in the Oxford Premium and Advanced ranges.

Soft, ultra-grippy rubber provides comfort & feedback and if required, the grips can be cut down to size.

Key features:

• Weather resistant heat controller
• 2 way switch with High/Low function
• Draws under 3.2A
• Rainproof, double bonded, sealed for life switch
• Fits 22mm handlebars
• Moulded wiring arrangement is both durable and discreet
• Unique Oxford tread design
• Small size: 52 x 30 x 24mm (W x D x H)

Includes:-

• 2 x HotGrips™
• 1 x heat controller
• 1 x bracket and fittings for mounting the heat controller
• 1 x wiring loom, cable ties and grip glue
• 1 x instruction booklet and warranty form

NOTE: This complete Vertex Gasket Set contains all parts as pictured.

Produced in the U.S.A. with the latest materials and technology in gasket production to Vertex specifications. Vertex gaskets ensure long-lasting performance and leak prevention for your rebuild needs. Vertex's replacement gaskets and seals are available as top-end kits, complete engine kits, or as an oil seal kit.

• One kit containing all of the gaskets, O-rings, and valve seals necessary to rebuild the entire engine and transmission.
• Includes transmission seals.

NOTE: This Vertex Top End Gasket Set contains all components pictured.

Produced in the U.S.A. with the latest materials and technology in gasket production to Vertex specifications. Vertex gaskets ensure long-lasting performance and leak prevention for your rebuild needs. Vertex's replacement gaskets and seals are available as top-end kits, complete engine kits, or as an oil seal kit.

• These sets include the head, base, and exhaust gaskets, valve seals, O-rings and other gaskets to complete a top-end rebuild.

Fuel pump strainers act as a first line of defence against fuel system contamination. Strainers filter out common contaminants found in gasoline such as dirt, dust and other particulate matter, as well as gasoline varnish. Quantum fuel pump strainers feature multiple layers of strainer media to filter progressively smaller particle sizes. The expanded surface area provides enhanced filtration, extending the life of the fuel pump.

Restricted fuel flow through a clogged strainer causes the fuel pump to work harder, reducing pump longevity. Strainer clogging is among the top causes of fuel pump failure making it important to replace your strainer regularly - before problems arise. We recommend replacing fuel pump strainers in powersports applications once a year as part of a preventative maintenance plan.

Features:

• Designed with gradient density to meet or exceed OE specifications.
• Designed to ensure optimal filtration to prevent fuel system contamination.
• Strainer material tested and validated for capacity and efficiency by accredited third party.

This K&N racing air filter has just two layers of cotton to provide even lower air restriction than our replacement air filter for street vehicles. Unlike K&N replacement air filters, fuel management modifications will be necessary with this racing filter. K&N racing air filters are washable and reusable.

Features:

• Designed to increase horsepower and acceleration.
• Designed for racing and track applications, not for street use.
• Washable and reusable air filter.
• Low restriction.

Specifications

• Washa Yes
• Filter Material: Cotton Gauze
• Height: 90mm
• Base Outside Length: 248mm
• Base Outside Width: 171mm
• Top Outside Length: 157mm
• Top Outside Width: 81mm
• Filter Re-Oiling Amount: 11ml