New Arrivals

All Balls Master Cylinder repair kit .

Kit includes water pump cover gasket or o-ring, water pump shaft bearing(s) and seal(s) to repair a leaking water pump seal and/or a failed bearing.

Features:

• Precision micro bearings provide OE quality and durability.
• High pressure/temperature mechanical and rubber seals.

Please Note:

1. All electrical components must be fitted by a qualified technician.
2. Before fitting electrical components ensure the root cause of the original failure has been addressed.
3. The absence of either of points 1 or 2 above, will void any warranty.

• Direct OEM replacement at a fraction of the cost
• Includes valve, hose, gaskets, screws, clamps and everything needed to replace the OEM petcock
• Viton rubber fuel resistant gaskets
• Includes OE style fuel line and clamps

Please Note:

1. All electrical components must be fitted by a qualified technician.
2. Before fitting electrical components ensure the root cause of the original failure has been addressed.
3. The absence of either of points 1 or 2 above, will void any warranty.

Rough riding calls for stronger axles and that’s where All Balls Racing excels. Machined for exact OEM fit, the shaft is made of chromoly steel with a larger diameter than most axles. The axle has 6 ball bearings in each CV joint. Laminate coating resists corrosion and rust and protects axles from dirt, water, rocks and grease. Waterproof neoprene boots act as a first line of defence, shielding vulnerable joints and preventing leaks. High-performance molybdenum grease reduces heat and friction.

In static torsion trials, these axles were up to 30% stronger than OEM and aftermarket competition.

Features:

• 40% stronger than OEM.
• Larger 4340 chrome-moly steel axle bar.
• Precision ground components.
• Low profile clamps.
• Lasts approximately 50 percent longer than many aftermarket competitors.
• Neoprene boots.
• Typically runs almost 130,000 cycles versus 80,000 cycles for many axles.
• Engineered in the USA.
• Manufactured in an ISO facility.Assembled with 3% molybdenum grease.

This is an accessory cable, which when used with a HelmetLok (sold separately) will secure one or two helmets together or your jacket and helmet.

Pass one end of the cable through a convenient part of your bike, thread the other end through the loop then through the kit you want to secure. Use a HelmetLok to secure the end of the cable to your bike (see below)...done! When you’re done roll up the cable, slip it and you HelmetLok into the included neoprene storage bag and pop it your jacket pocket, top box or pannier.

The cable is vinyl coated, 5mm in diameter and 1.5 metres long with a loop at each end.

Improve the stability and confidence of your pillion rider with the Whites Passenger Pillion Handle, designed to go around the riders waist this device provides the pillion with convenient handles to hold while riding improving their grip and stability on the bike, especially when accelerating. The belt fits waist sizes 36" to 50" and is constructed using high-strength bonded nylon thread. The mesh inner lining and an ergonomic design provide rider comfort.

• Improves stability for the pillion
• Provides confidence
• Gives a pillion firm mount to hold onto
• Fits waist sizes 36" to 50"
• High-strength bonded nylon thread
• Mesh inner lining for breathability
• Ergonomic design for rider comfort

All new assembly sold complete with Hot Rods connecting rod.

• The Hot Rods complete crankshaft includes their famed connecting rod; durability at a level OEM rods can only dream of.
• Factory assembled and trued to O.E.M. specifications, Hot Rods cranks will meet or surpass the OEM in performance. Hot Rods makes installing the complete crankshaft simple and easy.
• Crankshaft is completely rebuildable with genuine Hot Rods connecting rods.

Note: Crank bearings and seals sold separately.

Quality replacement components to rebuild one fuel tap. Improves service life and resistance to water and dirt.

Includes:

• Face screws
• Face gasket
• Wave washer
• Tank bolts
• Tank gasket
• O-rings

Pin for the Whites Headstock Stand.

Quality pair of fork oil seals from All Balls Racing.

Features:

• Dyno tested to last 3 to 4 times longer than OEM seals.
• Directional ribs on outside of seal allow seal to be installed easily.
• Dual-sealing lips guarantee oil stays in and dirt stays out.

GOLDfren began manufacturing sintered disc brake pads for a wide range of off-road and road motorcycles in 1991, nearly three decades on from their first motorcycle brake pads GOLDfren has become one of the largest aftermarket manufacturers in the motorcycle brake disc pad industry. Their development of next-generation products has kept them at the technological forefront of Sintered Friction Braking providing you with confidence in the performance, durability and reliability of your brakes.

K5 Series:

The K5 sintered compound is optimal for off-road motorcycles and ATVs. It is recommended for riders who demand great off-road stopping power and brake pad durability when riding on tough off-road terrains. The K5 series is designed for low abrasive interaction with the rotor, long life and self-cleaning capabilities necessary in off-road riding conditions. Friction materials contain metal-ceramic with a sophisticated bronze-graphite and full-metal mixture formulation with fine friction particles to achieve optimal friction properties.

Features:

• High static friction coefficient
• Good abrasive resistance
• Self-cleaning capability
• Low abrasive interaction with the brake rotor material
• Up to 3 times longer operational life compared to organic and Kevlar composite materials

Application:

• Developed specifically for off-road motorcycles & ATVs
• Can be used on both front and rear brakes
• Could be used on the rear brake of road racing motorcycles

Operating Parameters:

• Specific pressure: 2.0 Mpa
• Sliding velocity: 20 m/s
• Constant maximum temp: 500°C
• Short time maximum temp: 750°C
• Counter-surfaces: steel disks

What is a sintered brake pad?

GOLDfren only manufacturers sintered brake pads that contain metal-ceramic and ceramic-carbon friction materials, these materials allow for less brake dust and a quieter braking experience. Sintered brake pads are made by fusing together metallic particles under high temperature and pressure which enhances friction properties and pad life, resulting in longer life and stronger braking. Sintered brake pads experience no brake fade when operating at high temperatures and in wet conditions. They also last up to 5 times longer than organic pads and provide additional braking strength. All materials used are environmentally friendly and do not contain any lead, asbestos, fibreglass or formaldehyde.

Reminder: one set of brake pads services one brake disc, if you are servicing multiple discs you will need multiple sets of brake pads.

100% brand new aftermarket tie rod only kit. Meets or exceeds OEM specs for fit and performance.

Brake shoes 

GOLDfren began manufacturing sintered disc brake pads for a wide range of off-road and road motorcycles in 1991, nearly three decades on from their first motorcycle brake pads GOLDfren has become one of the largest aftermarket manufacturers in the motorcycle brake disc pad industry. Their development of next-generation products has kept them at the technological forefront of Sintered Friction Braking providing you with confidence in the performance, durability and reliability of your brakes.

S3 Series:

The S3 sintered compound is optimal in dry and wet conditions for road & off-road motorcycles. For the road application, S3 pads are suitable for both the front and rear brake while on off-road applications the S3 is only recommended for the front brake. The S3 series is designed for low abrasive interaction with the rotor and quieter braking due to the ceramic composite material. It has an HH friction rating and performs better at higher temperatures than the AD compound. Friction materials contain metal-ceramic with a bronze-graphite and non-metallic friction additives are spread evenly on the base fine bronze body to achieve optimal friction properties.

Features:

• Very high static friction coefficient
• Minimal difference between wet and dry braking performance
• Good abrasive resistance
• Low abrasive interaction with the brake rotor material
• Longer life compared to organic and Kevlar composite materials

Application:

• For riders who demand a bit more than average from their bikes
• Recommended on both front and rear brakes (road application)
• Can also be used on the front brakes of off-road bikes and ATVs
• Works well on both dry and wet conditions

Operating Parameters:

• Specific pressure: 3.0 Mpa
• Sliding speed: 45 m/s
• Constant maximum temp: 450°C
• Short time maximum temp: 800°C
• Counter-surfaces: steel disks

What is a sintered brake pad?

GOLDfren only manufacturers sintered brake pads that contain metal-ceramic and ceramic-carbon friction materials, these materials allow for less brake dust and a quieter braking experience. Sintered brake pads are made by fusing together metallic particles under high temperature and pressure which enhances friction properties and pad life, resulting in longer life and stronger braking. Sintered brake pads experience no brake fade when operating at high temperatures and in wet conditions. They also last up to 5 times longer than organic pads and provide additional braking strength. All materials used are environmentally friendly and do not contain any lead, asbestos, fibreglass or formaldehyde.

Reminder: one set of brake pads services one brake disc, if you are servicing multiple discs you will need multiple sets of brake pads.

Fuel Pump Assembly by All Balls.

Features:

• Pump draws less current than OEM pump while maintaining the same flow rate at working pressure. This reduces working temperatures and increases life of the unit.
• Restore lost performance or non-functioning fuel pump with this economical solution.
• Includes all necessary parts to replace the fuel pump module (complete module, retaining nut and gasket).

Brake shoes 

Upgrade your motorcycle's clutch system with the All Balls Racing Motorcycle Clutch Cable. Designed with precision and durability in mind, this clutch cable delivers exceptional performance and reliability on the road.

• Black PVC outer jacket for maximum flexibility and durability.
• Steel inner casing that is tightly coiled for low compression.
• A pre-lubricated nylon inner sleeve guarantees smooth operation and long life.
• All wire ends are bird-caged prior to terminal casting for superior pull-out resistance.
• EPDM-moulded rubber components for high UV resistance and long life.
• Injected moulded components are manufactured from high-strength POM material.

DENALI Motorcycle Specific Fairing / Fender Mounts

Available for most ADV, Cruisers and Sport Touring Models Laser cut and powder coated steel brackets either position the lights in the optimum location just below to the outside of the headlight, or create a two-point fender mount strong enough to mount our largest lights to your fender.

Produced in the U.S.A. with the latest materials and technology in gasket production to Vertex specifications. Vertex gaskets ensure long-lasting performance and leak prevention for your rebuild needs.

• Ignition cover gasket
• Designed to fit O.E.M. cover

The popular Oxford HD chain lock is a fantastic mid-range lock which is light enough to be easily carried with you but still sufficiently secure to deter would-be thieves.

The HD Chain Lock comes with three keys and key replacement service. On receipt of your chain lock, note your key number and keep in a safe place. In the unfortunate event that you lose all your keys, a new spare can be made up for you.

Features:

• Hardened 9.5mm square link chain.
• Tough double locking padlock with hardened steel shackle which doubles as a disc lock.
• Key dust cover.
• Three keys.
• Key Replacement Service.
• ART 4114 approved
• Sold Secure Motor Scooter Silver approved.

Available in three lengths:

• OF157 1.0M
• OF159 1.5M
• OF160 2.0M

Quality design and construction of every All Balls piece meets the toughest standards and conditions - from daily commuting to full-on racing, all older bearing and seal designs are upgraded to the best and latest specs and designs.

One kit does it all! All of the bearings, seals, shafts*, bushings, and thrust bearings (if required) in one all-inclusive kit to do the job correctly and completely.

• All bearing shafts manufactured with 52100 bearing steel that is hardened and centerless ground for a precision fit and extended wear life.
• Steel spacers are case-hardened and plated for resistance to wear and corrosion.
• No more hunting around for missing pieces costing you time and extra money.
• Needle thrust bearings have been replaced with Teflon bearings. Designed to live longer in water and dirt.

* Not included in all kits.

Note: A limited number of kits only available with bearings and seals.

The Oxford Cable Lock is a self-coiling tensile steel cable lock.

The Oxford Cable Lock has a key replacement service. When you buy your Cable Lock, simply note down the number which comes attached to the keys on a metal tag. Keep this in a safe place, then in the event that you are unfortunate enough to lose all your keys, it will be possible to get a new key made up for you.

Features:

• Self-coiling high tensile steel cable with protective vinyl sleeve
• Complete with three keys
• Two quick release brackets
• Dimensions: 1.8m x 12mm cable
• Key dust cover included
• Available in 5 colors: Blue, Smoke, Clear, Gold, and Red

The Whites OEM replacement cast levers provide an economical alternative to original levers. The perfect spare to have ready in your workshop in case of race day disaster. Available in black and OEM silver finish (model dependent).

Features:

• Direct OEM replacement cast levers.
• Designed to exceed OEM specifications.
• Built to resist breakage.
• Designed to fit OEM perch.
• Made from die-cast aluminum for maximum durability and affordability.

NOTE: This Vertex Top End Gasket Set contains all components pictured.

Produced in the U.S.A. with the latest materials and technology in gasket production to Vertex specifications. Vertex gaskets ensure long-lasting performance and leak prevention for your rebuild needs. Vertex's replacement gaskets and seals are available as top-end kits, complete engine kits, or as an oil seal kit.

• These sets include the head, base, and exhaust gaskets, valve seals, O-rings and other gaskets to complete a top-end rebuild.

K&N off-road replacement air filters are ideal for extended use in dirty and dusty off-road riding and provide clean carburetion even at high altitude. Generally, no jet changes are required with just a K&N filter element. K&N replacement air filters are washable and reusable and provide high air-flow with excellent filtration.

Features

• Designed to provide increased horsepower and acceleration.
• Pleated cotton media provides a large filtration area offering low restriction, high-capacity and long service intervals.
• Multiple layers of woven cotton gauze media offer excellent filtration.
• Fits directly into OEM airbox with an application-specific sealing bead ensuring a precise fit.
• No fuel management modifications are required to obtain increased performance.
• Washable and reusable, most are pre-oiled and ready to ride.

Whites Cable range is designed to meet and exceed OEM specifications and quality at affordable pricing. Including Throttle, Clutch, Brake (front, rear and hand) and Speedo cable for your common farming/trail machines.

Using a black vinyl housing and inner nylon sleeve for longer life and smooth operation the Whites Throttle Cables are designed to be a long life replacement for your worn and degraded OEM cable. We have a comprehensive range of Throttle Cables for your AG, XLR, KL, DR and more agricultural based motorcycles.

Meets and exceed OEM quality cables
Black vinyl housing for cable protection
Inner nylon sleeve provides smooth operation and a long life
Designed to withstand the harsh life of a farm environment
Perfect fit for your DR/DF200

Whites extensive cable range specifically for agriculturally based motorcycles.

Produced in the U.S.A. with the latest materials and technology in gasket production to Vertex specifications. Vertex gaskets ensure long-lasting performance and leak prevention for your rebuild needs. Vertex's replacement gaskets and seals are available as top-end kits, complete engine kits, or as an oil seal kit.

• One kit containing all of the gaskets necessary to rebuild the water pump.
• Designed to fit O.E.M. water pump.