New Arrivals

Celebrate being part of the coolest family on earth with our collection of biker signs.

Whether you commute to work on a sensible 125, cross continents on a metal mule or tear up the weekend streets on your pride and joy... you belong.

With pre-drilled holes for mounting, our Garage Signs are also the perfect gift for the biker who's got it all!

Key Features
• Indoor use only
• Made from high quality coated metal tin plate with rolled edges
• 4 x 3.2mm pre-drilled holes for attachment
• Dimensions - 30 x 20cm x 0.25mm thick
• Weight - 124g

Up to 40% stronger than OE axles, these complete axles feature enlarged CV joints, bearing cages, and chromoly axle shafts. All internal components are precision ground and utilize molybdenum grease.

Features:

• 40% stronger than OEM.
• Larger 4340 chrome-moly steel axle bar.
• Precision ground components.
• Low profile clamps.
• Neoprene boots.
• Engineered in the USA.
• Manufactured in an ISO facility.
• Assembled with 3% moly grease.
• Black oxide coating to resist rust and corrosion.

NOTE: This Vertex Top End Gasket Set contains all components pictured.

Produced in the U.S.A. with the latest materials and technology in gasket production to Vertex specifications. Vertex gaskets ensure long-lasting performance and leak prevention for your rebuild needs. Vertex's replacement gaskets and seals are available as top-end kits, complete engine kits, or as an oil seal kit.

• These sets include the head, base, and exhaust gaskets, valve seals, O-rings and other gaskets to complete a top-end rebuild.

• For many uses around workshop, garage or home
• Ideal for general cleaning, polishing, detailing or wiping up water, oil, chemicals and mopping spillages.
• Composition: 80% polyester / 20% polyamide

Recommended use:

• Dry: Microfibre cloth uses static electricity to clean and polish glass, dash, instruments etc. without using any chemicals.
• Damp: to clean off stubborn marks leaving a streak-free finish, without using any chemicals.

OEM spacers typically wear out within a year of hard riding. The wheel spacers should be checked and replaced as needed with every bearing service. Water and dirt act as a grinding compound between the seal face and the mating surface of the spacer. Once the grooves are deep enough, the sealing surface is lost, allowing water and dirt to pass through and contaminate the bearing.

Wheel Spacer Kits are designed to restore the proper sealing surface between the wheel seal and spacer, helping protect wheel bearings from premature wear and failure. Manufactured to precise tolerances for a direct replacement fit, All Balls spacers provide a smooth, durable surface for the seal to run against, reducing the risk of contamination and extending bearing life. Ideal for routine maintenance or during wheel bearing replacement, a quality wheel spacer kit ensures reliable wheel performance in harsh riding conditions.

All Balls Fuel Pump Kits are designed to restore lost performance caused by a failing or non-functioning fuel pump. Each kit offers a plug-and-play solution for quick and easy replacement of your OEM fuel pump module.

Kit contents vary by application and may include components such as the pump, filter, hoses, clamps, and wiring harness. Some kits contain only core components like the pump and filter. Please refer to the product image and listing details for exact contents specific to your model.

Features:

• OEM replacement fuel pump kits.
• Plug-and-play installation.
• Contents vary by kit — check image and listing for details.

Quality 90-degree valve adaptor for tubeless valves.

See image for variations.

The Whites OEM replacement cast levers provide an economical alternative to original levers. The perfect spare to have ready in your workshop in case of race day disaster. Available in black and OEM silver finish (model dependent).

Features:

• Direct OEM replacement cast levers.
• Designed to exceed OEM specifications.
• Built to resist breakage.
• Designed to fit OEM perch.
• Made from die-cast aluminum for maximum durability and affordability.

Includes all necessary parts to replace OEM-style fuel mixture screw with an extended screw for easy tuning.Kit includes extended mixture screw, O-ring, spring and washer.

A short section of Nitromousse that increases the PSI feel and extend the lifetime of your Nitro Mousse. Available for multiple sizes of Platinum and Soft Nitro Mousse.

Spare part for Lift Table.

M7 NYLON 3stg PUSH RIVETS 17-5-10-7

10 Pack of three-stage removable, reusable, black nylon push rivets.

These are very common on Suzuki, Yamaha, Honda, and Kawasaki models. Also called sportbike fairing clips, plastic ATV fender rivets, or plastic motorcycle clips. These cost a bundle from the factory but our ten packs are so affordable.

Oxford's Comfy's are multi-functional neck and headwear. Perfect for breaking the wind and preventing sunburn on the back of your neck the Oxford Comfy's can be worn however you want including as a beanie, facemask, neck tube, bandana and more. They have a seam-free construction that improves comfort while also providing excellent moisture-wicking properties.

Features:

• Multifunctional head and neck wear
• Lightweight, breathable, wind-resistant
• Material: 100% Polyester Microfibre
• Seam-free for maximum comfort
• One size fits all
• CE certified protection against UV radiation (UPF 17)*
• Hand wash only
• 3 Comfys per pack, each one individually designed

You can wear a Comfy however you feel comfortable but here are a few of the many options:

• Beanie
• Face mask
• Neck tube
• Bandana
• Full-face balaclava
• Open face balaclava

XAM chain and sprocket kits are the perfect drive maintenance kit for your bike. The perfect alternative to expensive OEM replacements, it is designed to meet and exceed OEM specifications. Supplied in presentable packaging with a carry handle for convenient transportation.

Features:

• Includes strong and durable C49 high-carbon steel sprockets.
• Paired with a high-quality XAM chain.

The TTO Digital Temperature Gauge allows you to easily monitor your engine's temperature ensuring you that your engine is not overheating.

Features:

• Easy to read LCD display and an ultra-thin design.
• The LCD display lets you to easily view all gauge readings regardless of the angle or lighting conditions.
• Surface mount for easy install, comes with double sided VHB tape or can be bolted on
• -40°-300°C/575°F

What's in the box:

• TTO Temperature
• Screw Caps and VHB Tape
• CHT Temperature Sensor, 12mm CHT

Quality replacement components to rebuild one fuel tap. Improves service life and resistance to water and dirt.

Includes:

• Face screws
• Face gasket
• Wave washer
• Tank bolts
• Tank gasket
• O-rings

Includes all gaskets and o-rings necessary to complete a crank (bottom end) and piston (top end) rebuild. Competitive pricing, made to meet and exceed OEM quality and designed as a direct OEM replacement the Whites Complete Gasket Set is your one-stop shop for engine rebuilds.

• Designed for OEM replacement
• Made from high-quality materials
• Meet or exceed OEM specifications
• Competitive pricing

A short section of Nitromousse that increases the PSI feel and extend the lifetime of your Nitro Mousse. Available for multiple sizes of Platinum and Soft Nitro Mousse.

Having the ability to turn corners is pretty important, so tie rod ends play a large role in any vehicle's safety. Whites Tie Rod End Kits are the perfect replacement for your old and worn-out OE parts, or an excellent upgrade to your steering system.

To ensure a great fit we recommend using our fitments search, or referencing the fitments tab above.

• Steel and aluminium construction strengthened in critical areas for durability
• Affordable OEM replacement
• Mounts to your OEM Tie Rods

RMSTATOR is specialized in designing and manufacturing innovative electrical and electronic components for Powersports vehicles like motorcycles, ATV, SxS, UTV, snowmobiles, and PWC. Through unrelenting quality control, we ensure that each component meets or exceeds the OEM specs. With over 25 product families, rest assured that you will find the part you need.

• Direct replacement to your original unit.
• Plug-and-play, direct fit, easy installation.
• No assembly required
• Higher grade of electric components.
• Improved heat sink and charging capabilities
• The quality exceeds the OEM equipment

RM STATOR has even included the opposite connector (main harness side), as they know these are often melted/corroded/defective and a major cause for repetitive electrical issues.

Battery condition is extremely important. No voltage regulator can work correctly with a bad or weak battery. Always fully charge your battery before performing any charging system tests or replacing parts. If there is any doubt, have the battery load tested or replaced.

Please Note:

1. All electrical components must be fitted by a qualified technician.
2. Before fitting electrical components ensure the root cause of the original failure has been addressed.
3. The absence of either of points 1 or 2 above, will void any warranty.

Quality pair of fork oil seals from All Balls Racing.

Features:

• Dyno tested to last 3 to 4 times longer than OEM seals.
• Directional ribs on outside of seal allow seal to be installed easily.
• Dual-sealing lips guarantee oil stays in and dirt stays out.

NOTE: RIGHT RADIATOR ONLY, FOR LEFT SEE WPRAD075L FOR PAIR SEE WPRAD075P.

Whites aluminium radiators make great replacements to your bent, cracked, and damaged radiators. Whites radiators offer exceptional cooling and maximum efficiency to ensure your machine's top performance. Based on the OEM specs, a hand-welded aluminium design offers both a great fit and styling. All cap side radiators will include a new radiator cap.

Add a little extra style and functionality to your motorcycle with Whites quality products.

• Whites radiators offer exceptional cooling and maximum flow efficiency to ensure your machine’s top performance
• Utilizes stock mounting hardware (not included) for a great fit
• Hand welded aluminium design for a great look and functionality
• Includes a new radiator cap

GOLDfren began manufacturing sintered disc brake pads for a wide range of off-road and road motorcycles in 1991, nearly three decades on from their first motorcycle brake pads GOLDfren has become one of the largest aftermarket manufacturers in the motorcycle brake disc pad industry. Their development of next-generation products has kept them at the technological forefront of Sintered Friction Braking providing you with confidence in the performance, durability and reliability of your brakes.

S3 Series:

The S3 sintered compound is optimal in dry and wet conditions for road & off-road motorcycles. For the road application, S3 pads are suitable for both the front and rear brake while on off-road applications the S3 is only recommended for the front brake. The S3 series is designed for low abrasive interaction with the rotor and quieter braking due to the ceramic composite material. It has an HH friction rating and performs better at higher temperatures than the AD compound. Friction materials contain metal-ceramic with a bronze-graphite and non-metallic friction additives are spread evenly on the base fine bronze body to achieve optimal friction properties.

Features:

• Very high static friction coefficient
• Minimal difference between wet and dry braking performance
• Good abrasive resistance
• Low abrasive interaction with the brake rotor material
• Longer life compared to organic and Kevlar composite materials

Application:

• For riders who demand a bit more than average from their bikes
• Recommended on both front and rear brakes (road application)
• Can also be used on the front brakes of off-road bikes and ATVs
• Works well on both dry and wet conditions

Operating Parameters:

• Specific pressure: 3.0 Mpa
• Sliding speed: 45 m/s
• Constant maximum temp: 450°C
• Short time maximum temp: 800°C
• Counter-surfaces: steel disks

What is a sintered brake pad?

GOLDfren only manufacturers sintered brake pads that contain metal-ceramic and ceramic-carbon friction materials, these materials allow for less brake dust and a quieter braking experience. Sintered brake pads are made by fusing together metallic particles under high temperature and pressure which enhances friction properties and pad life, resulting in longer life and stronger braking. Sintered brake pads experience no brake fade when operating at high temperatures and in wet conditions. They also last up to 5 times longer than organic pads and provide additional braking strength. All materials used are environmentally friendly and do not contain any lead, asbestos, fibreglass or formaldehyde.

Reminder: one set of brake pads services one brake disc, if you are servicing multiple discs you will need multiple sets of brake pads.

The Whites OEM replacement cast levers provide an economical alternative to original levers. The perfect spare to have ready in your workshop in case of race day disaster. Available in black and OEM silver finish (model dependent) and constructed with a brass bushing for maximum performance with smooth operation.

Specifications:

• Direct OEM replacement cast levers.
• Designed to exceed OEM specifications.
• Built to resist breakage.
• Designed to fit OEM master cylinder.
• Made from die-cast aluminium for maximum durability and affordability.
• Constructed with brass bushing for maximum performance with smooth operation.

The Whites Independent Rear Suspension Knuckle Kits contain everything required to rebuild the rear knuckle.

• Needle bearing shafts are hardened steel.
• Self lubricating bushings for better wear resistance.
• All metal bushings are hardened to prevent wear.

IRS Knuckle Kits are model specific, it is recommended that you use our fitments search to ensure correct fit.

The Whites Independent Rear Suspension Knuckle Kit contains everything required to rebuild the rear knuckle on your ATV. The needle bearing shafts are constructed from hardened steel with self-lubricating bushings for excellent wear resistance, all included bushings are hardened and plated for durability and corrosion resistance. IRS Knuckle Kits are model specific, it is recommended that you use our fitments search to ensure correct fit.

Contains everything to rebuild the rear knuckle
Needle bearing shafts are constructed from hardened steel
Self-lubricating bushings for excellent wear resistance
Hardened metal bushings for wear prevention

The Whites OEM replacement cast levers provide an economical alternative to original levers. The perfect spare to have ready in your workshop in case of race day disaster. Available in black and OEM silver finish (model dependent).

Features:

• Direct OEM replacement cast levers.
• Designed to exceed OEM specifications.
• Built to resist breakage.
• Designed to fit OEM perch.
• Made from die-cast aluminum for maximum durability and affordability.

Fuel pump strainers act as a first line of defence against fuel system contamination. Strainers filter out common contaminants found in gasoline such as dirt, dust and other particulate matter, as well as gasoline varnish. Quantum fuel pump strainers feature multiple layers of strainer media to filter progressively smaller particle sizes. The expanded surface area provides enhanced filtration, extending the life of the fuel pump.

Restricted fuel flow through a clogged strainer causes the fuel pump to work harder, reducing pump longevity. Strainer clogging is among the top causes of fuel pump failure making it important to replace your strainer regularly - before problems arise. We recommend replacing fuel pump strainers in powersports applications once a year as part of a preventative maintenance plan.

Features:

• Designed with gradient density to meet or exceed OE specifications.
• Designed to ensure optimal filtration to prevent fuel system contamination.
• Strainer material tested and validated for capacity and efficiency by accredited third party.