Tools

Specifically designed for cable maintenance this simple tool directs fluid down the housing of the cable extending the life and performance of all wired cables. Dual screws ensure a tight seal and the anodised lightweight aluminium is strong and durable while providing a great look.

Features:

• Simplifies cable maintenance
• Dual screw for a tighter seal
• Easy to use
• Made of anodised aluminium

The Oxford Airflow Shock is a portable shock pump for topping up air pressure on MTB suspension forks and rear shocks, quickly delivering up to 300 psi capacity.

Features:

• Mechanical pressure gauge
• 6 Inch pivoting hose
• Precision alloy barrel
• Pressure release button
• Max inflation: 300 PSI

A 28-piece motorcycle tool kit. Ergonomically designed, the tools come with soft gel handles that are comfortable to use. The tools are made from high- quality carbon steel and come in a compact storage case. The case can be kept under your rear seat, it folds down to 18cm x 10.5cm x 4cm.

Features:

• 28-piece kit.
• Ergonomically designed.
• High-quality carbon steel construction.
• Compact storage case.

Includes:

• 10pc screwdriver bit set
• Extension bar
• 5pc hex key set (6mm, 5mm, 4mm, 3mm, 2mm)
• Wire cutters
• Screwdriver handle
• Needle nose pliers
• 5mm, 6mm, 7mm, 8mm, 9mm, 10mm and 11mm sockets
• 2 x electrical screwdrivers

9 Hex Key set.

Key Features
• 1.5, 2, 2.5, 3, 4, 5, 6, 8, 10mm Hex keys
• Ball end

Introducing our newest heavy-duty recall-type charging system upgrade kit for Aprilia 2009-2020 RSV4 & 2011-2020 Tuono V4.

Anyone who rides or repairs Aprilia’s motorcycles is probably familiar with the stator, flywheel, and sometimes voltage regulator issues common to these models. Most of these bikes will have had at least one stator fail in its lifetime so far. The main problem was extremely strong magnets were used on the original flywheels, creating a very high power stator output, which generated excessive heat. This usually resulted in burned-up, or shorted stator winding, and often in a failed voltage regulator.

The solution was a new flywheel from Kokusan with lower-strength magnets, dropping the stator output and heat generation. This results in a charging system output perfectly matched for the bike’s electronic needs and the long-term reliability of the stator and voltage regulator.

To prevent or correct the flywheel problems, our engineers at RMS Labs have come up with a completely reliable heavy-duty charging system replacement kit for your Aprilia. Upgrade today if you haven’t already!

Included in this kit

• Heavy-duty Kokusan brand recall-type OEM flywheel
• Triple-tested heavy-duty stator
• Mosfet voltage regulator rectifier
• Crankcase cover gasket
• Flywheel puller

With this kit, you will be able to upgrade your current failure-prone charging system with a heavy-duty version using the latest technologies

Features

• Kokusan upgrade/recall type flywheel: Lower-strength magnets for correct stator output, low heat generation, and long-term reliability.
• Built to OEM size: Fits precisely in your ride install it and forget it.
• Improved epoxy: Uses high-temperature epoxy that is stronger than OEM, eliminating the possibility of magnet detachment
• High-grade steel capping: Prevents harsh additives in motor oil from degrading the epoxy attaching the magnets. Though extremely unlikely, if a magnet did ever come loose, it would remain in the sleeve preventing contact with the stator.
• Precise balancing: Eliminates crankshaft vibrations for longer engine longevity.
• Shop with confidence: All products are tested. Don't waste time with temporary solutions, and start fixing your ride like a pro!

Specifications:

• Stator Dimensions
• Interior diameter: 43 mm
• Exterior diameter: 105 mm
• Thickness: 13.8 mm
• Length of wires stator to grommet: 125 mm
• Length of wires grommet to plug: 320 mm
• Other specifications:
• Number of wires: 3
• Number of plugs: 1
• Number of pins: 3
• Alternator:Yellow to Yellow = 0.3 ohms +-20%
• Flywheel Dimensions
• Exterior Diameter #1: 121 mm
• Exterior Diameter #2: 119 mm
• Interior Diameter: 107 mm
• Interior Diameter Center Housing: 19.2 mm
• Exterior Diameter Center Housing: 34 mm
• Thickness (exterior): 35.3 mm
• Thickness (interior): 30.65 mm
• Voltage Regulator Dimensions
• Width: 80 mm
• Length: 110 mm
• Height: 28 mm
• Wires length: 150 & 400 mm
• Fixation holes center to center: 80 mm
• Other specifications:
• Number of plugs: 2
• Number of pins: 7
• Number of wires: 7
• Minimum Charging Voltage: 14.5 V +- 0.5 V
• Maximum Charging Current: 50 A / 500 W
• Open Circuit Voltage: 15 V
• Operation Temperature: -20° C to 85° C
• Flywheel Puller Dimensions
• 36 mm x 1.5 right-hand male
• Length: 60 mm
• Exterior Diameter: 47 mm
• Interior Diameter: 20 mm
• Exterior Diameter Center Housing: 37 mm

Please note: There are two possible kits for the RSV4 engine. This kit ONLY fits RSV4 engine numbers HIGHER than 3413 with Kokusan flywheels. Please compare our flywheel to your original.

If your RSV4 engine number is LOWER than 3413, your motor uses the Mitsubishi flywheel and will need Stator Assembly 857201. Refer to kit RMS900104929.

Features:

• 2 Steel case and fascia ring.
• Tough acrylic window.
• Holds the peak pressure reading.
• Pressure bleeding button.
• Long 14/36cm flexible hose with a 360° swivelling angled head.
• Gauge unit protected in a rubber casing.
• 0 -60psi for motorcycles, cars, caravans, etc.

Having difficulty accessing your tyre valves? We’ve made it easy for you with our 90 degree clip-on valve extension. To make it even easier, we suggest attaching the chuck to your pump hose before attaching it to the tyre.

The MotoPressor Dial Tyre Gauge has an easy to read, 40mm dial with both PSI and Kpa graduations up to a maximum of 60PSI and 400Kpa.

This model has a straight stem and will hold the reading when removed from the valve stem, plus it has a bleeder/reset button.

We all know how hard it is to get those “straight” chucks onto our motorcycle tyres. This chuck will fit most air hoses. If it doesn't screw directly onto the hose you are using, you will have to buy an adapter available at most plumbing supplies.

Brand new aftermarket Stator + Red Machined Aluminum Mosfet Regulator Kit

• Direct replacement to your original unit
• Plug-and-play, direct fit, easy installation
• All products shipped are tested

All item pictures are accurate; if in doubt do not hesitate to compare our item to your original part.

Stator

• Highest-grade lamination materials
• Highest-grade copper windings, resistant to 200 degrees Celsius.
• Pick up pulsar coil included
• Connector included
• Rubber grommet included

Machined Aluminum Mosfet Regulator

Our new red machined aluminum Mosfet voltage regulator is a great upgrade for heat dissipation in any power sports charging system. After 10 minutes of use, our billet aluminum heatsink runs cooler by 33% than standard cast regulator housings. Our new red regulator, equipped with the renowned Mosfet regulation technology, is an added value to any three-phase permanent magnet charging system.

STOP BURNING YOUR REGULATOR RECTIFIER!
It is time to update or replace your voltage regulator with the advanced MOSFET type.
It runs cooler than all OEM diode-style regulators. In addition, this rectifier has to overheat protection, rather than burn up, it will simply turn off for a while and cool off.

• The quality exceeds the OEM equipment
• Improved heat sink and charging capabilities
• Higher-grade electric components

We have even included the opposite connector (main harness side) as we know these are often melted/ corroded/ defective and a major cause of repetitive electrical issues.

Why use Mosfet Enhanced technology?

• Runs cooler: Runs much cooler than the traditional Shunt voltage regulator rectifier.
• Saves gas: Less load on the stator, less work, less fuel is used and you save.
• Regulated energy: The power charging your battery is steadier and smooth
• Extended battery life: Extends the battery’s life and cold-cranking capacity
• More engine power: Removes stator load resulting in more engine power
• Optimized power: Optimize power delivery by switching the stator coils on or off.

Specifications:

• Dimensions Stator:
• Interior diameter: 42 mm
• Exterior diameter: 105 mm
• Thickness: 20 mm
• Length of wires stator to grommet: 160 mm
• Length of wires grommet to plug: 950 mm
• Length of pickup coil's wire to grommet: 90 mm
• Other specifications:
• Number of wires: 5
• Number of plugs: 3
• Number of pins: 5
• Wire-to-wire resistance:
• Alternator: White between each White = 0.6 ohms +-20%
• Pickup: Green to Blue = 500 ohms +-20%
• Dimensions Red Machined Aluminum Mosfet Regulator (CNC):
• Width: 103 mm
• Length: 103 mm
• Height: 28 mm
• Fixation holes center to center: 80 mm
• Other specifications:
• Number of plugs: 2
• Number of pins: 5
• Minimum Charging Voltage: 14.5 V +- 0.5 V
• Maximum Charging Current: 50 A / 500 W
• Open Circuit Voltage: 15 V
• Operation Temperature: -20°C to 85°C

The Torque Mighty 15 Folding Multi-Tool includes 15 chrome vanadium tools. It has laser-etched graphics and lightweight 6061 aluminium sides.

Key Features:

• 2, 2.5, 3, 4, 5, 6, 8mm Hex keys.
  
  
• T25 Torx key.
  
  
• No.2 Cross head screwdriver.
  
  
• No.5 Flat head screwdriver.
  
  
• Chain tool.
  
  
• 14G, 15G, 16G, Mavic M7 spoke keys.

Oxford's Oil Filter Wrench Strap is ideal for removing oil filters that have a diameter between 50-120mm?. By wrapping the strap around the oil filter and creating a tight fit, the torque from the applied pressure on the wrench helps to gradually loosen the oil filter.

Features:

• Fits oil filters 50-120mm.
• One-handed operation.
• Durable steel construction.
• Reinforced rubber strap.
• Non-slip and fully adjustable strap.
• Corrosion resistant handle.

• 36 mm x 1.5 right-hand male
• All products are tested

Multipack of absorbent Oxford Drip Pads.

Key Features
• Absorption pads for general purpose workshop use
• 0.5 litre absorption capacity for each pad
• Ideal for catching drips and soaking up spills under motorcycles, carsm, or any motorised vehicles
• Absorbs and retains oil and oil-based liquids such as engine/gearbox oil, fuel, and most brake fluids
• Hydrophobic, so can be used to clean up oil spills on water

Size: 39cm x 48cm

What's Included
• 4 x 2mm plastic-backed floor protection pads
• 4 x 5mm maximum absorption pads

Torque Long Handle Hex Key wrench.

Key Features
• Resin grip
• Ball end

The Acebikes BrakeFix is a clever device to lock the front brake for all types of motorbikes. The BrakeFix is wrapped around the brake lever and handlebar. It is easy to use, with a simple but secure click-to-lock system.

The Acebikes brake lever jammer BrakeFix is used to lock the front brake for any type of motorbike. It is easy to use, with a simple but secure click-to-lock system. BrakeFix is perfect for parking your bike on the road, especially on steep slopes or even mountain trails. The clever and durable construction ensures that, once fitted, your bike will be safe on any surface. BrakeFix is also ideal for transporting your bike on a trailer or in a van.

Features:

• Durable and extremely rigid material.
• Lightweight.
• Click to lock system.
• Suitable for every motorcycle.
• Adjustable into different positions.

MotoPressor Tyre Gauge now comes standard with two chucks. A straight chuck for "easy to get at" valve stems PLUS a 45° chuck for those "not so easy to get at" valve stems.

We all know what a pain Petrol Station gauges are. Most are woefully inaccurate and impossible to get onto a motorcycle valve stem. To use the MotoPressor Tyre Gauge with Petrol Station gauge, simply attach the MotoPressor Tyre Gauge to your valve stem, attach the petrol station chuck to the inline fitting on the gauge and get an instant and accurate reading in PSI or KPA.

No need to switch between the gauge and air compressor hose! Added a little too much air to your tyre? Simply press the air bleed button and adjust to your desired pressure.

NOTE: When swapping out the chuck, use plumbers tape on the hose thread. Wrap the thread, in a clockwise direction with 3 - 5 wraps of plumbers tape. Screw on the new chuck and tighten. Failure to follow these instructions will result in air leaks.

The Oxford Air Gauge gives a digital reading of your tyre pressure and is quick and easy to use.

Features:

• Reads a choice of pressure scales: PSI/BAR/kPa/KG/CM2.
• Digital readings.
• Automatic shut-off.
• Fits Schrader valves.
• Pressure range: 0 to 6.9 BAR. 0 to 100 PSI. 0 to 690 Kpa.
• Includes 4 x valve caps.
• 1 x CR2032 (3V) battery.

This premium jump starter pack offers power anywhere, anytime, ensuring that you are never left stranded. An important piece of emergency kit, it can start motorcycles, watercraft, ATV/UTV and petrol car engines up to 5.0L.

Features:

• Charges your phone or tablet: essential functionality when you need it most.
• Compact and portable: complete kit weighs just 715g and fits into a 184 x 140 x 70mm carry case.
• Powerful performance: 10,000mAh battery capacity with a 500A starting current.
• Ideal for road trips: reliable jump starter pack for emergency use on the go.

The MotoPressor Pencil Tyre Gauge provides accurate, dependable tyre pressure readings with an easy-to-read dual scale. The dual scale provides a reading for both Kg/cm² and PSI. To use, simply press the head onto any standard valve system, and allow the gauge to provide a reading.

Includes 2 combination valve cap and tyre valve removal tools.

The Whites 4-in-1 Hex Axle Tool is compatible with most late model sport and off-road motorcycles. The tool includes 17mm, 19mm, 22mm and 24mm sizes for quick and easy removal or installation of the axle. Manufactured from forged 7075-T6 aluminium for a lightweight design and enabling torque up to 90 foot-pounds.

• Forged 7075-T6 aluminium for a lightweight nature
• 17mm, 19mm, 22mm and 24mm hex sizes
• Capable of torquing to 90 foot-pounds
• Anodised finish
• Colour: Black

The Whites 4-in-1 Hex Axle Tool is compatible with most late model sport and off-road motorcycles. The tool includes 17mm, 19mm, 22mm and 24mm sizes for quick and easy removal or installation of the axle. Manufactured from forged 7075-T6 aluminium for a lightweight design and enabling torque up to 90 foot-pounds.

• Forged 7075-T6 aluminium for a lightweight nature
• 17mm, 19mm, 22mm and 24mm hex sizes
• Capable of torquing to 90 foot-pounds
• Anodised finish
• Colour: Black