HARD PARTS

Each bike manufacturer uses different connectors for their indicators. This means that when fitting universal aftermarket indicators you need to cut the original connectors off and replace them with bullet fittings.

Not any more! Simply connect the IndyLeads between the original connector and the universal connector. Simple.

2 pack for front OR rear.

Replacing the fuel tank seal or gasket is a vital part of the fuel pump replacement process. Quantum tank seals are made exclusively from Viton, which are impervious to ethanol and other chemicals that degrade conventional rubber over time. These OE replacements are designed for fitment on specific vehicles.

The Whites OEM replacement cast levers provide an economical alternative to original levers. The perfect spare to have ready in your workshop in case of race day disaster. Available in black and OEM silver finish (model dependent).

Features:

• Direct OEM replacement cast levers.
• Designed to exceed OEM specifications.
• Built to resist breakage.
• Designed to fit OEM perch.
• Made from die-cast aluminum for maximum durability and affordability.

Replacing the fuel tank seal or gasket is a vital part of the fuel pump replacement process. Quantum tank seals are made exclusively from Viton which are impervious to ethanol and other chemicals that degrade conventional rubber over time. These OE replacements are designed for fitment on specific vehicles.

K&N's high-flow air filters are available as a replacement for your stock motorcycle air filter element. They are custom-engineered to fit your specific application and are designed to provide low restriction and increased performance while providing excellent engine protection for your motorcycle.

Features:

• Designed to provide increased horsepower and torque.
• Pleated media provides a large filtration area, offering long service intervals.
• Multiple layers of woven cotton gauze media offer excellent filtration.
• Application-specific base seal and sealing bead.
• Made in the USA for over 40 years.
• Washable and reusable, pre-oiled and ready to ride!

Specifications:

• Filter Material: Cotton Gauze
• Washable: Yes
• Height: 127mm
• Outside Diameter: 114mm
• Flange Inside Diameter: 73mm
• Flange Length: 16mm
• Flange Type: Centred
• Filter Re-Oiling Amount: 23ml

HFP replacement fuel pumps, modules, assemblies, and kit components are designed to meet or exceed OEM specifications, and feature upgrades that improve on the OEM design. Upgraded polymers, brushes, and commutators ensure long life and durability in multiple fuel blends.

• OEM or better performance
• Polished corrosion-resistant case to help minimize seizing during non-operation
• Specifically designed for quiet operation
• Drop-in replacement
• Gradient density fuel strainer for superior contaminant filtration
• Patented check valve technology
• Compatible with modern ethanol-infused pump gasoline

A quality Steering Head Bearing kit from All Balls. Make your bike handle like new!

Features:

• Upgrade ball-type steering bearings to Heavy-Duty Tapered Bearings
• Higher torque load and better wear than OEM ball-style steering bearings.
• Each kit is complete with upper and lower bearing sets and seals.

This K&N racing air filter has just two layers of cotton to provide even lower air restriction than our replacement air filter for street vehicles. Unlike K&N replacement air filters, fuel management modifications will be necessary with this racing filter. K&N racing air filters are washable and reusable.

Features:

• Designed to increase horsepower and acceleration.
• Designed for racing and track applications, not for street use.
• Washable and reusable air filter.
• Low restriction.

Specifications:

• Filte Material: Cotton Gauze
• Washable: Yes
• Height: 89mm
• Inside Diameter: 114mm
• Outside Diameter: 149mm
• Filter Re-Oiling Amount: 22ml

If you've broken your mirrors, don't worry. We've got you covered with our range of OEM-style Whites Mirrors. The right-specific mirror offers an affordable solution when only one mirror needs replacing. Designed to meet or exceed OEM specifications, Whites Mirrors provide a high-quality, cost-effective alternative to your original mirrors. Available for most makes and models, we recommend using our fitment search to find the perfect mirror for your bike.

Features:

• OEM replacement part.
• OEM-styled.
• Competitive pricing.
• Right mirror only.

These Spoke Kits are designed for riders seeking great value for their money. Made from cost-effective high-carbon steel, these spokes are paired with square OE-type steel nipples. This combination ensures that these spokes deliver both an affordable price and reliable performance.

Features:

• Economically priced.
• Excellent value and performance.
• High carbon steel spokes.
• Steel OE-type nipples.
• Replacement nipples and spokes are available.

Note:

Spokes are designed to fit Whites and MTX Rims only; however, they can be used with OE rims with modification to allow the wider nipple to fit.

Quantum replacement fuel pumps, regulators, tank seals and strainers are designed to meet or exceed OEM specifications, and feature upgrades that improve on the OEM design. Upgraded polymers, brushes, and commutators ensure long life and durability in multiple fuel blends.

Features & Benefits

• OEM or better performance
• Polished corrosion-resistant case to help minimize seizing during non-operation
• Specifically designed for quiet operation
• Drop-in replacement
• Gradient density fuel strainer for superior contaminant filtration
• Patented check valve technology
• Compatible with modern ethanol-infused pump gasoline

Kit contains all of the components to re-seal leaking master cylinders. Includes copper washers, spring, snap ring, replacement screws where applicable, cup seals, boot, and O-rings.

RMSTATOR is specialized in designing and manufacturing innovative electrical and electronic components for Powersports vehicles like motorcycles, ATV, SxS, UTV, snowmobiles, and PWC. Through unrelenting quality control, we ensure that each component meets or exceeds the OEM specs. With over 25 product families, rest assured that you will find the part you need.

• Direct replacement to your original unit
• Plug-and-play, direct fit, easy installation
• Highest grade of lamination materials
• Highest grade of copper winding, resistant to 200 degrees Celsius
• Connector included

Battery condition is extremely important. No stator can work correctly with a bad or weak battery. Always fully charge your battery before performing any charging system tests or replacing parts. If there is any doubt, have the battery load tested or replaced.

Dimensions:

• Interior diameter: 41mm
• Exterior diameter: 114mm
• Thickness: 22mm
• Length of wires stator to grommet: 160mm

Other specifications:

• Number of wires: 3
• Number of plugs: 1
• Number of pins: 3

Wire to wire resistance:

• Alternator: Yellow between each Yellow = 0.4ohms +/-20%

Please Note:

1. All electrical components must be fitted by a qualified technician.
2. Before fitting electrical components ensure the root cause of the original failure has been addressed.
3. The absence of either of points 1 or 2 above, will void any warranty.

P SERIES - Street Bikes

Premier's most successful general use material, our P series pads, are a tough Kevlar based organic material giving superb brake effect on all sportbikes and cruisers. This material is preselected by the catalogue when you order P prefix disc pads.

P SERIES - Off-Road

Part numbers relating to off-road machines are supplied in carbon graphite compound for medium durability, good brake effect and minimum heat generation.

The Whites OEM replacement cast levers provide an economical alternative to original levers. The perfect spare to have ready in your workshop in case of race day disaster. Available in black and OEM silver finish (model dependent).

Features:

• Direct OEM replacement cast levers.
• Designed to exceed OEM specifications.
• Built to resist breakage.
• Designed to fit OEM perch.
• Made from die-cast aluminum for maximum durability and affordability.

The Whites OEM replacement cast levers provide an economical alternative to original levers. The perfect spare to have ready in your workshop in case of race day disaster. Available in black and OEM silver finish (model dependent).

Features:

• Direct OEM replacement cast levers.
• Designed to exceed OEM specifications.
• Built to resist breakage.
• Designed to fit OEM perch.
• Made from die-cast aluminum for maximum durability and affordability.

The Whites OEM replacement cast levers provide an economical alternative to original levers. The perfect spare to have ready in your workshop in case of race day disaster. Available in black and OEM silver finish (model dependent).

Features:

• Direct OEM replacement cast levers.
• Designed to exceed OEM specifications.
• Built to resist breakage.
• Designed to fit OEM perch.
• Made from die-cast aluminum for maximum durability and affordability.

Replacement grip in sleek black, designed specifically for your Pro Adventure HotGrips®. Need to switch out that grip? This one's got you covered, ensuring your HotGrips® are ready to tackle any adventure that comes your way.

Quality replacement components to rebuild one fuel tap. Improves service life and resistance to water and dirt.

Includes:

• Face screws
• Face gasket
• Wave washer
• Tank bolts
• Tank gasket
• O-rings

The Whites OEM replacement cast levers provide an economical alternative to original levers. The perfect spare to have ready in your workshop in case of race day disaster. Available in black and OEM silver finish (model dependent).

Features:

• Direct OEM replacement cast levers.
• Designed to exceed OEM specifications.
• Built to resist breakage.
• Designed to fit OEM perch.
• Made from die-cast aluminum for maximum durability and affordability.

Having the ability to turn corners is pretty important, so tie rod ends play a large role in any vehicle's safety. Whites Tie Rod End Kits are the perfect replacement for your old and worn out OE parts, or an excellent upgrade to your steering system.

To ensure a great fit we recommend using our fitments search, or referencing the fitments tab above.

Steel and aluminium construction strengthened in critical areas for durability
Affordable OEM replacement
Mounts to your OEM Tie Rods

Kit Includes:
1 left-hand threaded tie rod end
1 lock nut
1 lock nut pin

The Whites OEM replacement cast levers provide an economical alternative to original levers. The perfect spare to have ready in your workshop in case of race day disaster. Available in black and OEM silver finish (model dependent).

Features:

• Direct OEM replacement cast levers.
• Designed to exceed OEM specifications.
• Built to resist breakage.
• Designed to fit OEM perch.
• Made from die-cast aluminum for maximum durability and affordability.

NOTE: LEFT RADIATOR ONLY, FOR RIGHT SEE WPRAD074R FOR PAIR SEE WPRAD074P.

Whites aluminium radiators make great replacements to your bent, cracked, and damaged radiators. Whites radiators offer exceptional cooling and maximum efficiency to ensure your machine's top performance. Based on the OEM specs, a hand-welded aluminium design offers both a great fit and styling. All cap side radiators will include a new radiator cap.

Add a little extra style and functionality to your motorcycle with Whites quality products.

• Whites radiators offer exceptional cooling and maximum flow efficiency to ensure your machine’s top performance
• Utilizes stock mounting hardware (not included) for a great fit
• Hand welded aluminium design for a great look and functionality
• Includes a new radiator cap

All Balls Choke Plunger Kit

- Choke plunger rebuild kits are intended to be used as a repair kit only.
- Kit contents will vary and may include o-rings, springs, retaining nuts, boots and cable guides as necessary.
- Choke plungers can seize or can easily be lost during a carburetor rebuild.
- Improperly functioning parts can cause hard starting or poor running conditions.
- Models with multiple carburetors include components to repair each choke plunger.

The new multi-density grips feature large soft diamonds to provide ultimate feel, comfort and grip.

The cushioning material is strategically placed along the shaft of the grip in the form of squishy diamonds. The additional cushioning offers excellent dampening against vibration and hand fatigue.

The multi-diamond design is one of the most popular MX grips styles. Why? Because the unique traction pattern of both large and small soft gel-like diamonds maximizes comfort and grip, thus improving feel and reducing rider fatigue.

Features:

• Dual-compound design for increased durability.
• Gel tack surface designed to offer exceptional grip.
• Diamond design helps reduce hand and arm fatigue and blisters.
• Full large and small diamond pattern.