New Arrivals

Quantum replacement fuel pumps, modules, assemblies, and kit components are designed to meet or exceed OEM specifications and feature upgrades that improve on the OEM design. Upgraded polymers, brushes, and commutators ensure long life and durability in multiple fuel blends.

Features:

• OEM or better performance.
• Polished corrosion-resistant case to help minimise seizing during non-operation.
• Specifically designed for quiet operation.
• Drop-in replacement.
• Gradient density fuel strainer for superior contaminant filtration.
• Patented check valve technology.
• Compatible with modern ethanol-infused pump gasoline.

Brand new external ignition coil.

Features:

• Direct replacement of your original unit.
• Plug-and-play, direct fit, easy installation.
• Highest grade lamination materials.
• Spark plug cap(s) included.
• All products shipped are tested.

Specifications:

• Width: 34 mm
• Length: 45 mm
• Height: 70 mm
• Wires length: 450 mm / 210 mm
• Fixation holes centre to centre: 56 mm
• Primary Resistance: 5.0k ohms
• Secondary Resistance: 0.8 ohms

*The image shown is for illustrative purposes only. Actual product colour may vary. Depending on availability and model, the item may be supplied in blue or black. Product specifications and quality remain the same regardless of colour. If in doubt, do not hesitate to compare our item to your original part.

Brand new aftermarket voltage regulator rectifier.

Features:

• Direct replacement to your original unit.
• Plug-and-play, direct fit, easy installation.
• No assembly required.
• Higher grade of electric components.
• The quality exceeds the OEM equipment.
• All products shipped are tested.

We have even included the opposite connector (main harness side) as we know these are often melted/corroded/defective and a major cause for repetitive electrical issues.

Specifications:

Dimensions:

• Width: 41mm
• Length: 50mm
• Height: 27mm

Other specifications:

• Number of plugs: 1
• Number of pins: 4
• Minimum Charging Voltage: 14.5 V +/- 0.5 V
• Maximum Charging Current: 20 A / 150 W
• Open Circuit Voltage: < 15 V
• Operation Temperature: -20°C to 85°C

Brand new Starter Relay Solenoid Switch. The quality exceeds the OEM equipment.

All item pictures are accurate; if in doubt, do not hesitate to compare our item to your original part.

Specifications:

Dimensions

• Height: 51mm
• Length: 46mm
• Width: 33mm

Other specifications:

• Number of terminals: 4
• Number of plugs: 1

Most riders take an enormous amount of pride in their bikes making sure they are clean and well maintained. Mint Silicone Detailer is specially formulated to give your bike a great shine and super smooth surface.

Mint Silicone Detailer is an innovative blend of oils which hides minor blemishes on surfaces, reducing the appearance of small cracks and scratches. Quick and easy to apply, it also provides a protective layer to surfaces and reduces the possibility of finger prints and other smudges appearing.

Key Features
• Easy application.
• Reduces friction on moving parts.
• Helps reduce cleaning.
• Stays looking clean for longer.
• Safe on painted surfaces.
• Clean, minty scent.
• Not tested on animals.

Great For:
• Paintwork
• Petrol tanks
• Carbon fibre
• Fairings

Cleaning power your pride and joy deserves.

• Ideal for removing stubborn rim tape glue and sealant residue
• Suitable on painted surfaces, rubber and plastic
• Perfect for removing sticker adhesive
• Fast acting formulation
• Mint scented
• Not tested on animals

Specially formulated with a high anti-corrosion content and a film-forming wax with a resin binder to improve durability and performance in very wet conditions. PTFE content fills the gaps between moving parts to reduce dirt ingress.

Features:

• Developed to deal with the most inclement weather conditions.
• Long-lasting protection with PTFE.

Great for:

• Chains
• Sprockets
• O, X, Z rings

Heavy-gauge stainless steel quick mounts bolt onto the bike, keeping straps away from hot exhaust headers, shortening straps lengths for maximum stability and speeding the installation of Giant Loop Saddlebags, Panniers, Dry Bags and Tank Bags. These handy mounts work on virtually any vehicle: motorcycles, snowmobiles, snow bikes, ATVs, UTVs, SxS, 4x4s – even boats!

• Dimensions: 1.75″ wide x 2.5″ long
• Slot width: 1-1/8″ (fits 1″ webbing)
• Hole: 10mm

NOTE: Not recommended for 2017-2021 KTM/Husqvarna 250-500cc models. The bolt location can lead to straps ripping and wear on your riding boots..

Genuine replacement visor for the LS2 FF807 Dragon and FF817 Challenger II helmet.

Features:

• Anti-scratch and UV-resistant.
• Easy visor locking and quick-release system.
• Pinlock-ready.

Genuine replacement visor for the LS2 FF807 Dragon and FF817 Challenger II helmet.

Features:

• Anti-scratch and UV-resistant.
• Easy visor locking and quick-release system.
• Pinlock-ready.

Yamaha exhaust pipe springs are 80mm in length, and made from zinc-plated steel. Sold in bags of 4.

Made in California, USA.

The Buckin’ Roll is a slim, trim, minimalist tank bag designed to keep essentials close at hand while out of the way when riding the most technical singletrack. This easy-to-mount tank bag features fully welded construction with waterproof coated materials and provides 1.5 litres of packable volume for carrying a smartphone, wallet, snacks, smaller tools, or an extra pair of gloves.

An integrated, clear smartphone pocket in the lid with electronics cable pass-through enables on-bike charging and power inside the bag. For those searching for the perfect tank bag for aggressive trail riding where quick, easy access to items is a priority, the Buckin’ Roll is the ideal choice.

Compact and Efficient: The Buckin’ Roll Tank Bag provides 1.5 litres of packable volume, perfect for essentials without crowding the tank area.

Ultra-Lightweight: Weighing just 1.1 lbs, it adds minimal weight to the bike, enhancing handling and comfort.

Rugged and Water-Resistant: Made from durable materials, the bag is designed to withstand the elements, keeping contents safe from water and dust.

Features:

• Easy Access: Keeps essentials handy when in the seat position and out of the way when standing on the footpegs.
• Waterproof Phone Pocket: Waterproof clear smartphone pocket with electronics cable pass-through enables on-bike charging and power inside the bag.
• Easy Mounting: Mounts behind gas cap for easy fueling.
• Fast Detaching: Unzips from the harness to keep valuables with you when away from the bike.

Specifications:

• Volume: 1.5 litres
• Dimensions:
  • Tank Bag: 4” L x 7” W x 4” H (10 cm L x 18 cm W x 10 cm H)
  • Smartphone Pocket: 7” L x 4” W (18 cm x 10 cm)
  • Harness: 7” L x 4” W (18 cm x 10 cm)
• Dry Weight: 0.66 lbs (0.3 kg)
• Materials: Rugged Bomb Shell™ coated fabric construction with radio-frequency (RF) welded seams, reflective trim, rugged fasteners including YKK zippers, nylon webbing, and Duraflex buckles.

Rough riding calls for stronger axles and that’s where All Balls Racing excels. Machined for exact OEM fit, the shaft is made of chromoly steel with a larger diameter than most axles. The axle has 6 ball bearings in each CV joint. Laminate coating resists corrosion and rust and protects axles from dirt, water, rocks and grease. Waterproof neoprene boots act as a first line of defence, shielding vulnerable joints and preventing leaks. High-performance molybdenum grease reduces heat and friction.

In static torsion trials, these axles were up to 30% stronger than OEM and aftermarket competition.

Features:

• 40% stronger than OEM.
• Larger 4340 chrome-moly steel axle bar.
• Precision ground components.
• Low profile clamps.
• Lasts approximately 50 percent longer than many aftermarket competitors.
• Neoprene boots.
• Typically runs almost 130,000 cycles versus 80,000 cycles for many axles.
• Engineered in the USA.
• Manufactured in an ISO facility.Assembled with 3% molybdenum grease.

Rough riding calls for stronger axles and that’s where All Balls Racing excels. Machined for exact OEM fit, the shaft is made of chromoly steel with a larger diameter than most axles. The axle has 6 ball bearings in each CV joint. Laminate coating resists corrosion and rust, and protects axle from dirt, water, rocks and grease. Waterproof neoprene boots act as a first line of defense, shielding vulnerable joints and preventing leaks. High-performance molybdenum grease reduces heat and friction.

In static torsion trials, these axles were up to 30% stronger than OEM and aftermarket competition. Lasts approximately 50 percent longer than many aftermarket competitors. Typically runs almost 130,000 cycles versus 80,000 cycles for many axles.

Features:

• 40% stronger than OEM.
• Larger 4340 chrome-moly steel axle bar.
• Precision ground components.
• Low profile clamps.
• Neoprene boots.
• Engineered in the USA.
• Manufactured in an ISO facility.
• Assembled with 3% molybdenum grease.

Rough riding calls for stronger axles and that’s where All Balls Racing excels. Machined for exact OEM fit, the shaft is made of chromoly steel with a larger diameter than most axles. The axle has 6 ball bearings in each CV joint. Laminate coating resists corrosion and rust and protects axles from dirt, water, rocks and grease. Waterproof neoprene boots act as a first line of defence, shielding vulnerable joints and preventing leaks. High-performance molybdenum grease reduces heat and friction.

In static torsion trials, these axles were up to 30% stronger than OEM and aftermarket competition.

Features:

• 40% stronger than OEM.
• Larger 4340 chrome-moly steel axle bar.
• Precision ground components.
• Low profile clamps.
• Lasts approximately 50 percent longer than many aftermarket competitors.
• Neoprene boots.
• Typically runs almost 130,000 cycles versus 80,000 cycles for many axles.
• Engineered in the USA.
• Manufactured in an ISO facility.Assembled with 3% molybdenum grease.

High-quality tie rod ends designed to work with original equipment tie rods.

Features:

• Rack kit contains tie rod end and shaft that connects to the steering rack as well as the outer tie rod end, boot and the required hardware for one side.
• Boot kit includes both right and left tie rod boots.

Rough riding calls for stronger axles and that’s where All Balls Racing excels. Machined for exact OEM fit, the shaft is made of chromoly steel with a larger diameter than most axles. The axle has 6 ball bearings in each CV joint. Laminate coating resists corrosion and rust and protects axles from dirt, water, rocks and grease. Waterproof neoprene boots act as a first line of defence, shielding vulnerable joints and preventing leaks. High-performance molybdenum grease reduces heat and friction.

In static torsion trials, these axles were up to 30% stronger than OEM and aftermarket competition.

Features:

• 40% stronger than OEM.
• Larger 4340 chrome-moly steel axle bar.
• Precision ground components.
• Low profile clamps.
• Lasts approximately 50 percent longer than many aftermarket competitors.
• Neoprene boots.
• Typically runs almost 130,000 cycles versus 80,000 cycles for many axles.
• Engineered in the USA.
• Manufactured in an ISO facility.Assembled with 3% molybdenum grease.

Whites Spoke Kits are crafted for riders who want high quality at an affordable price. Constructed from durable high-carbon steel, these spokes are paired with OE-type square steel nipples, delivering both cost-effectiveness and the trusted performance that Whites is known for.

Features:

• Steel OE-type nipples.
• Fitments available to suit most popular late model off-road motorcycles.
• Economically priced.
• Excellent value and performance,
• Compatible with OEM hubs and rims
• Supplied with OEM size (7mm) spoke nipples*

Note:

• *Oversize 8mm spoke nipple sets are available for separate purchase if required.
• If you are lacing an aftermarket rim to your hub assembly, please check the aftermarket rim's spoke nipple hole size. Many aftermarket rims require a larger (8mm) spoke nipple size.
• Whites recommends wheel building is performed by a suitably qualified professional.

Contains 10 flange bolts in factory style and finish.

Made in California, USA.

This vehicle-specific driving light mount allows you to mount any DENALI driving light to your R1300GS Adventure. Its low profile and tucked-in design make for a very clean install while placing your lights in the optimum location.

This kit includes beefy powder-coated steel brackets with an M8 mounting hole and all necessary mounting hardware.

What's In The Box

• (x2) Light Mounts
• Mounting Hardware

Rough riding calls for stronger axles and that’s where All Balls Racing excels. Machined for exact OEM fit, the shaft is made of chromoly steel with a larger diameter than most axles. The axle has 6 ball bearings in each CV joint. Laminate coating resists corrosion and rust and protects axles from dirt, water, rocks and grease. Waterproof neoprene boots act as a first line of defence, shielding vulnerable joints and preventing leaks. High-performance molybdenum grease reduces heat and friction.

In static torsion trials, these axles were up to 30% stronger than OEM and aftermarket competition.

Features:

• 40% stronger than OEM.
• Larger 4340 chrome-moly steel axle bar.
• Precision ground components.
• Low profile clamps.
• Lasts approximately 50 percent longer than many aftermarket competitors.
• Neoprene boots.
• Typically runs almost 130,000 cycles versus 80,000 cycles for many axles.
• Engineered in the USA.
• Manufactured in an ISO facility.Assembled with 3% molybdenum grease.

Up to 40% stronger than OE axles, these complete axles feature enlarged CV joints, bearing cages, and chromoly axle shafts. All internal components are precision ground and utilize molybdenum grease.

Features:

• 40% stronger than OEM.
• Larger 4340 chrome-moly steel axle bar.
• Precision ground components.
• Low profile clamps.
• Neoprene boots.
• Engineered in the USA.
• Manufactured in an ISO facility.
• Assembled with 3% moly grease.
• Black oxide coating to resist rust and corrosion.

This rear-visibility bundle is the ultimate solution for making you more visible to other motorists in daytime or nighttime conditions. The bundle includes a pair of rear switchback T3 turn signals, a universal license plate mount, and a plug-and-play wiring harness for effortless connection to your bike via our CANsmart controller.

The T3 switchback signal pods have a red running light, super bright red brake light, but switch to a bright amber LED signal light in sync with your factory turn signals. All T3 functions are ECE compliant and are guaranteed to help you stand out!

This bundle is designed to connect to a CANsmart controller, which is sold separately.

Bundle Contents:

• (1x) T3 Modular Switchback Signal Pods - Rear
• (1x) License Plate Mount - For T3 Signal Pods
• (1x) CANsmart Wiring Harness for T3 Switchback Signals

Note: Product bundles ship complete in a white box and will only show in stock if all components are available. All bundle components are also available for individual sale.

High-quality tie rod ends designed to work with original equipment tie rods.

Features:

• Rack kit contains tie rod end and shaft that connects to the steering rack as well as the outer tie rod end, boot and the required hardware for one side.
• Boot kit includes both right and left tie rod boots.

Rough riding calls for stronger axles and that’s where All Balls Racing excels. Machined for exact OEM fit, the shaft is made of chromoly steel with a larger diameter than most axles. The axle has 6 ball bearings in each CV joint. Laminate coating resists corrosion and rust and protects axles from dirt, water, rocks and grease. Waterproof neoprene boots act as a first line of defence, shielding vulnerable joints and preventing leaks. High-performance molybdenum grease reduces heat and friction.

In static torsion trials, these axles were up to 30% stronger than OEM and aftermarket competition.

Features:

• 40% stronger than OEM.
• Larger 4340 chrome-moly steel axle bar.
• Precision ground components.
• Low profile clamps.
• Lasts approximately 50 percent longer than many aftermarket competitors.
• Neoprene boots.
• Typically runs almost 130,000 cycles versus 80,000 cycles for many axles.
• Engineered in the USA.
• Manufactured in an ISO facility.Assembled with 3% molybdenum grease.

Rough riding calls for stronger axles and that’s where All Balls Racing excels. Machined for exact OEM fit, the shaft is made of chromoly steel with a larger diameter than most axles. The axle has 6 ball bearings in each CV joint. Laminate coating resists corrosion and rust and protects axles from dirt, water, rocks and grease. Waterproof neoprene boots act as a first line of defence, shielding vulnerable joints and preventing leaks. High-performance molybdenum grease reduces heat and friction.

In static torsion trials, these axles were up to 30% stronger than OEM and aftermarket competition.

Features:

• 40% stronger than OEM.
• Larger 4340 chrome-moly steel axle bar.
• Precision ground components.
• Low profile clamps.
• Lasts approximately 50 percent longer than many aftermarket competitors.
• Neoprene boots.
• Typically runs almost 130,000 cycles versus 80,000 cycles for many axles.
• Engineered in the USA.
• Manufactured in an ISO facility.Assembled with 3% molybdenum grease.

Up to 40% stronger than OE axles, these complete axles feature enlarged CV joints, bearing cages, and chromoly axle shafts. All internal components are precision ground and utilize molybdenum grease.

Features:

• 40% stronger than OEM.
• Larger 4340 chrome-moly steel axle bar.
• Precision ground components.
• Low profile clamps.
• Neoprene boots.
• Engineered in the USA.
• Manufactured in an ISO facility.
• Assembled with 3% moly grease.
• Black oxide coating to resist rust and corrosion.

Rough riding calls for stronger axles and that’s where All Balls Racing excels. Machined for exact OEM fit, the shaft is made of chromoly steel with a larger diameter than most axles. The axle has 6 ball bearings in each CV joint. Laminate coating resists corrosion and rust and protects axles from dirt, water, rocks and grease. Waterproof neoprene boots act as a first line of defence, shielding vulnerable joints and preventing leaks. High-performance molybdenum grease reduces heat and friction.

In static torsion trials, these axles were up to 30% stronger than OEM and aftermarket competition.

Features:

• 40% stronger than OEM.
• Larger 4340 chrome-moly steel axle bar.
• Precision ground components.
• Low profile clamps.
• Lasts approximately 50 percent longer than many aftermarket competitors.
• Neoprene boots.
• Typically runs almost 130,000 cycles versus 80,000 cycles for many axles.
• Engineered in the USA.
• Manufactured in an ISO facility.Assembled with 3% molybdenum grease.

Will help extend the life of your prized possession. Innovative design, rugged dependability, and superior function. Constructed from quality materials that meet or exceed OEM specifications.