HARD PARTS

A quality pair of fork oil and dust seals from All Balls Racing.

Features:

• Dyno tested to last 3 to 4 times longer than OEM seals.
• Directional ribs outside of the seal allow easy installation.
• Dual-sealing lips guarantee oil stays in and dirt stays out.

Upgrade rubber bushings found in Utility ATV A-Arms to AB's redesigned HD Delrin bushings.
This kit is designed to replace worn out rubber bushings and provides greater suspension travel and performance.
Quality design and construction of every All Balls piece meets the toughest standards and conditions - from daily commuting to full-on racing, all older bearing and seal designs are upgraded to the best and latest specs and designs.

Built with advanced Graphene Super Power Technology, these batteries are specifically designed for electric motorcycles, providing 20% more power and 30% longer lifespan. Engineered for high performance, they’re ideal for cold weather with exceptional reliability and durability.

Features:

• Graphene' Super Power.
• Super Power - 20% more power
• Longer lifecycle - 30% longer.
• Long Lasting in cold weather - 20% longer

PR SERIES – Off-Road Sintered

Premier PR pads have been upgraded to a new HIGH DENSITY sintered metal compound suitable for all types of moto-x and ATV use.

RMSTATOR is specialized in designing and manufacturing innovative electrical and electronic components for Powersports vehicles like motorcycles, ATV, SxS, UTV, snowmobiles, and PWC. Through unrelenting quality control, we ensure that each component meets or exceeds the OEM specs. With over 25 product families, rest assured that you will find the part you need.

• Direct replacement to your original unit
• Plug-and-play, direct fit, easy installation
• Highest grade of lamination materials
• Highest grade of copper winding, resistant to 200 degrees Celsius
• Connector included

Battery condition is extremely important. No stator can work correctly with a bad or weak battery. Always fully charge your battery before performing any charging system tests or replacing parts. If there is any doubt, have the battery load tested or replaced.

Please Note:

1. All electrical components must be fitted by a qualified technician.
2. Before fitting electrical components ensure the root cause of the original failure has been addressed.
3. The absence of either of points 1 or 2 above, will void any warranty.

Bolt brand bolts, nuts and washers meet all OEM standards. Designed with precision, each bolt comes in a convenient pack of 10.

P SERIES - Street Bikes

Premier's most successful general use material, our P series pads, are a tough Kevlar based organic material giving superb brake effect on all sportbikes and cruisers. This material is preselected by the catalogue when you order P prefix disc pads.

P SERIES - Off-Road

Part numbers relating to off-road machines are supplied in carbon graphite compound for medium durability, good brake effect and minimum heat generation.

Upgrades rubber bushings found in Utility ATV A-Arms to ABs redesigned HD Delrin bushings. Designed to replace worn-out rubber bushings and provide greater suspension travel and performance.

Got an accessory socket on your bike and want to connect a device with an SAE fitting like a MotoPressor Pocket Pump? This clever adaptor comes with a male lighter fitting that will fit BOTH car and motorcycle lighter sockets.

To plug into a motorcycle-style (Hella) socket, simply remove the RED adaptor at the front of the plug and plug straight into the motorcycle socket. To plug into a car socket, leave the RED adaptor in. Now you can use your MotoPressor Pocket Pump on both your bike and car.

Each pack of Premier CSK Clutch Springs contains a complete set of heavy-duty springs. Up to 15% stronger than the original.

Customer should be advised that after installation of a CSK kit the clutch lever will feel slightly ‘heavier’ than standard

Wrench Rabbit Rebuild Kits have been rebranded to Vertex Rebuild Kits; all components remain unchanged however you may receive a kit that is boxed differently to the one pictured.

Vertex Complete Engine Rebuild Kits are a simple and cost-effective way to complete a top-to-bottom professional rebuild for your 2 or 4-stroke motorcycle or ATV/UTV. The one easy to order kit will not only save you time by offering a one-stop-shop in a box, but they also save you money when compared to purchasing all items individually.

Vertex kits include quality components from Vertex, Hot Rods & Hot Cams.*

All parts are manufactured in the USA from the highest quality material.

Features:

• Crafted to deliver unbeatable levels of quality
• High-grade materials for exceptional performance
• Superior in durability and reliability
• Kits available for many 2 & 4-stroke motorcycles, ATVs & UTVs
• Cost-effective solution
• Saves time sourcing individual components
• Vertex pistons & gaskets*
• Hot Rods crank & bearing kits*
• Hot Cams cam chain*

Includes:

• Crankshaft
• Piston Kit
• Complete Engine Gasket Kit
• Oil Seal Kit
• Main Bearing and Seal Kit
• Water Pump Rebuild Kit
• Transmission Bearing Kit
• Countershaft Bushing/Seal Kit
• Cam Chain

*Specific parts vary by kit (see included parts above).

All Balls now offers a complete fork bush kit solution. The kit includes the following products:

• 2x slider bushings
• 2x leg bushings
• All copper washers and O-rings, 2 fork seal snap rings.

Quality design and construction of every All Balls piece meets the toughest standards and conditions — from daily commuting to full-on racing, all older bearing and seal designs are upgraded to the best and latest specs and designs.

Each pack of Premier CSK Clutch Springs contains a complete set of heavy-duty springs. Up to 15% stronger than the original.

Customer should be advised that after installation of a CSK kit the clutch lever will feel slightly ‘heavier’ than standard

All Balls replacement shock bumper, constructed from a stiffer rubber All Balls shock bumpers provide a brilliant fit & better feel when your shock bottomed out.

All new assembly sold complete with Hot Rods connecting rod.

• The Hot Rods complete crankshaft includes their famed connecting rod; durability at a level OEM rods can only dream of.
• Factory assembled and trued to O.E.M. specifications, Hot Rods cranks will meet or surpass the OEM in performance. Hot Rods makes installing the complete crankshaft simple and easy.
• Crankshaft is completely rebuildable with genuine Hot Rods connecting rods.

Note: Crank bearings and seals sold separately.

Quality design and construction of every All Balls piece meets the toughest standards and conditions - from daily commuting to full-on racing, all older bearing and seal designs are upgraded to the best and latest specs and designs.

One kit does it all! All of the bearings, seals, shafts*, bushings, and thrust bearings (if required) in one all-inclusive kit to do the job correctly and completely.

• All bearing shafts manufactured with 52100 bearing steel that is hardened and centerless ground for a precision fit and extended wear life.
• Steel spacers are case-hardened and plated for resistance to wear and corrosion.
• No more hunting around for missing pieces costing you time and extra money.
• Needle thrust bearings have been replaced with Teflon bearings. Designed to live longer in water and dirt.

* Not included in all kits.

Note: A limited number of kits only available with bearings and seals.

Modern bikes are built to withstand extreme conditions, but suspension linkage bearings are often the first to wear out. Constant exposure to dust, mud, and moisture, followed by wet storage, accelerates wear and causes suspension slop. Restore your rear suspension's full performance with a high-quality All Balls Racing swingarm linkage bearing set.

Features:

• Replacement bearing kit for swingarm linkages.
• OEM quality parts at a fraction of the price.
• Kit includes bearings, seals and spacers needed for a full rebuild.

HFP replacement fuel pumps, modules, assemblies, and kit components are designed to meet or exceed OEM specifications, and feature upgrades that improve on the OEM design. Upgraded polymers, brushes, and commutators ensure long life and durability in multiple fuel blends.

• OEM or better performance
• Polished corrosion-resistant case to help minimize seizing during non-operation
• Specifically designed for quiet operation
• Drop-in replacement
• Gradient density fuel strainer for superior contaminant filtration
• Patented check valve technology
• Compatible with modern ethanol-infused pump gasoline

Ideal replacement for dirt bikes.

Features:

• Anti-swell alloy impregnated heavy-duty cork-based facings.
• Smooth clutch take up compared to paper clutches, which can ‘snatch’.
• Steel separator plates increase flywheel effect of the engine and improve performance.

NOTE: This Vertex Top End Gasket Set contains all components pictured.

Produced in the U.S.A. with the latest materials and technology in gasket production to Vertex specifications. Vertex gaskets ensure long-lasting performance and leak prevention for your rebuild needs. Vertex's replacement gaskets and seals are available as top-end kits, complete engine kits, or as an oil seal kit.

• These sets include the head, base, and exhaust gaskets, valve seals, O-rings and other gaskets to complete a top-end rebuild.

GOLDfren began manufacturing sintered disc brake pads for a wide range of off-road and road motorcycles in 1991, nearly three decades on from their first motorcycle brake pads GOLDfren has become one of the largest aftermarket manufacturers in the motorcycle brake disc pad industry. Their development of next-generation products has kept them at the technological forefront of Sintered Friction Braking providing you with confidence in the performance, durability and reliability of your brakes.

K5 Series:

The K5 sintered compound is optimal for off-road motorcycles and ATVs. It is recommended for riders who demand great off-road stopping power and brake pad durability when riding on tough off-road terrains. The K5 series is designed for low abrasive interaction with the rotor, long life and self-cleaning capabilities necessary in off-road riding conditions. Friction materials contain metal-ceramic with a sophisticated bronze-graphite and full-metal mixture formulation with fine friction particles to achieve optimal friction properties.

Features:

• High static friction coefficient
• Good abrasive resistance
• Self-cleaning capability
• Low abrasive interaction with the brake rotor material
• Up to 3 times longer operational life compared to organic and Kevlar composite materials

Application:

• Developed specifically for off-road motorcycles & ATVs
• Can be used on both front and rear brakes
• Could be used on the rear brake of road racing motorcycles

Operating Parameters:

• Specific pressure: 2.0 Mpa
• Sliding velocity: 20 m/s
• Constant maximum temp: 500°C
• Short time maximum temp: 750°C
• Counter-surfaces: steel disks

What is a sintered brake pad?

GOLDfren only manufacturers sintered brake pads that contain metal-ceramic and ceramic-carbon friction materials, these materials allow for less brake dust and a quieter braking experience. Sintered brake pads are made by fusing together metallic particles under high temperature and pressure which enhances friction properties and pad life, resulting in longer life and stronger braking. Sintered brake pads experience no brake fade when operating at high temperatures and in wet conditions. They also last up to 5 times longer than organic pads and provide additional braking strength. All materials used are environmentally friendly and do not contain any lead, asbestos, fibreglass or formaldehyde.

Reminder: one set of brake pads services one brake disc, if you are servicing multiple discs you will need multiple sets of brake pads.

NOTE: This Vertex Top End Gasket Set contains all components pictured.

Produced in the U.S.A. with the latest materials and technology in gasket production to Vertex specifications. Vertex gaskets ensure long-lasting performance and leak prevention for your rebuild needs. Vertex's replacement gaskets and seals are available as top-end kits, complete engine kits, or as an oil seal kit.

• These sets include the head, base, and exhaust gaskets, valve seals, O-rings and other gaskets to complete a top-end rebuild.

PV SERIES – Semi-Sintered Pads

New high durability semi-sintered pads that have the brake response of an organic but the durability of a sintered pad. For sport bike use only.

These brake disks are made of 420 stainless steel, providing excellent corrosion resistance.

Features:

• Hardened to 36HRC for excellent braking performance and durability.
• Precision ground surfaces.
• Laser engraved with part number and minimum thickness specification.

GOLDfren began manufacturing sintered disc brake pads for a wide range of off-road and road motorcycles in 1991, nearly three decades on from their first motorcycle brake pads GOLDfren has become one of the largest aftermarket manufacturers in the motorcycle brake disc pad industry. Their development of next-generation products has kept them at the technological forefront of Sintered Friction Braking providing you with confidence in the performance, durability and reliability of your brakes.

S3 Series:

The S3 sintered compound is optimal in dry and wet conditions for road & off-road motorcycles. For the road application, S3 pads are suitable for both the front and rear brake while on off-road applications the S3 is only recommended for the front brake. The S3 series is designed for low abrasive interaction with the rotor and quieter braking due to the ceramic composite material. It has an HH friction rating and performs better at higher temperatures than the AD compound. Friction materials contain metal-ceramic with a bronze-graphite and non-metallic friction additives are spread evenly on the base fine bronze body to achieve optimal friction properties.

Features:

• Very high static friction coefficient
• Minimal difference between wet and dry braking performance
• Good abrasive resistance
• Low abrasive interaction with the brake rotor material
• Longer life compared to organic and Kevlar composite materials

Application:

• For riders who demand a bit more than average from their bikes
• Recommended on both front and rear brakes (road application)
• Can also be used on the front brakes of off-road bikes and ATVs
• Works well on both dry and wet conditions

Operating Parameters:

• Specific pressure: 3.0 Mpa
• Sliding speed: 45 m/s
• Constant maximum temp: 450°C
• Short time maximum temp: 800°C
• Counter-surfaces: steel disks

What is a sintered brake pad?

GOLDfren only manufacturers sintered brake pads that contain metal-ceramic and ceramic-carbon friction materials, these materials allow for less brake dust and a quieter braking experience. Sintered brake pads are made by fusing together metallic particles under high temperature and pressure which enhances friction properties and pad life, resulting in longer life and stronger braking. Sintered brake pads experience no brake fade when operating at high temperatures and in wet conditions. They also last up to 5 times longer than organic pads and provide additional braking strength. All materials used are environmentally friendly and do not contain any lead, asbestos, fibreglass or formaldehyde.

Reminder: one set of brake pads services one brake disc, if you are servicing multiple discs you will need multiple sets of brake pads.